Processing of Layered Hydroxyapatite Ceramic Composites

2011 ◽  
Vol 275 ◽  
pp. 143-146 ◽  
Author(s):  
Rumana Sultana ◽  
Jing Zhou Yang ◽  
Xiao Zhi Hu

Layered hydroxyapatite (HA) based ceramic composites consisting of a strong ceramic composite core, 3 mol% yttrium stabilized zirconia (3Y-TZP) with 30 or 40 vol% HA, and a HA-rich porous coating were fabricated using a coating deposition and co-sintering process in the present study. The aim is to develop HA-based bio-ceramic composites that retain the bio-compatibility of HA and the preferred scaffold structure, but have much improved structural properties required for implants. Two different coating techniques, sol-gel derive HA coating and HA solution coating, have been used to deposit the HA coating on the strong HA-containing 3Y-TZP core, which has been pre-sintered at 900°C and has a green-machined surface finish. The upper limit for the final sintering of the layered ceramic composites is set at 1,350°C based on the individual sintering properties of HA and 3Y-TZP. SEM observations have been conducted on the coating surface, sectioned surface of coating and substrate/core to characterize the microstructures of coating and substrate and their interface. Preliminary mechanical tests and XRD tests are also performed to characterise the structural properties at different temperatures.

2003 ◽  
Vol 769 ◽  
Author(s):  
C. K. Liu ◽  
P. L. Cheng ◽  
S. Y. Y. Leung ◽  
T. W. Law ◽  
D. C. C. Lam

AbstractCapacitors, resistors and inductors are surface mounted components on circuit boards, which occupy up to 70% of the circuit board area. For selected applications, these passives are packaged inside green ceramic tape substrates and sintered at temperatures over 700°C in a co-fired process. These high temperature processes are incompatible with organic substrates, and low temperature processes are needed if passives are to be embedded into organic substrates. A new high permeability dual-phase Nickel Zinc Ferrite (DP NZF) core fabricated using a low temperature sol-gel route was developed for use in embedded inductors in organic substrates. Crystalline NZF powder was added to the sol-gel precursor of NZF. The solution was deposited onto the substrates as thin films and heat-treated at different temperatures. The changes in the microstructures were characterized using XRD and SEM. Results showed that addition of NZF powder induced low temperature transformation of the sol-gel NZF phase to high permeability phase at 250°C, which is approximately 350°C lower than transformation temperature for pure NZF sol gel films. Electrical measurements of DP NZF cored two-layered spiral inductors indicated that the inductance increased by three times compared to inductors without the DP NZF cores. From microstructural observations, the increase is correlated with the changes in microstructural connectivity of the powder phase.


Author(s):  
Patrick Knöbelreiter ◽  
Thomas Pock

AbstractIn this work, we propose a learning-based method to denoise and refine disparity maps. The proposed variational network arises naturally from unrolling the iterates of a proximal gradient method applied to a variational energy defined in a joint disparity, color, and confidence image space. Our method allows to learn a robust collaborative regularizer leveraging the joint statistics of the color image, the confidence map and the disparity map. Due to the variational structure of our method, the individual steps can be easily visualized, thus enabling interpretability of the method. We can therefore provide interesting insights into how our method refines and denoises disparity maps. To this end, we can visualize and interpret the learned filters and activation functions and prove the increased reliability of the predicted pixel-wise confidence maps. Furthermore, the optimization based structure of our refinement module allows us to compute eigen disparity maps, which reveal structural properties of our refinement module. The efficiency of our method is demonstrated on the publicly available stereo benchmarks Middlebury 2014 and Kitti 2015.


2021 ◽  
Vol 118 (24) ◽  
pp. 243902
Author(s):  
Yongqiao Zhu ◽  
Shiquan Lin ◽  
Wenchao Gao ◽  
Miao Zhang ◽  
Dawei Li ◽  
...  

2021 ◽  
Vol 127 (5) ◽  
Author(s):  
M. M. El-Desoky ◽  
Ibrahim Morad ◽  
Mohamed. A. Ali ◽  
Atif Mossad Ali ◽  
M. A. Sayed ◽  
...  

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Erik Poloni ◽  
Florian Bouville ◽  
Christopher H. Dreimol ◽  
Tobias P. Niebel ◽  
Thomas Weber ◽  
...  

AbstractThe brick-and-mortar architecture of biological nacre has inspired the development of synthetic composites with enhanced fracture toughness and multiple functionalities. While the use of metals as the “mortar” phase is an attractive option to maximize fracture toughness of bulk composites, non-mechanical functionalities potentially enabled by the presence of a metal in the structure remain relatively limited and unexplored. Using iron as the mortar phase, we develop and investigate nacre-like composites with high fracture toughness and stiffness combined with unique magnetic, electrical and thermal functionalities. Such metal-ceramic composites are prepared through the sol–gel deposition of iron-based coatings on alumina platelets and the magnetically-driven assembly of the pre-coated platelets into nacre-like architectures, followed by pressure-assisted densification at 1450 °C. With the help of state-of-the-art characterization techniques, we show that this processing route leads to lightweight inorganic structures that display outstanding fracture resistance, show noticeable magnetization and are amenable to fast induction heating. Materials with this set of properties might find use in transport, aerospace and robotic applications that require weight minimization combined with magnetic, electrical or thermal functionalities.


2021 ◽  
pp. 002199832110115
Author(s):  
Shaikbepari Mohmmed Khajamoinuddin ◽  
Aritra Chatterjee ◽  
MR Bhat ◽  
Dineshkumar Harursampath ◽  
Namrata Gundiah

We characterize the material properties of a woven, multi-layered, hyperelastic composite that is useful as an envelope material for high-altitude stratospheric airships and in the design of other large structures. The composite was fabricated by sandwiching a polyaramid Nomex® core, with good tensile strength, between polyimide Kapton® films with high dielectric constant, and cured with epoxy using a vacuum bagging technique. Uniaxial mechanical tests were used to stretch the individual materials and the composite to failure in the longitudinal and transverse directions respectively. The experimental data for Kapton® were fit to a five-parameter Yeoh form of nonlinear, hyperelastic and isotropic constitutive model. Image analysis of the Nomex® sheets, obtained using scanning electron microscopy, demonstrate two families of symmetrically oriented fibers at 69.3°± 7.4° and 129°± 5.3°. Stress-strain results for Nomex® were fit to a nonlinear and orthotropic Holzapfel-Gasser-Ogden (HGO) hyperelastic model with two fiber families. We used a linear decomposition of the strain energy function for the composite, based on the individual strain energy functions for Kapton® and Nomex®, obtained using experimental results. A rule of mixtures approach, using volume fractions of individual constituents present in the composite during specimen fabrication, was used to formulate the strain energy function for the composite. Model results for the composite were in good agreement with experimental stress-strain data. Constitutive properties for woven composite materials, combining nonlinear elastic properties within a composite materials framework, are required in the design of laminated pretensioned structures for civil engineering and in aerospace applications.


1865 ◽  
Vol 155 ◽  
pp. 71-202 ◽  

I. About the year 1780 it was distinctly proved that the same weights of different bodies require unequal quantities of heat to raise them through the same temperature, or on cooling through the same number of thermometric degrees, give out unequal quantities of heat. It was recognized that for different bodies the unequal quantities of heat, by which the same weights of different bodies are heated through the same range, must be determined as special constants, and considered as characteristic of the individual bodies. This newly discovered property of bodies Wilke designated as their specific heat , while Crawford described it as the comparative heat, or as the capacity of bodies for heat . I will not enter upon the earliest investigations of Black, Irvine, Crawford, and Wilke, with reference to which it may merely be mentioned that they depend essentially on the thermal action produced when bodies of different temperatures are mixed, and that Irvine appears to have been the first to state definitely and correctly in what manner this thermal action (that is, the temperature resulting from the mixture) depends on the original temperature, the weights, and the specific heats of the bodies used for the mixture. Lavoisier and Laplace soon introduced the use of the ice-calorimeter as a method for determining the specific heat of bodies; and J. T. Mayer showed subsequently that this determination can be based on the observation of the times in which different bodies placed under comparable conditions cool to the same extent by radiation. The knowledge of the specific heats of solid and liquid bodies gained during the last century, and in the first sixteen years of the present one, by these various methods, may be left unmentioned. The individual determinations then made were not so accurate that they could be compared with the present ones, nor was any general conclusion drawn in reference to the specific heats of the various bodies. 2. Dulong and Petit’s investigations, the publication of which commenced in 1818, brought into the field more accurate determinations, and a general law. The investigations of the relations between the specific heats of the elements and their atomic weights date from this time, and were afterwards followed by similar investigations into the relations of the specific heats of compound bodies to their composition. In order to give a general view of the results of these investigations, it is desirable to present, for the elements mentioned in the sequel, a synopsis of the atomic weights assumed at different times, and of certain numbers which stand in the closest connexion with these atomic weights.


1984 ◽  
Vol 32 ◽  
Author(s):  
Rustum Roy ◽  
S. Komarneni ◽  
D.M. Roy

ABSTRACTInstead of aiming to prepare homogeneous gels and xerogels, this paper reports on work done to prepare deliberately diphasic materials. This has been achieved by three different paths: (1) mixing 2 sols; (2) mixing 1 sol with 1 solution; and (3) post formation diffusion of either one or two solutions.By the last named process we have made SiO2, mullite and alumina based composites, with silver halides, BaSO4, CdS, etc., as the dispersed phase. The crystal size can be confined to the initial pores by rapid diffusion giving rise to extremely fine second phases in the submicron range. Subsequent reduction of appropriate metallic salts can be used to give finely dispersed metals (e.g. Cu, Ni) in essentially any xerogel matrix. The open porosity makes these metal atoms very accessible.By the first two processes we have made both single phase and di-phasic gels of the same composition (prototype: mullite) and shown that though they cannot be distinguished by XRD, SEM, and TEM, by DTA and thermal processing, they are radically different. Such di-phasic gels store more metastable energy than any other solids.


2010 ◽  
Vol 105-106 ◽  
pp. 179-183 ◽  
Author(s):  
De Gui Zhu ◽  
Hong Liang Sun ◽  
Yu Shu Wang ◽  
Liang Hui Wang

Fully dense samples of TiB2-TiCX and TiB2-TiCX/15SiC ceramic composites were fabricated by in-situ synthesis under hot isostatic pressing from TiH2, B4C and SiC powders. Their oxidized behaviors at different temperatures were tested. Optical micrograph studies and thermo-gravimetric analyses show that the highest effective temperature of oxidation resistance is 700°C for TiB2-TiCX, and 1100°C for TiB2-TiCX/15SiC. The weight gain of TiB2-TiCX/15SiC below 1100°C is quite low, and it rises up suddenly when the temperature reaches 1200°C. Thus, the highest effective temperature of oxidation resistance is 1100°C for TiB2-TiCX/15SiC. The oxidation dynamic curves of TiB2-TiCX/15SiC ceramics accord with the parabola’s law. The activation energy of TiB2-TiCx/15SiC (189.87kJ.mol-1) is higher than that of TiB2-TiCx (96.44kJ.mol-1). In the oxidation process of TiB2-TiCx/15SiC, TiB2 reacts with oxygen and generates TiO2 and B2O3 at first. A layer of whole homogeneous oxide film cannot be formed, in the mean time, the oxidation of TiC begins. When temperature goes up to 1000°C, TiC phase is totally oxidized. SiC is oxidized to SiO2 at about 900°C, Meanwhile, TiO2 forms denser film than B2O3, which grows and covers the surface of the material, and gives better property of oxidation resistance.


2007 ◽  
Vol 27 (5-8) ◽  
pp. 1065-1068 ◽  
Author(s):  
M.P.F. Graça ◽  
M.A. Valente ◽  
M. Peres ◽  
A. Cruz ◽  
M.J. Soares ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document