Study on Synthesis Nanomicrostructures of Zinc Borate (Zn3B6O12•3.5H2O) with Different Morphologies

2011 ◽  
Vol 236-238 ◽  
pp. 1687-1691 ◽  
Author(s):  
Hui Ren ◽  
You Ming Cao ◽  
Zhou Qiao Lei
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Scanning Electron Microscopy ◽  
Raw Materials ◽  
Average Length ◽  
Zinc Borate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

The crystal zinc borate (Zn3B6O12·3.5H2O) nano-strips and nano-flakes were successfully prepared by a wet method using boric acid (H3BO3) and Zn(NO3)2·H2O as raw materials in situ aqueous solution, and triethanolamine as the modifying agent. The nano/microstructures and morphologies of the as-obtained samples were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) equipped with an energy dispersive X-ray spectrometer (EDS) and thermogravimetric analysis (TGA). It had been found that the as-prepared materials displayed nanostrips with average length from 100 to 200nm and the thicknesses about 30nm as well as nanoflakes with diameter about 4μm and thickness about several nanometers morphology.

Influence of Fly Ash on Corrosion Resistance of Refractory Forsterite-Spinel Ceramics

2021 ◽  
Vol 325 ◽  
pp. 181-187
Author(s):  
Martin Nguyen ◽  
Radomír Sokolář
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Fly Ash ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transition Zones ◽  
Refractory Ceramics ◽  
Scanning Electron

This article examines the influence of fly ash on corrosion resistance of refractory forsterite-spinel ceramics by molten iron as a corrosive medium. Fly ash in comparison with alumina were used as raw materials and sources of aluminium oxide for synthesis of forsterite-spinel refractory ceramics. Raw materials were milled, mixed in different ratios into two sets of mixtures and sintered at 1550°C for 2 hours. Samples were characterized by X-ray diffraction analysis and thermal dilatometric analysis. Crucibles were then made from the fired ceramic mixtures and fired together with iron at its melting point of 1535°C for 5 hours. The corrosion resistance was evaluated by scanning electron microscopy on the transition zones between iron and ceramics. Mixtures with increased amount of spinel had higher corrosion resistance and mixtures with fly ash were comparable to mixtures with alumina in terms of corrosion resistance and refractory properties.

Morphology of Polyethylene/Montmorillonite Nanocomposites Prepared by In Situ Polymerization

2013 ◽  
Vol 457-458 ◽  
pp. 244-247
Author(s):  
Min Li ◽  
Li Guang Xiao ◽  
Hong Kai Zhao
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reflection Peak ◽  
Basal Reflection ◽  
Scanning Electron

Polyethylene/montmorillonite (PE/MMT) nanocomposites were prepared by in situ polymerization. The morphology of MMT/MgCl2/TiCl4 catalyst and PE/MMT nanocomposites was investigated by scanning electron microscopy (SEM). It can be seen that MMT/MgCl2/TiCl4 catalyst remained the original MMT sheet structures and many holes were found in MMT and the morphology of PE/MMT nanocomposites is part of the sheet in the form of existence, as most of the petal structure. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were carried out to characterize all the samples. XRD results reveal that the original basal reflection peak of PEI1 and PEI2 disappears completely and that of PEI3 become very weak. MMT/MgCl2/TiCl4 catalyst was finely dispersed in the PE matrix. Instead of being individually dispersed, most layers were found in thin stacks comprising several swollen layers.

scholarly journals Preparation, Characterization, and Photocatalytic Properties of Modified Red Mud

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Mingjie Ma ◽  
Guanyu Wang ◽  
Zhengpeng Yang ◽  
Shanxiu Huang ◽  
Weijie Guo ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Scanning Electron Microscopy ◽  
Uv Irradiation ◽  
Red Mud ◽  
Structure Property ◽  
X Ray Diffraction ◽  
X Ray ◽  
Xrf Scanning ◽  
Scanning Electron

Solid waste red mud was modified by HCl leaching. The structure property and composition of modified red mud were investigated by X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET). Under UV irradiation, methyl orange (MO) aqueous solution was photodegraded by modified red mud. The obtained results showed that the specific surface area of modified red mud was 317.14 m2/g, which was about 40 times higher than that of the normal red mud. After UV irradiation for 50 min, the removal percentage of MO reached 94.2%. The study provided a novel way for the application of red mud to the photocatalytic degradation of organic wastes.

Microstructure of In Situ Reaction TiB2/Zn-30Al-1Cu Composites Prepared by Spray Deposition Process

2015 ◽  
Vol 1120-1121 ◽  
pp. 572-575
Author(s):  
Hong Wei Liu ◽  
Feng Wang ◽  
Qiang Zhang ◽  
Xi Wu Li ◽  
Zhi Hui Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Spray Deposition ◽  
Deposition Process ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
X Ray ◽  
Α Phase ◽  
Scanning Electron

An innovative spray deposition technique has been applied to produce in situ TiB2/Zn-30Al-1Cu composites. The microstructures of the spray-deposited composite were studied using optical microscopy, scanning electron microscopy, and X-ray diffraction. Both theoretical and experimental results have shown that the TiB2particulates are formed in the microstructure. It was found that the TiB2particles were distributed in Zn-30Al-1Cu matrix uniformly, and the TiB2particles are about 2 μm in size. Moreover, the presence of the TiB2particles was led to increasing of α’ phase with less 2 μm size in the composites which have a tendency to decompose to α+η structure.

Preparation and Properties of CaF2 Nano-Powder

2016 ◽  
Vol 680 ◽  
pp. 257-260
Author(s):  
Meng Yun Dong ◽  
Cheng Zhang ◽  
Jin Feng Xia ◽  
Hong Qiang Nian ◽  
Dan Yu Jiang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Particle Size ◽  
Sintering Temperature ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Direct Precipitation ◽  
Scanning Electron

CaF2 nano-power was prepared by direct precipitation methods with Ca(NO3)2 and KF as raw materials. The influences of presintering temperature and sintering temperature on the particle size and distribution of CaF2 nano-power were studied by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). This study provided an experimental method for preparation of CaF2 nano-power. The results show that the best presintering temperature of CaF2 nano-power is 500°C and the best sintering temperature of CaF2 ceramic is 900°C.

Preparation and Properties of Sintering Brick from Iron Tailings

2012 ◽  
Vol 512-515 ◽  
pp. 1023-1027
Author(s):  
Ran Fang Zuo ◽  
Gao Xiang Du ◽  
Le Fu Mei ◽  
Wei Juan Guo ◽  
Jing Hui Liao
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Bulk Density ◽  
Raw Materials ◽  
Loss On Ignition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Freeze Thaw ◽  
Scanning Electron

The main objective of this paper was to investigate the addition of iron tailing sintering brick production, in the presence of clay, coal refuses and bentonite. Mixtures containing raw materials of sintering brick and iron tailings were prepared at different proportions (up to 55 wt %), fired at 980°C. Freeze/thaw durability, drying and firing shrinkages were investigated as well as the loss on ignition, bulk density and compressive strength of the fired samples. Their mechanical and microstructure properties were also investigated by differential thermal analysis (DTA/TG), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that compressive strengths of the brick samples are higher than that required by the standards MU15 of GB5101-2003, up to 21.79Mpa with 40% iron tailings corresponding to its higher bulk density completely. Moreover, the results showed that it has such advantages as no lime blowing, uniform color, good freeze/thaw resistance and slight universal frost.

Electro-Less Ni-P Plating Coating of In Situ TiCp/Al-4.5wt.%Cu Vomposites

2015 ◽  
Vol 817 ◽  
pp. 593-598
Author(s):  
Yan Feng Liang ◽  
Sheng Quan Dong ◽  
Gao Hong Li
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Citric Acid ◽  
Optical Microscopy ◽  
X Ray Diffraction ◽  
Citric Acid Concentration ◽  
X Ray ◽  
In Situ Tic ◽  
Scanning Electron

In situ TiCp/Al-4.5wt.%Cu composites have been coated using an electro-less Ni-P plating technique. The morphology and composition of the plating coating have been examined by scanning electron microscopy, optical microscopy, and X-ray diffraction. The results indicated that the coating had a high-phosphorus amorphous microstructure. The coatings microstructures showed significantly changes when the citric acid concentration in the chemical bath was varied in the range 16-20g/L.

Effects of Reductive Conditions on the Electrochemical Properties of LiFePO4/C Derived by Fe3+ Sources

2014 ◽  
Vol 1081 ◽  
pp. 313-317
Author(s):  
Yan Wen Lu ◽  
Yu Ge ◽  
Yue Feng Tang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Raw Materials ◽  
Thermal Method ◽  
X Ray Diffraction ◽  
Sintering Atmosphere ◽  
X Ray ◽  
Electrochemical Capacity ◽  
One Step ◽  
Scanning Electron

A one-step carbon thermal method was used to prepare LiFePO4/C particles by using normal Fe2O3, LiH2PO4and sucrose as raw materials. The effect of H2content in the sintering atmosphere of N2on the morphology and the electrochemical performance were investigated. LiFePO4/C materials were characterized by X-ray diffraction, scanning electron microscopy and the elemental analyzer. The results show that the precursor sintering under the atmosphere of 8%H2+N2exhibits the highest electrochemical capacity (162.3 mAh/g at 0.1C) .

Archaeometric analysis of a fragment of molded stucco cornice with rope from the House of the Mithraeum (Mérida, Spain)

2021 ◽  
pp. 1-22
Author(s):  
Alicia Fernández Díaz ◽  
Ana María Bejarano Osorio ◽  
Macarena Bustamante-Álvarez ◽  
Dolores Julia Yusá Marco ◽  
Sofía Vicente Palomino ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Diffraction Data ◽  
Raw Materials ◽  
Compositional Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Technical Study ◽  
Scanning Electron

Abstract During the excavations carried out since 2017 in the House of the Mithraeum (Casa del Mitreo) in Mérida a collection of paintings was recovered from Room 11, which had been abandoned in the late 3rd c. CE after a fire. The remains included fragments of molded stucco cornices, with braided esparto grass ropes on the reverse that were used to attach them to the ceiling. This article presents the descriptive and technical study of the finds and their compositional analysis using scanning electron microscopy and X-ray diffraction. Data resulting from these analyses allow us to understand the fragments’ composition and technical execution, and even the possible circulation of workshops and raw materials.

Hydrothermal Synthesis of SrSO4:Eu2+ Microcrystals with Different Morphologies and its Luminescence Properties

2014 ◽  
Vol 633-634 ◽  
pp. 341-344 ◽  
Author(s):  
Jia Yue Sun ◽  
Qiu Mei Di ◽  
Liu Han ◽  
Qi Guang Xu ◽  
Chen Liang Ma
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Scanning Electron Microscopy ◽  
Optical Properties ◽  
Hydrothermal Synthesis ◽  
Emission Spectroscopy ◽  
Electron Trapping ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Electron trapping materials SrSO4:Eu2+were prepared by hydrothermal method from fatty alcohol polyoxyethylene (3) ether (AEO-3) aqueous solution at 200 °C for 20 h. The phase structure, microstructure and optical properties were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM) and excitation-emission spectroscopy (PL-PLE), respectively.

Sign in / Sign up

Export Citation Format

Share Document