Surface Nanocrystallines of Fe3Al Produced by Surface Mechanical Attrition

2011 ◽  
Vol 320 ◽  
pp. 325-328 ◽  
Author(s):  
Jiang Wei Ren ◽  
Dong Li ◽  
Pei Quan Xu
Keyword(s):  
Grain Size ◽  
Surface Layer ◽  
Surface Mechanical Attrition Treatment ◽  
Electronic Microscopy ◽  
X Ray ◽  
Structure And Morphology ◽  
Mechanical Attrition ◽  
Deformed Layer ◽  
Fe3al Intermetallic ◽  
Morphology Of Surface

A nanocrystallines surface layer was produced in Fe3Al intermetallic compound by surface mechanical attrition treatment (SMAT). The microstructure of deformed layer, phase structure and morphology of surface nanocrystallines were characterized through optical microscopy, X-ray diffractometry, transmission electronic microscopy and high resolution electronic microscopy. The results show that a deformed layer about 11μm wide is produced after 10min surface mechanical attrition. The grains on the top surface of Fe3Al are refined to nanocrystallines and the grain size of nanocrystallines is about 35nm. High density dislocations collect on the boundaries of grains. The formation of nanocrystallines is controlled by grain subdivision mechanism.

Interface Diffusion in Cu Processed by Means of Surface Mechanical Attrition Treatment

2009 ◽  
Vol 289-292 ◽  
pp. 557-563 ◽  
Author(s):  
Z.B. Wang ◽  
K. Wang ◽  
K. Lu ◽  
Gerhard Wilde ◽  
Sergiy V. Divinski
Keyword(s):  
Grain Size ◽  
Surface Layer ◽  
Subsurface Layer ◽  
Coarse Grained ◽  
Surface Mechanical Attrition Treatment ◽  
Nanostructured Surface ◽  
Radiotracer Technique ◽  
Mechanical Attrition ◽  
The Difference ◽  
Effective Diffusivities

A nanostructured surface layer with a gradient microstructure was produced on a Cu plate by means of the surface mechanical attrition treatment (SMAT). Diffusion of Ni in the nanostructured layer was investigated by the radiotracer technique at temperatures from 383 to 438 K. The measured diffusion profiles consist of two distinct sections with different slopes, the steep one corresponding to the top surface layer with the grain size of 10 to 25 nm and the shallow one corresponding to a subsurface layer with a grain size of 25 to 100 nm. The effective diffusivities derived from both sections are more than 2 orders of magnitudes higher than the grain boundary diffusivities in coarse-grained Cu. The significantly accelerated diffusion rates are expected to be associated with the “non-equilibrium” states of interfaces in the nanostructured surface layer induced by SMAT. The difference between the diffusivities in the top and sub- surface layer might result from the fact that most interfaces developed from twin boundaries in the former while produced by dislocation activities in the latter.

Thermal Stability of Nanocrystallized Surface Layer in Al-Zn-Mg Alloy by Surface Mechanical Attrition Treatment

2007 ◽  
Vol 546-549 ◽  
pp. 1129-1134 ◽  
Author(s):  
Jin Fang Ma ◽  
Lan Qing Hu ◽  
Xu Guang Liu ◽  
Bing She Xu
Keyword(s):  
Thermal Stability ◽  
Grain Size ◽  
Surface Layer ◽  
Boundary Migration ◽  
Mg Alloy ◽  
Surface Mechanical Attrition Treatment ◽  
Mechanical Attrition ◽  
Nanostructured Layer ◽  
Average Grain Size ◽  
Thermal Stability Of

After surface mechanical attrition treatment (SMAT) for Al-Zn-Mg alloy, a gradient structure with average grain size increased from 20nm in surface layer to about 100nm at a depth of 20μm was formed. The thermal stability of surface nanostructured layer in Al-Zn-Mg alloy samples was investigated by vacuum annealing at 100°C, 150°C, 200°C and 250°C for 1h, respectively. The microstructural evolution as well as the microhardness along the depth from top surface layer to matrix of SMATed samples was analyzed. Experimental results showed that the grain size of surface nanocrystallites remains in submicro-scale, ranging from 300nm to 400nm, when annealed at a temperature of 250°C, and the microhardness of surface nanostructured layer was still high compared with that of matrix, indicating satisfying thermal stability of nanocrystallized layer. This might be attributed to the presence of substantive trident grain boundaries and pinning effect of dispersive precipitated phases in nanocrystalline materials, which hindered the grain boundary migration that leading to grain growth.

Structural and thermodynamic properties of nanocrystalline fcc metals prepared by mechanical attrition

1992 ◽  
Vol 7 (7) ◽  
pp. 1751-1761 ◽  
Author(s):  
J. Eckert ◽  
J.C. Holzer ◽  
C.E. Krill ◽  
W.L. Johnson
Keyword(s):  
Thermal Analysis ◽  
Grain Size ◽  
Melting Point ◽  
Grain Boundary ◽  
Bulk Modulus ◽  
Atomic Level ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fcc Metals ◽  
Mechanical Attrition

Nanocrystalline fcc metals have been synthesized by mechanical attrition. The crystal refinement and the development of the microstructure have been investigated in detail by x-ray diffraction, differential scanning calorimetry, and transmission electron microscopy. The deformation process causes a decrease of the grain size of the fcc metals to 6–22 nm for the different elements. The final grain size scales with the melting point and the bulk modulus of the respective metal: the higher the melting point and the bulk modulus, the smaller the final grain size of the powder. Thus, the ultimate grain size achievable by this technique is determined by the competition between the heavy mechanical deformation introduced during milling and the recovery behavior of the metal. X-ray diffraction and thermal analysis of the nanocrystalline powders reveal that the crystal size refinement is accompanied by an increase in atomic-level strain and in the mechanically stored enthalpy in comparison to the undeformed state. The excess stored enthalpies of 10–40% of the heat of fusion exceed by far the values known for conventional deformation processes. The contributions of the atomic-level strain and the excess enthalpy of the grain boundaries to the stored enthalpies are critically assessed. The kinetics of grain growth in the nanocrystalline fcc metals are investigated by thermal analysis. The activation energy for grain boundary migration is derived from a modified Kissinger analysis, and estimates of the grain boundary enthalpy are given.

scholarly journals Production of Surface Layer with Gradient Microstructure and Microhardess on Copper by High Pressure Surface Rolling

Metals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 73
Author(s):  
Juying Li ◽  
Qingsong Mei ◽  
Yana Li ◽  
Beihai Wang
Keyword(s):  
High Pressure ◽  
Surface Layer ◽  
Pure Copper ◽  
X Ray Diffraction ◽  
Electronic Microscopy ◽  
X Ray ◽  
Pressure Surface ◽  
Surface Gradient ◽  
Pressure Time ◽  
Gradient Microstructure

Pure copper was subjected to high-pressure surface rolling (HPSR) to obtain a surface gradient layer. Effects of HPSR parameters on the surface microstructure and microhardness of Cu were investigated by using optical microscopy, transmission electronic microscopy, X-ray diffraction, and the microhardness test. The HPSR surface layer has a gradient microstructure consisting of increasingly refined grains with decreasing depth from the treated surface (DFS). The thicknesses of the refined surface layer can be up to ~1.8 mm, and the grain size of the topmost surface is down to ~88 nm, depending on the HPSR parameters including pressure, time, and temperature. Microhardness of HPSR samples increases with decreasing DFS, with a maximum of ~2.4 times that of the undeformed matrix. The present results indicated that HPSR could be an effective method for the production of a mm-thick surface layer on Cu with gradient microstructure and property.

Surface Nanocrystallization by Surface Mechanical Attrition Treatment

2008 ◽  
Vol 579 ◽  
pp. 91-108 ◽  
Author(s):  
N.R. Tao ◽  
Jian Lu ◽  
K. Lu
Keyword(s):  
Surface Layer ◽  
Grain Refinement ◽  
Mechanical Twinning ◽  
Surface Mechanical Attrition Treatment ◽  
Formation Mechanisms ◽  
Chemical Compositions ◽  
Tensile Fatigue ◽  
Mechanical Attrition ◽  
And Performance ◽  
Mechanical Twins

Based on strain-induced grain refinement, a novel surface mechanical attrition treatment (SMAT) technique has been developed to synthesize a nanostructured surface layer on metallic materials in order to upgrade their overall properties and performance without changing their chemical compositions. In recent several years, the microstructures and properties of surface layer were systematically investigated in various SMAT metals and alloys, including b.c.c., f.c.c. and h.c.p. crystal structures. Different grain refinement approaches and nanocrystalline formation mechanisms were identified in these deformed materials, involving dislocation activities, mechanical twinning and interaction of dislocations with mechanical twins. The properties of the surface layer were measured by means of hardness, tensile, fatigue and wear tests. The enhanced properties of the surface layer are mainly attributed to the strain-induced grain refinement. In this work, we reviewed the microstructures and properties of surface layer in the SMAT materials.

Ultrasonic Surface Mechanical Attrition of Commercially Pure Ti to Induce Nanocrystalline Surface Layer

2010 ◽  
Vol 442 ◽  
pp. 152-157 ◽  
Author(s):  
M. Mansoor ◽  
J. Lu
Keyword(s):  
Pure Titanium ◽  
Nanocrystalline Structure ◽  
Surface Mechanical Attrition Treatment ◽  
X Ray Diffraction ◽  
Annealed Condition ◽  
X Ray ◽  
Commercially Pure ◽  
Transmission Electron ◽  
Mechanical Attrition ◽  
Xrd And Tem

In the domain of incremental nanotechnology, surface mechanical attrition treatment is a technique which can transform superficial structure of a material to nanocrystalline without changing the chemical composition. This study is a part of the development and implementation of the technique by using ultrasonic vibrations. The material used is pure titanium in rolled and annealed condition. The nanocrystalline structure is characterized using X-ray diffraction (XRD), and transmission electron microscopy (TEM). The measured grain size is in the order of 5~60 nm. A correlation in the results of XRD and TEM is also discussed.

Wear Behaviour of Pure Ti with a Nanocrystalline Surface Layer

2011 ◽  
Vol 66-68 ◽  
pp. 1500-1504 ◽  
Author(s):  
Ming Wen ◽  
Cui'e Wen ◽  
Peter D. Hodgson ◽  
Yun Cang Li
Keyword(s):  
Grain Size ◽  
Wear Resistance ◽  
Titanium Surface ◽  
Pure Titanium ◽  
Coarse Grained ◽  
Surface Mechanical Attrition Treatment ◽  
Wear Behaviour ◽  
Wear Properties ◽  
Microstructure Observation ◽  
Mechanical Attrition

A nanocrystalline (NC) layer with the thickness of 30 µm was produced on pure titanium surface by surface mechanical attrition treatment (SMAT). Microstructure observation indicated that the grain size increases with depth from the treated surface. The friction coefficient decreases and the wear resistance increases with the SMAT sample as compared to its coarse-grained counterpart. The improvement of the wear properties could be attributed to the higher hardness of SMAT sample.

Sign in / Sign up

Export Citation Format

Share Document