scholarly journals Precision Hard Turning of Ti6Al4V Using Polycrystalline Diamond Inserts: Surface Quality, Cutting Temperature and Productivity in Conventional and High-Speed Machining

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5677
Author(s):  
Elshaimaa Abdelnasser ◽  
Azza Barakat ◽  
Samar Elsanabary ◽  
Ahmed Nassef ◽  
Ahmed Elkaseer
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Polycrystalline Diamond ◽  
Depth Of Cut ◽  
High Speed Machining ◽  
Conventional Machining

This article presents the results of an experimental investigation into the machinability of Ti6Al4V alloy during hard turning, including both conventional and high-speed machining, using polycrystalline diamond (PCD) inserts. A central composite design of experiment procedure was followed to examine the effects of variable process parameters; feed rate, cutting speed and depth of cut (each at five levels) and their interaction effects on surface roughness and cutting temperature as process responses. The results revealed that cutting temperature increased with increasing cutting speed and decreasing feed rate in both conventional and high-speed machining. It was found that high-speed machining showed an average increase in cutting temperature of 65% compared with conventional machining. Nevertheless, high-speed machining showed better performance in terms of lower surface roughness despite using higher feed rates compared to conventional machining. High-speed machining of Ti6Al4V showed an improvement in surface roughness of 11% compared with conventional machining, with a 207% increase in metal removal rate (MRR) which offered the opportunity to increase productivity. Finally, an inverse relationship was verified between generated cutting temperature and surface roughness. This was attributed mainly to the high cutting temperature generated, softening, and decreasing strength of the material in the vicinity of the cutting zone which in turn enabled smoother machining and reduced surface roughness.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Development of Tooling Cost Model for High Speed Hard Turning

2011 ◽  
Vol 418-420 ◽  
pp. 1482-1485 ◽  
Author(s):  
Erry Yulian Triblas Adesta ◽  
Muataz Al Hazza ◽  
Delvis Agusman ◽  
Agus Geter Edy Sutjipto
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cost Model ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Predictive Regression ◽  
Aisi 4340

The current work presents the development of cost model for tooling during high speed hard turning of AISI 4340 hardened steel using regression analysis. A set of experimental data using ceramic cutting tools, composed approximately of Al2O3 (70%) and TiC (30%) on AISI 4340 heat treated to a hardness of 60 HRC was obtained in the following design boundary: cutting speeds (175-325 m/min), feed rate (0.075-0.125 m/rev), negative rake angle (0 to -12) and depth of cut of (0.1-0.15) mm. The output data is used to develop a new model in predicting the tooling cost using in terms of cutting speed, feed rate, depth of cut and rake angle. Box Behnken Design was used in developing the model. Predictive regression model was found to be capable of good predictions the tooling cost within the boundary design.

scholarly journals Flank Wear Modelling in High Speed Hard Milling of AISI D2 Steel

2020 ◽  
Vol 5 (2) ◽  
pp. 50-54
Author(s):  
Muataz Al Hazza ◽  
Khadijah Muhammad
Keyword(s):  
Statistical Analysis ◽  
Wear Rate ◽  
Taguchi Method ◽  
Feed Rate ◽  
High Speed ◽  
Flank Wear ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Machining ◽  
Aisi D2

High speed machining has many advantages in reducing time to the market by increasing the material removal rate. However, final surface quality is one of the main challenges for manufacturers in high speed machining due to the increasing of flank wear rate. In high speed machining, the cutting zone is under high pressure associated with high temperature that lead to increasing of the flank wear rate in which affect the final quality of the machined surface. Therefore, one of the main concerns to the manufacturer is to predict the flank wear to estimate and predict the surface roughness as one of the main outputs of the machining processes. The aim of this study is to determine experimentally the optimum cutting parameters: depth of cut, cutting speed (Vc) and feed rate (f) that maintaining low flank wear (Vb). Taguchi method has been applied in this experiment. The Taguchi method has been universally used in engineering analysis.  JMP statistical analysis software is used to analyse statically the development of flank wear rate during high speed milling of hardened steel AISI D2 to 60 HRD. The experiment was conducted in the following boundaries: cutting speed 200-400 m/min, feed rate of 0.01-0.05 mm/tooth and depth of cut of 0.1-0.2 mm. Analysis of variance ANOVA was conducted as one of important tool for statistical analysis. The result showed that cutting speed is the most influential input factors with 70.04% contribution on flank wear.

scholarly journals Analysis of tool wear and surface roughness in high-speed milling process of aluminum alloy Al6061

2021 ◽  
pp. 71-84
Author(s):  
Nhu-Tung Nguyen ◽  
Dung Hoang Tien ◽  
Nguyen Tien Tung ◽  
Nguyen Duc Luan
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Tool Wear ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Speed ◽  
Milling Process ◽  
Face Milling ◽  
Depth Of Cut ◽  
High Speed Milling

In this study, the influence of cutting parameters and machining time on the tool wear and surface roughness was investigated in high-speed milling process of Al6061 using face carbide inserts. Taguchi experimental matrix (L9) was chosen to design and conduct the experimental research with three input parameters (feed rate, cutting speed, and axial depth of cut). Tool wear (VB) and surface roughness (Ra) after different machining strokes (after 10, 30, and 50 machining strokes) were selected as the output parameters. In almost cases of high-speed face milling process, the most significant factor that influenced on the tool wear was cutting speed (84.94 % after 10 machining strokes, 52.13 % after 30 machining strokes, and 68.58 % after 50 machining strokes), and the most significant factors that influenced on the surface roughness were depth of cut and feed rate (70.54 % after 10 machining strokes, 43.28 % after 30 machining strokes, and 30.97 % after 50 machining strokes for depth of cut. And 22.01 % after 10 machining strokes, 44.39 % after 30 machining strokes, and 66.58 % after 50 machining strokes for feed rate). Linear regression was the most suitable regression of VB and Ra with the determination coefficients (R2) from 88.00 % to 91.99 % for VB, and from 90.24 % to 96.84 % for Ra. These regression models were successfully verified by comparison between predicted and measured results of VB and Ra. Besides, the relationship of VB, Ra, and different machining strokes was also investigated and evaluated. Tool wear, surface roughness models, and their relationship that were found in this study can be used to improve the surface quality and reduce the tool wear in the high-speed face milling of aluminum alloy Al6061

scholarly journals Analysis and Optimization of Ceramic Cutting Tool In Hard Turning of EN-31 Using Factorial Design

2012 ◽  
pp. 53-58
Author(s):  
Chetan Darshan ◽  
Lakhvir Singh ◽  
APS Sethi
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Analysis Of Variance ◽  
Feed Rate ◽  
Hard Turning ◽  
Flank Wear ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Good Surface ◽  
En 31

Manufacturers around the globe persistently looking for the cheapest and quality manufactured machined components to compete in the market. Good surface quality is desired for the proper functioning of the produced parts. The surface quality is influenced by cutting speed, feed rate and depth of cut and many other parameters. In the present study attempt has been made to evaluate the performance of ceramic inserts during hard turning of EN-31 steel. The analysis of variance is applied to study the effect of cutting speed, feed rate and depth of cut on Flank wear and surface roughness. Model is found to be statically significant using regression model, while feed and depth of cut are the factor affecting Flank wear and feed is dominating factors for surface roughness. The analysis of variance was used to analyze the input parameters and there interactions during machining. The developed model predicted response factor at 95% confidence level.

Hard Turning of Hot Work Steel X38CRMOV5-3: Evaluation of Surface Roughness and Current Values Using Cutting Parameters

2020 ◽  
Author(s):  
Ali Kemal Cakir
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Feed Rate ◽  
Hard Turning ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Dry Machining ◽  
Motor Current ◽  
Design Factors

This study evaluates the surface roughness and current values using cutting parameters in the turning of AISI H11 being hot work tool steel under dry machining conditions. The selected design factors are the depth of cut, feed rate, cutting speed. A design of experiments was used to carry out this research. The obtained results were analyzed to determine the effects of input parameters on the resultant surface roughness, current using the analysis of variance (ANOVA) and the Response Surface Methodology (RSM). The experimental results showed that increasing feed rate increased the surface roughness, and current values. The most effective cutting parameter on all the output parameters was found to be the feed rate on the surface roughness. Also, the motor current values were influenced by the 38,48% depth of cut, 23,98% cutting speed, 25,52% feed rate, respectively.

Investigations on the Effect of CNC Dry Hard Turning Process Parameters on Surface Integrity: A Multi-performance Characteristics Optimization

2014 ◽  
Vol 14 (1) ◽  
pp. 23-30 ◽  
Author(s):  
Suha K. Shihab ◽  
Zahid A. Khan ◽  
Aas Mohammad ◽  
Arshad Noor Siddiquee
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Feed Rate ◽  
Hard Turning ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Influential Factor ◽  
Depth Of Cut ◽  
Micro Hardness ◽  
Dry Cutting

AbstractThe cutting parameters such as the cutting speed, the feed rate, the depth of cut, etc. are expected to affect the two constituents of surface integrity (SI), i.e., surface roughness and micro-hardness. An attempt has been made in this paper to investigate the effect of the CNC hard turning parameters on the surface roughness average (Ra) and the micro-hardness (μh) of AISI 52100 hard steel under dry cutting conditions. Nine experimental runs based on an orthogonal array of the Taguchi method were performed and grey relational analysis method was subsequently applied to determine an optimal cutting parameter setting. The feed rate was found to be the most influential factor for both the Ra and the μh. Further, the results of the analysis of variance (ANOVA) revealed that the cutting speed is the most significant controlled factor for affecting the SI in the turning operation according to the weighted sum grade of the surface roughness average and micro-hardness.

The Effect of Vortex Tube Cooling on Surface Roughness and Carbon Footprint in Dry Turning

2014 ◽  
Vol 903 ◽  
pp. 135-138
Author(s):  
Zahari Taha ◽  
Hadi Abdul Salaam ◽  
Phoon Sin Ye ◽  
Tuan Muhammad Yusoff Shah Tuan Ya
Keyword(s):  
Surface Roughness ◽  
Carbon Footprint ◽  
Feed Rate ◽  
Vortex Tube ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Air Cooling ◽  
Coated Carbide

This paper presents a study on the effect of Ranque-Hilsch vortex tube air cooling on surface roughness quality and carbon footprint when turning mild steel workpiece with coated carbide cutting tool. The cutting parameters involved in this study were cutting speed, feed rate and depth of cut. The cutting speed and feed rate were fixed at 160 m/min and 0.10, 0.18 and 0.28 mm/rev, while the depth of cut was varied from 1.0 to 4.0 mm. During the turning process, the cutting temperatures were measured using infrared thermometer and the power consumption was measured using a power and harmonics analyzer and then converted into carbon footprint. The machined parts surface roughness were measured using a surface roughness tester. The results show that machining with Ranque - Hilsch vortex tube reduces the cutting temperature, but the surface roughness and carbon footprint is better under ambient condition except at a higher feedrate.

The Effect of Vortex Tube Air Cooling on Surface Roughness and Power Consumption in Dry Turning

2013 ◽  
Vol 310 ◽  
pp. 348-351 ◽  
Author(s):  
Hadi Abdul Salaam ◽  
Phoon Sin Ye ◽  
Zahari Taha ◽  
Tuan Muhammad Yusoff Shah Tuan Ya
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Feed Rate ◽  
Vortex Tube ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Air Cooling ◽  
Coated Carbide

This paper presents a study of the effect of Ranque-Hilsch vortex tube air cooling on surface roughness quality and power consumption when turning mild steel material with coated carbide cutting tool. The cutting parameters involved in this study were cutting speed, feed rate and depth of cut. The cutting speed and feed rate were fixed at 160 m/min and 0.28 mm/rev, while the depth of cut was varied from 1.0 to 4.0 mm. During the turning process, the cutting temperatures were measured using an infrared thermometer and the power consumption was measured using a power and harmonics analyzer. The machined parts surface roughnesses were measured using a surface roughness tester. The results show that cooling using the Ranque-Hilsch vortex tube air cooling reduces the cutting temperature and the power consumption, but the surface roughness results is better when cooling with environment air.

Sign in / Sign up

Export Citation Format

Share Document