Anti-seismic Analysis of Masonry-Reinforced Concrete Composite Structure Based on LS-DYNA

2011 ◽  
Vol 243-249 ◽  
pp. 477-480
Author(s):  
Xiao Bin Liu ◽  
Guo Ping Chen ◽  
Ying Yang
Keyword(s):  
Reinforced Concrete ◽  
Composite Structure ◽  
Seismic Analysis ◽  
Masonry Structure ◽  
Wall Structure ◽  
Large Space ◽  
Earthquake Load ◽  
Combined Structure ◽  
Structure Collapse ◽  
Tube Structure

Previous great earthquakes have performed serious structural damages to masonry structure, which also have caused great casualties and property damage, in order to enhance the structural anti-seismic class of civilian buildings, a new kind of combined structure form is introduced in the thesis, which is formed by two parts, masonry structure and special reinforced concrete shear wall structure. The reinforced concrete part can be effective in enhancing the anti-seismic performance of masonry residence, besides reinforced concrete tube structure can also become the nearest refuge when disaster occurred, even when the whole structure collapse, it can still remain relatively complete partial structures and a large space of survival. LS-DYNA, software of finite element, is used to study the structure, simulations of the response procedures of composite structure under earthquake load are made, as well as the destruction of composite structure. According to calculation and analysis, it can be known that this kind of composite structure can obviously improve seismic resistant capability, and the level of destruction is relative smaller, which can meet the requirements for fortification against earthquake that is "keeping intact in minor earthquakes, repairable in medium earthquakes, standing upright in major earthquakes"

Anti-Seismic Analysis of Masonry-Reinforced Concrete Structure Based on LS-DYNA

2011 ◽  
Vol 99-100 ◽  
pp. 870-874
Author(s):  
Xiao Bin Liu ◽  
Guo Ping Chen
Keyword(s):  
Reinforced Concrete ◽  
Composite Structure ◽  
Seismic Analysis ◽  
Shear Wall ◽  
Masonry Wall ◽  
Reinforced Concrete Structure ◽  
Concrete Wall ◽  
Earthquake Load ◽  
Reinforced Concrete Wall ◽  
Combined Structure

composite structure of masonry wall and reinforced concrete wall as A new type of structure, With masonry structure is adopted for the subject, Proper Settings of reinforced concrete shear wall part of combined structure system, It mainly by shear deformation of masonry and bending deformation of reinforced concrete shear wall is mainly composed LS-DYNA, software of finite element, is used to study the structure, simulations of the response procedures of composite structure under earthquake load are made, as well as the destruction of composite structure. According to calculation and analysis, it can be known that this kind of composite structure can obviously improve seismic resistant capability, and the level of destruction is relative smaller, which can meet the requirements for fortification against earthquake that is "keeping intact in minor earthquakes, repairable in medium earthquakes, standing upright in major earthquakes"

Seismic Analysis of Confined Masonry Shear Walls Using the Wide Column Model

2016 ◽  
Vol 857 ◽  
pp. 212-218
Author(s):  
Kiran Rangwani ◽  
Svetlana Brzev
Keyword(s):  
Reinforced Concrete ◽  
Latin American ◽  
Seismic Analysis ◽  
Shear Walls ◽  
Computational Effort ◽  
Wall Structure ◽  
Confined Masonry ◽  
Column Model ◽  
Wall Stiffness ◽  
Lateral Displacements

Confined Masonry (CM) structural system consists of masonry walls enclosed by reinforced concrete (RC) confining elements (tie-columns and tie-beams) and is usually supported by reinforced concrete floors and roof. This technology has been widely used for construction of low-and medium-rise buildings in Latin America, Europe, South Asia, and Middle East, and it has a proven record of good performance in damaging earthquakes. CM construction is not currently practiced in India and is not addressed by Indian design codes. Seismic analysis of CM wall panels can be performed using Wide Column Model (WCM), also known as Equivalent Frame Model. WCM is a macro model where a wall structure and the supporting floors and roof are idealized as a bare frame. CM walls can be modelled as wide columns with transformed section properties accounting for composite action of masonry and RC tie-columns. Beams in these bare frames have rigid segments simulating the effect of wall stiffness, and flexible segments that simulate the effect of floor and roof slabs. WCM has been recognized as a viable model for seismic analysis of CM buildings in Latin American countries, however this model is not well known in India. The results presented in this paper are based on linear elastic analyses of typical multi-storey CM solid walls and walls with openings. The output parameters include shear forces, bending moments, stiffness, and lateral displacements. A comparison of the results obtained using the WCM and the Finite Element Method (FEM) has been presented. WCM can be useful for seismic analysis of CM buildings since it does not require significant computational effort and can be applied using a variety of software packages.

SEISMIC ANALYSIS OF MULTISTOREY REINFORCED CONCRETE STRUCTURES

2019 ◽  
Vol 9 (1) ◽  
pp. 61
Author(s):  
SINGH RAVIKANT ◽  
KUMAR SINGH VINAY ◽  
YADAV MAHESH ◽  
◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Seismic Analysis ◽  
Concrete Structures ◽  
Reinforced Concrete Structures

Comparison of Interstorey Drift in General RC Buildings in Pounding and No Pounding Case

2020 ◽  
Vol 2 (1) ◽  
pp. 40-47
Author(s):  
Anand Dev Bhatt
Keyword(s):  
Seismic Analysis ◽  
Linear Time ◽  
Time History ◽  
Case Analysis ◽  
Rc Buildings ◽  
Adjacent Buildings ◽  
Sufficient Distance ◽  
Earthquake Load ◽  
Interstorey Drift ◽  
Lower Height

 Inter-storey drift is an important parameter of structural behavior in seismic analysis of buildings. Pounding effect in building simply means collision between adjacent buildings due to earthquake load caused by out of phase vibration of adjacent buildings. There is variation in inter-storey drift of adjacent buildings during pounding case and no pounding case. The main objective of this research was to compare the inter-storey drift of general adjacent RC buildings in pounding and no pounding case. For this study two adjacent RC buildings having same number of stories have been considered. For pounding case analysis there is no gap in between adjacent buildings and for no pounding case analysis there is sufficient distance between adjacent buildings. The model consists of adjacent buildings having 4 and 4 stories but unequal storey height. Both the buildings have same material & sectional properties. Fast non-linear time history analysis was performed by using El-centro earthquake data as ground motion. Adjacent buildings having different overall height were modelled in SAP 2000 v 15 using gap element for pounding case. Finally, analysis was done and inter-storey drift was compared. It was found that in higher building inter-storey drift is greater in no pounding case than in pounding case but in adjacent lower height building the result was reversed. Additionally, it was found that in general residential RC buildings maximum inter-storey drift occurs in 2nd floor.

Implementing the performance-based seismic design for new reinforced concrete structures: Comparison among ASCE/SEI 41, TBI, and LATBSDC

2021 ◽  
pp. 875529302098196
Author(s):  
Siamak Sattar ◽  
Anne Hulsey ◽  
Garrett Hagen ◽  
Farzad Naeim ◽  
Steven McCabe
Keyword(s):  
Reinforced Concrete ◽  
Los Angeles ◽  
Seismic Design ◽  
Common Ground ◽  
Seismic Analysis ◽  
Tall Buildings ◽  
The United States ◽  
Analysis And Design ◽  
Performance Based Seismic Design ◽  
New Buildings

Performance-based seismic design (PBSD) has been recognized as a framework for designing new buildings in the United States in recent years. Various guidelines and standards have been developed to codify and document the implementation of PBSD, including “ Seismic Evaluation and Retrofit of Existing Buildings” (ASCE 41-17), the Tall Buildings Initiative’s Guidelines for Performance-Based Seismic Design of Tall Buildings (TBI Guidelines), and the Los Angeles Tall Buildings Structural Design Council’s An Alternative Procedure for Seismic Analysis and Design of Tall Buildings Located in the Los Angeles Region (LATBSDC Procedure). The main goal of these documents is to regularize the implementation of PBSD for practicing engineers. These documents were developed independently with experts from varying backgrounds and organizations and consequently have differences in several degrees from basic intent to the details of the implementation. As the main objective of PBSD is to ensure a specified building performance, these documents would be expected to provide similar recommendations for achieving a given performance objective for new buildings. This article provides a detailed comparison among each document’s implementation of PBSD for reinforced concrete buildings, with the goal of highlighting the differences among these documents and identifying provisions in which the designed building may achieve varied performance depending on the chosen standard/guideline. This comparison can help committees developing these documents to be aware of their differences, investigate the sources of their divergence, and bring these documents closer to common ground in future cycles.

Comparative study of finite element analysis of steel silos with rectangular and I stiffeners

2021 ◽  
Vol 10 (1) ◽  
pp. 9
Author(s):  
Prasad Lakshmi ◽  
Neethu Elsa Anil
Keyword(s):  
Reinforced Concrete ◽  
Element Analysis ◽  
Plate Structures ◽  
Steel Reinforced Concrete ◽  
Wide Range ◽  
Earthquake Load ◽  
The Stability ◽  
Dynamic Loading Conditions ◽  
Steel Silos ◽  
Static And Dynamic Loading

Silos are used by a wide range of industries to store bulk solids in quantities ranging from a few tones to hundreds or thousands of tones. They can be constructed of steel or reinforced concrete. Steel bins range from heavily stiffened flat plate structures to efficient unstiffened shell structures. They can be closed or open. They are subjected to many different static and dynamic loading conditions, mainly due to the unique characteristics of stored materials. Wind and earthquake load often undermine the stability of the silos. A steel silo with and without stiffeners is adopted and static structural analysis and dynamic analysis is done. The analysis is done by idealizing geometry, material and boundary conditions. Keywords: steel, reinforced concrete, silos.

Tame Valley Viaduct Assessment and Strengthening

2016 ◽  
Author(s):  
Sarah Jane Blick ◽  
Chris West
Keyword(s):  
Reinforced Concrete ◽  
Design Process ◽  
Composite Structure ◽  
Concrete Slab ◽  
City Centre ◽  
Box Girders ◽  
Reinforced Concrete Slab ◽  
Current Loading ◽  
The Web

Tame Valley Viaduct is a 620m long multi-span highway structure linking Birmingham city centre to the M6 motorway. An assessment in 2004 found the capacity of the structure to be inadequate for current loading, resulting in a requirement for strengthening. Before strengthening works were designed, a comprehensive, refined re-assessment of the structure was undertaken to fully define which areas needed strengthening and which did not. The composite structure comprises a reinforced-concrete slab and typically four longitudinal steel box girders. Each of these longitudinal girders comprises approximately 600 sets of web and flange panels. The scale of the task required automation of the assessment and design process. This paper discusses how the automation was undertaken including the preparation of models to calculate individual panel loading, assessment of the web and flange panels, and the checking of strengthening solutions.

Sign in / Sign up

Export Citation Format

Share Document