Effects of HDI/IPDI Ratio on Properties of Waterborne Polyurethane

2012 ◽  
Vol 452-453 ◽  
pp. 674-678
Author(s):  
Ming Ji Zhou ◽  
Qing Ze Jiao ◽  
Yun Zhao ◽  
Wen Jia Cui
Keyword(s):  
Raw Materials ◽  
Average Particle Size ◽  
Waterborne Polyurethane ◽  
Hexamethylene Diisocyanate ◽  
Molar Ratio ◽  
Average Particle ◽  
Isophorone Diisocyanate ◽  
Polyester Polyol ◽  
Elongation At Break ◽  
Light Blue

A waterborne polyurethane (WPU) dispersoid was synthesized through the prepolymer method using aliphatic isocyanates [namely isophorone diisocyanate(IPDI), hexamethylene diisocyanate(HDI)] and self-made polyester polyol as main raw materials. The effects of HDI/IPDI ratio on properties of waterborne polyurethane were discussed. The FTIR results confirmed the successful synthesis of WPU. As the molar ratio of HDI/IPDI increased, the properties (including elongation at break, solvent resistance, viscosity and thermal stability) increased, while the tensile strength and the average particle size decreased. The stable WPU with light blue and translucent were obtained when the HDI/ IPDI ratio was 1.5:1.

Fe3O4 Magnetic Preparation by Bauxite Ore Washing Fine Mud

2014 ◽  
Vol 1010-1012 ◽  
pp. 961-965
Author(s):  
Jian Qiang Xiao ◽  
Guo Wei He ◽  
Yan Jin Hu
Keyword(s):  
Particle Size ◽  
Aging Time ◽  
Average Particle Size ◽  
Xrd Analysis ◽  
Test Methods ◽  
Raw Material ◽  
Molar Ratio ◽  
Average Particle ◽  
Experimental Conditions ◽  
Particle Size Analyzer

Bauxite waste sludge as a raw material, the use of reverse chemical coprecipitation synthesize Fe3O4. Researching temperature, precipitation concentration, aging time and Fe2+/Fe3+ molar ratio effect on the particle size, morphology. Optimal experimental conditions: temperature 70 °C, the precipitant NaOH mass ratio of 10%, aging time 3h, Fe2+/Fe3+ molar ratio of 2:3. Test methods using a laser particle size analyzer, XRD analysis of the products were characterized, the product is Fe3O4, the average particle size of 0.11mm.

Сrystalline structure and dielectric properties of ceramic materials based on AgNbO3

2020 ◽  
Vol 63 (7) ◽  
pp. 75-78
Author(s):  
Polina A. Bezborodova ◽  
◽  
Elena M. Filonenko ◽  
Kseniya R. Erager ◽  
Anatoly V. Butakov ◽  
...  
Keyword(s):  
Rietveld Method ◽  
Average Particle Size ◽  
Ceramic Materials ◽  
Analysis Data ◽  
Molar Ratio ◽  
Average Particle ◽  
Dielectric Parameters ◽  
Low Frequencies ◽  
X Ray ◽  
Substitution Degree

Using the data of qualitative X-ray phase analysis, it was shown that in a wide concentration range at 1223 K compounds based on silver niobate are formed in the condition of the heterovalent substitution of tungsten(VI) ions for niobium(V) ions. These compounds are isomorphic to a perovskite-type structure. Microprobe analysis data allows to determine the homogeneity of the analyzed samples and the correspondence of their experimental compositions to the theoretical ones for the formula Ag1-xNb1-xWxO3. Using the data of X-ray diffraction analysis (Rietveld method) in the Crystallography Data Analysis Software – GSAS, the crystal structure of the obtained compounds was refined. The surface morphology of samples having been obtained at 1373 K was investigated by scanning electron microscopy (SEM). It was shown that with an increase of Nb5+ to W6+ substitution degree for Ag1-xNb1-xWxO3 ceramic samples in the range of the (0.2≤x≤0.8) molar ratio, the average particle size for the studied compositions grows from 1.3 to 5.2 μm, respectively. For the obtained ceramic compounds based on silver niobate with a perovskite-like structure (tetragonal distortion), the temperature-frequency dependences of dielectric parameters in the range 300-900 K were studied. It was found that samples slowly cooled from 1373 K are characterized by low values of (ε ~ 10) and loss (tgδ ~ 0.004 at f = 1 kHz) at room temperature. The ceramics obtained are characterized by relatively high values of dielectric permittivity ε at low frequencies and/or high temperatures. The dielectric parameters of the obtained ceramics are similar to the characteristics of so-called "colossal" dielectric constant materials. The revealed features of the dielectric characteristics of quenched ceramics apparently result from Maxwell-Wagner relaxation at intercrystalline contacts.

scholarly journals Photocatalytic degradation of chlortetracycline hydrochloride in marine aquaculture wastewater under visible light irradiation with CuO/ZnO

2019 ◽  
Vol 80 (7) ◽  
pp. 1249-1256 ◽  
Author(s):  
Jinghua Liu ◽  
Xiaocai Yu ◽  
Liping Wang ◽  
Meicen Guo ◽  
Wanting Zhu ◽  
...  
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Diffuse Reflectance Spectroscopy ◽  
Average Particle Size ◽  
Molar Ratio ◽  
Average Particle ◽  
Marine Aquaculture ◽  
Aquaculture Wastewater ◽  
Co Precipitation ◽  
The Cost

Abstract A CuO/ZnO photocatalyst nanocomposite was successfully prepared by co-precipitation and characterized by investigating its chemical and physical properties by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, UV-vis diffuse reflectance spectroscopy and photoluminescence spectroscopy. The average particle size of CuO/ZnO composite was found to be around 80 nm. The degradation of chlortetracycline hydrochloride pollutants in marine aquaculture wastewater using ZnO and CuO/ZnO was compared and it was found that CuO/ZnO nanocomposite is more efficient than ZnO. The effects of external factors on the photocatalytic effectiveness of nanocomposite were investigated under visible light. Also, the photocatalytic conditions for the degradation of chlortetracycline hydrochloride by the nanocomposite were optimized. Based on both ability and efficiency of degradation, and on the cost and availability, 10:2 molar ratio of Zn2+/Cu2+ and 0.7 g/L nanocomposite, was found to be optimal, in which case the average photocatalytic degradation rate of chlortetracycline hydrochloride reached 91.10%.

Low Temperature Hydrothermal Synthesis of Nanophase BaTiO3 and BaFe12O19 Powders

1996 ◽  
Vol 457 ◽  
Author(s):  
Fatih Dogan ◽  
Shawn O'rourke ◽  
Mao-Xu Qian ◽  
Mehmet Sarikaya
Keyword(s):  
Particle Size ◽  
Hydrothermal Reaction ◽  
Average Particle Size ◽  
Reaction Times ◽  
Nanocrystalline Powders ◽  
Molar Ratio ◽  
Average Particle ◽  
Hydrothermal Conditions ◽  
Processing Variables ◽  
Xrd And Tem

ABSTRACTNanocrystalline powders with an average particle size of 50 nm has been synthesized in two materials systems under hydrothermal conditions below 100°C. Processing variables, such as temperature, concentration and molar ratio of reactants and reaction time were optimized to obtain particles of reduced size and stoichiometric compositions. Hydrothermal reaction takes place between Ba(OH)2 solution and titanium/iron precursors in sealed polyethylene bottles in the BaTiO3 and BaFe12O19 systems, respectively. While crystalline BaTiO3 forms relatively fast within a few hours, formation of fully crystalline and stoichiometric BaFei20i9 require considerably longer reaction times up to several weeks and strongly dependent on the Ba:Fe ratio of the precursors. The structural and compositional evaluation of the nanophase powders were studied by XRD and TEM techniques.

Synthesis of Fe2O3/C Nanocomposite Using Microwave Assisted Calcination Method

2014 ◽  
Vol 896 ◽  
pp. 100-103 ◽  
Author(s):  
Anggi Puspita Swardhani ◽  
Ferry Iskandar ◽  
Abdullah Mikrajuddin ◽  
Khairurrijal
Keyword(s):  
Crystallite Size ◽  
Average Particle Size ◽  
Molar Ratio ◽  
Average Particle ◽  
X Ray ◽  
Molar Ratios ◽  
Microwave Assisted ◽  
Chloride Hexahydrate ◽  
Calcination Method ◽  
Scherrer Method

Fe2O3/C nanocomposites were successfully synthesized using microwave assisted calcination method. Ferric (III) chloride hexahydrate (FeCl36H2O), sodium hydroxide (NaOH), and dextrose monohydrate (C6H12O6H2O) were used as precursors. A microwave oven of 2.445 GHz with a power of 600 W for 20 minutes was employed during the syntheses. Calcination was performed in a simple furnace at 350 °C for 30 min. The molar ratio of C:Fe is the only process parameter. From Scanning Electron Microscope images, the average particle size were 199 nm and 74 nm for the samples with molar ratio of C:Fe of 1:2 and 1:1, respectively. X-ray diffractometer spectra showed that the obtained samples have γ-Fe2O3 (maghemite) crystal structure. Using the Scherrer method, the crystallite size were 61.7, 58.8, 52.5, and 48.8 nm for the samples with the molar ratios of C:Fe of 1:3, 1:2, 1:1, and 2:1, respectively. It means that the crystallite size of the nanocomposite decreases with the increase of the molar ratio of carbon to iron (C:Fe). The Brunauer-Emmett-Teller characterization showed that the surface area as high as 255.6 m2/g is achieved by of the Fe2O3/C nanocomposite with the molar ratio of C:Fe of 1:1.

Minimum Particle Diameter of the Vanadium/Iron Co-Doped Nano TiO2 Transparent Hydrosol at Room Temperature

2014 ◽  
Vol 989-994 ◽  
pp. 611-614
Author(s):  
Ling Li ◽  
Wen Ming Zhang ◽  
Hua Yan Zhang ◽  
Zi Hao Xu ◽  
Sen Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
Room Temperature ◽  
Raw Materials ◽  
Average Particle Size ◽  
Particle Diameter ◽  
Ferric Nitrate ◽  
Average Particle ◽  
Hydrolysis Method ◽  
Vanadium Iron ◽  
Co Doped

Vanadium/iron co-doped nanoTiO2 transparent hydrosol with an average particle size of 3.8 nm was synthesized by a novel complexation-controlled hydrolysis method at room temperature and atmospheric pressure by using TiCl4, ferric nitrate, ammonium metavanadate, etc. as raw materials. The composition, phase structure, particle size, absorbance spectrum, and photocatalytic performance of samples were characterized by XRD, EDS, nanolaser particle size analyzer, and UV-Vis spectrophotometer. The photocatalytic properties of V/Fe doped TiO2 were studied through degrading acid 3R dye, and the results show that when the content of V/Fe was 0.5%, the degradation rate reached more than 96% under irridation for 60 min.

Study on the Synthesis of Polyester Type Waterborne Polyurethane and Modifying by Nano-Sized Particles

2012 ◽  
Vol 217-219 ◽  
pp. 656-660
Author(s):  
Yi Chen ◽  
Wen Yong Liu ◽  
Guang Sheng Zeng ◽  
Xiang Gang Li ◽  
Ling Gu
Keyword(s):  
Small Molecule ◽  
Mass Fraction ◽  
Water Resistance ◽  
Raw Materials ◽  
Waterborne Polyurethane ◽  
Chain Extender ◽  
Polyester Polyol ◽  
Polyurethane Film ◽  
Mechanical Characters

The waterborne polyurethane was prepared by reaction between polyester polyol and isophorone diisocyanat, different nanoparticles were filled into the system for modification. The effect of different ratio of materials, the kinds and mass of nanoparticles on the characters of waterborne polyurethane latex and film were investigated. The results showed that the stable polyurethane latex and polyurethane film with perfect characters could be prepared when the ratio of NNCO/NOH was 2.5~3.0, the DMPA with a mass fraction of 5%~6% was added into reaction as a macromolecule extender after adding small molecule chain extender BPO. Filling nanoparticles into the polyurethane latex could improve the water resistance and mechanical characters of the film. Nano-sized SiO2 was a better modifier than TiO2, and the appropriate mass fraction of SiO2 was 6% of polyurethane raw materials.

Heterophase ceramics in the Hf–Si–Mo–B system obtained by a combination of SHS and hot pressing methods

2019 ◽  
pp. 36-46
Author(s):  
Yu. S. Pogozhev ◽  
M. V. Lemesheva ◽  
A. Yu. Potanin ◽  
S. I. Rupasov ◽  
V. I. Vershinnikov ◽  
...  
Keyword(s):  
Hot Pressing ◽  
Raw Materials ◽  
Average Particle Size ◽  
High Hardness ◽  
Maximum Size ◽  
Composite Ceramic ◽  
Thermal Reduction ◽  
High Mass ◽  
Average Particle ◽  
Chemical Homogeneity

The paper focuses on obtaining heterophase powder ceramics and consolidated ceramics based on borides and silicides of hafnium and molybdenum by combining the methods of self-propagating high-temperature synthesis (SHS) and hot pressing (HP). Composite ceramic SHS powders HfB2–HfSi2–MoSi2 were obtained according to the scheme of magnesium-thermal reduction from oxide raw materials where the combustion wave is characterized by temperatures of 1750–2119 K and high mass combustion rates of 8,4– 9,3 g/s. The structure of synthesized SHS powders consists of relatively large MoSi2 grains up to 10 μm in size and submicron elongated HfB2 grains located mainly inside the MoSi2 grains and rounded Si precipitates. The composition with a lower concentration of boron contains a large number of polyhedral HfSi2 grains with a size of less than 10 μm. The resulting powders are characterized by an average particle size of ~6 μm with a maximum size up to 26 μm. Phase compositions of ceramics consolidated by the HP method and SHS synthesized powders are identical. The microstructure of compact samples consists of faceted HfB2 elongated grains 0,5– 10,0 μm in size, polyhedral HfSi2 and MoSi2 grains up to 8–10 μm in size and silicon interlayers. Consolidated ceramics has a high structural and chemical homogeneity, low residual porosity of 1,1–1,7 %, high hardness of 11,7–12,6 GPa and thermal conductivity of 62–87 W/(m·K).

Preparation of Nano-TiO2 Using a Sol-Gel Process Mediated in Reverse Microemulsion Combined with a Solvent Thermal Technique

2011 ◽  
Vol 287-290 ◽  
pp. 1731-1734 ◽  
Author(s):  
Han Sheng Li ◽  
Hang Xu ◽  
Shi Ying Wang ◽  
Ya Lin Pan ◽  
Qin Wu ◽  
...  
Keyword(s):  
Sol Gel ◽  
Average Particle Size ◽  
High Photocatalytic Activity ◽  
Reverse Microemulsion ◽  
Molar Ratio ◽  
Average Particle ◽  
Anatase Structure ◽  
Sol Gel Process ◽  
Triton X ◽  
Thermal Technique

Anatase nano-titania (nano-TiO2) was prepared by using a sol-gel process mediated in reverse microemulsion combined with a solvent thermal technique. The results show that the anatase structure appears in the calcination temperature range of 400-510°C, while the transformation of anatase into rutile takes place above 510°C. The average particle size (dP) of the nano-TiO2 increases with the rise of water/Triton X-100 molar ratio (ω) but decreases with the rise of acetyl acetone/n-TBT molar ratio (p) and n-hexanol/Triton X-100 molar ratio (m). The obtained TiO2 particles with a small size have high photocatalytic activity.

Sign in / Sign up

Export Citation Format

Share Document