Prediction of Surface Finish and Optimization of Machining Parameters in Turning

2012 ◽  
Vol 463-464 ◽  
pp. 679-683
Author(s):  
Devi Prasad ◽  
Prasad Krishna ◽  
Shrikantha Rao
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Validity And Reliability ◽  
Nose Radius ◽  
Radial Acceleration ◽  
Feed Forward Back Propagation ◽  
Taguchi Design Of Experiments

Surface roughness plays a crucial role in the functional capacity of machined parts. In this work, experiments were carried out on a conventional lathe for different cutting parameters namely feed, spindle speed, depth of cut and tool nose radius according to Taguchi Design of Experiments. Radial acceleration readings were taken with an accelerometer. Optimum cutting parameters and their level of significance were found using Taguchi analysis (ANOVA). Regression analysis was carried out to identify whether the experimental roughness values have fitness characteristic with the process parameters. Recurrence Plots (RP) were obtained using the sensor signals which determine surface roughness qualitatively and Recurrence Quantification Analysis (RQA) technique was used to quantify the RP obtained. Surface finish was predicted using a feed forward back propagation neural network with RQA parameters, cutting parameters and acceleration data as inputs to the network. The validity and reliability of the methods were verified experimentally.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Optimization of Machining Parameters of Valve Steel SUH03 (X45CrSiMo10-2) Using Gray Based Taguchi Method

2015 ◽  
Vol 813-814 ◽  
pp. 376-381 ◽  
Author(s):  
B. Yazhini ◽  
S. Rajeswari ◽  
Sivasakthivel
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Signal To Noise Ratio ◽  
Cutting Parameters ◽  
Gray Relational Analysis ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Nose Radius ◽  
Valve Steel ◽  
Optimal Cutting Parameters

This paper embarks the machining parameters of Turning by optimization using Taguchi’s approach. The optimization is very essential in order to obtain the expected surface quality. The results of cutting parameters of optimization is seen in the Surface Roughness, Tool wear and MRR of the material. The L18 Orthogonal array has been chosen for the optimization of Valve Steel SUH03.The uncoated carbide inserts were used and the four parameters Speed, Feed, Depth of Cut and Nose Radius has been taken as input parameters. The Signal to Noise ratio and Analysis of Variance software has been analyzed using Minitab software through which the optimal cutting parameters of the best surface roughness, tool wear and MRR has been obtained. The final results have been compared by the Gray relational analysis to find the optimum machining conditions of all the parameters.

Optimization of Cutting Parameters for Turning Operation of Titanium Alloy Ti-6Al-4V Material Workpiece Using the Taguchi Method

2013 ◽  
Vol 685 ◽  
pp. 57-62
Author(s):  
Seyyed Pedram Shahebrahimi ◽  
Abdolrahman Dadvand
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Taguchi Method ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Material Tool

One of the most important issues in turning operations is to choose suitable parameters in order to achieve a desired surface finish. The surface finish in machining operation depends on many parameters such as workpiece material, tool material, tool coating, machining parameters, etc. The purpose of this research is to focus on the analysis of optimum cutting parameters to get the lowest surface roughness in turning Titanium alloy Ti-6Al-4V with the insert with the standard code DNMG 110404 under dry cutting condition, by the Taguchi method. The turning parameters are evaluated as cutting speed of 14, 20 and 28 m/min, feed rate of 0.12, 0.14 and 0.16 mm/rev, depth of cut of 0.3, 0.6 and 1 mm, each at three levels. The Experiment was designed using the Taguchi method and 9 experiments were conducted by this process. The results are analyzed using analysis of variance method (ANOVA). The results of analysis show that the depth of cut has a significant role to play in producing lower surface roughness that is about 63.33% followed by feed rate about 30.25%, and cutting speed has less contribution on the surface roughness. Also it was realized that with the use of the confirmation test, the surface roughness improved by 227% from its initial state.

scholarly journals Effect of Nose Radius on Surface Roughness of Diamond Turned Germanium Lenses

2021 ◽  
Author(s):  
Adeniyi Adeleke ◽  
Abou-El-Hossein Khaled ◽  
Odedeyi Peter
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Single Point ◽  
Absolute Error ◽  
Diamond Turning ◽  
Machining Process ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Machining Parameters ◽  
Nose Radius

Abstract The desire for quality infrared lens with better surface finish has brought about the usage of brittle materials like germanium to be machined via a single point diamond turning machining process. However, achieving the required surface finish is complex if special machining techniques and approaches are not employed. In this paper, the effect of two different tool nose radius parameters on surface roughness of single point diamond turned germanium workpiece were studied and analyzed. The machining parameters selected for this experiment were feed, speed and depth of cut. Box-Behnken design was adopted to optimally create a combination of cutting parameters. Measurement of surface roughness after each run in both experiments was achieved using a Taylor Hobson PGI Dimension XL surface Profilometer. The resulting outcomes show that at most experimental runs, the surface roughness value decreased with an increase in nose radius. Mean absolute error was also used to compare the accuracy validation of the two models.

scholarly journals Utilization of Taguchi Approach to Investigate the Effects of Cutting Parameters on Surface Finish of AISI 1020 Steel while turning

2018 ◽  
Vol 8 (01) ◽  
Author(s):  
Mandeep Singh ◽  
Ashwani Kumar
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Steel Surface ◽  
Cutting Parameters ◽  
Influential Factor ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Taguchi Approach ◽  
Dry Turning ◽  
Machined Parts

To judge the success of a machining operation, surface finish of the machined parts is one of the important criteria. The value of optimum machining parameters (for better surface finish) can be either decided on the basis of a large number of experimental trails or design of experiments (DoE) can be used to predict the same with significantly lesser number of experimental trails. The aim of this work was to reveal the application of Taguchi method to study the effect of the machining/cutting parameters for surface finish during turning of AISI 1020 steel under different cutting environments. The results revealed that spindle speed was the most influential factor which affected surface roughness in dry turning as well as wet turning. However, depth of cut was second influential factor in dry turning but feed rate was more influential than depth of cut during wet turning Machining, Turning, Steel, Surface finish, Taguchi, Minitab, Anova

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

scholarly journals The Experimental Investigation of Surface Roughness After Dry Turning of Steel S235

2019 ◽  
Vol 26 (4) ◽  
pp. 179-184
Author(s):  
Justyna Molenda
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Scientific Work ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Workpiece Material ◽  
Important Indicator

AbstractNowadays lot of scientific work inspired by industry companies was done with the aim to avoid the use of cutting fluids in machining operations. The reasons were ecological and human health problems caused by the cutting fluid. The most logical solution, which can be taken to eliminate all of the problems associated with the use of cooling lubricant, is dry machining. In most cases, however, a machining operation without lubricant finds acceptance only when it is possible to guarantee that the part quality and machining times achieved in wet machining are equalled or surpassed. Surface finish has become an important indicator of quality and precision in manufacturing processes and it is considered as one of the most important parameter in industry. Today the quality of surface finish is a significant requirement for many workpieces. Thus, the choice of optimized cutting parameters is very important for controlling the required surface quality. In the present study, the influence of different machining parameters on surface roughness has been analysed. Experiments were conducted for turning, as it is the most frequently used machining process in machine industry. All these parameters have been studied in terms of depth of cut (ap), feed rate (f) and cutting speed (vc). As workpiece, material steel S235 has been selected. This work presents results of research done during turning realised on conventional lathe CDS 6250 BX-1000 with severe parameters. These demonstrate the necessity of further, more detailed research on turning process results.

scholarly journals Process Capability Assessment Using Vision System

2021 ◽  
Vol 13 (2) ◽  
pp. 96-102
Author(s):  
Shivanna Dodda Mallappa ◽  
◽  
Kiran Mysore Bhaskar ◽  
Venkatesh Gude Subbaraya ◽  
Kavitha Shimoga Divakar ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Vision System ◽  
Research Work ◽  
Stable Process ◽  
Process Capability ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Measuring Surface ◽  
Roughness Assessment

Surface roughness assessment would help in predicting a component’s functionality. This clearly shows the significance of measuring the surface roughness of machined components. Thus, each machined component, depending upon its intended function, requires a certain surface finish. To predict the surface roughness of a machined component, a detailed understanding of the machining parameters is essential. This is because, surface roughness generated on a component, depends upon machining parameters speed, feed, and depth of cut. A stable manufacturing process gives a consistent surface finish on all the manufactured components. Thus, only by having a stable process, consistent quality of manufactured products is possible. The capability of the machine is defined as the capability of the machine to carry out the set process efficiently and effectively to produce parts as per the specification limits. Machining parameters, tools, coolant flow rate, etc. An effort has been made in this research work, to show how by measuring surface roughness of machined components process capability can be assessed. Thus, the method is a novel technique of assessing the process capability of a given process. A capable process would help a manufacturing company in meeting customer expectations. The proposed method is of non-contact type, quick, and industry-friendly.

Sign in / Sign up

Export Citation Format

Share Document