Numerical Simulation of Influence of Mudstone Interlayer on Compressive Strength of Salt Rock

2012 ◽  
Vol 512-515 ◽  
pp. 1953-1956
Author(s):  
Feng Shan Han ◽  
Song Li
Keyword(s):  
Numerical Simulation ◽  
Compressive Strength ◽  
Natural Gas ◽  
Radioactive Waste ◽  
Mechanical Behavior ◽  
Uniaxial Compressive Strength ◽  
Failure Process ◽  
Physical Experiment ◽  
Salt Rock ◽  
Oil And Natural Gas

Salt rock is think of ideal storage location for oil and natural gas and radioactive waste deposited, interlayer has negative effect on stability of cavern of storage for oil and natural gas and radioactive waste deposited in salt rock, It is difficult to make complete specimen layered salt rock with interlayer. In this paper Based on Rock Failure Process Analysis Code RAFP2D, influence of mudstone interlayer on uniaxial compressive strength of salt rock is investigated by numerical simulation. Numerical simulation shown that when mechanical parameters such as elastic modulus poison’s ratio and uniaxial compressive strength for salt rock and pure mudstone interlayer and content of mudstone interlayer in salt rock are known, compressive strength and mechanical behavior for salt rock with mudstone interlayer can be effectively and accurately analyzed using RFAP2D. The results for numerical simulation are agreement with true physical experiment of salt rock with mudstone interlayer. It should be noticed that the true physical experimental uniaxial compressive strength of rock is in range of 30% mean uniaxial compressive strength of rock element in RFPA2D，in this case the results for numerical simulation can reflect phenomenon and behavior for true physical experiment of salt rock with mudstone interlayer. That provides new method and avenue to analyze and investigate mechanical behavior for multilayer rock mass based on RAFP2D

Numerical Simulation of Compressive Experiment for Rock with a Natural Interlayer

2012 ◽  
Vol 217-219 ◽  
pp. 1389-1392
Author(s):  
Feng Shan Han ◽  
Li Song
Keyword(s):  
Numerical Simulation ◽  
Compressive Strength ◽  
Process Analysis ◽  
Failure Process ◽  
Peak Load ◽  
Strain Curve ◽  
Confining Pressure ◽  
Physical Experiment ◽  
Stress Strain Curve ◽  
Rock Failure Process

It is difficulty to make physical experiment for compressive experiment of rock with a natural interlayer I Natural interlayer affect greatly on mechanical property of rock. In this paper, Rock Failure Process Analysis Code RFPA is used to simulate influence of natural interlayer to compressive strength of rock by numerical simulation under compression. Through numerical simulation complete stress strain curve and peak load can be obtained for compressive experiment of rock with a natural interlayer. RFPA can be effectively used to investigate anisotropy of compression for rock with natural interlayer under different confining pressure. Numerical simulation show that anisotropy of compressive strength of rock with a natural interlayer varies with inclination of natural interlayer, as the confining pressure increase, the compressive strength, the plasticity and ductility increase for rock with a natural interlayer. That provides new method to analyze and investigate mechanical behavior for multilayer composite material such as rock mass with a natural interlayer，finally Index of Anisotropy for rock with a natural interlayer are put forward

scholarly journals Degradation of Mechanical Behavior of Sandstone under Freeze-Thaw Conditions with Different Low Temperatures

2021 ◽  
Vol 11 (22) ◽  
pp. 10653
Author(s):  
Jingwei Gao ◽  
Chao Xu ◽  
Yan Xi ◽  
Lifeng Fan
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Mechanical Behavior ◽  
Energy Absorption ◽  
Uniaxial Compressive Strength ◽  
Dynamic Strength ◽  
Freezing Temperature ◽  
P Wave ◽  
Freeze Thaw ◽  
P Wave Velocity

This study investigated the effects of freezing temperature under freeze-thaw cycling conditions on the mechanical behavior of sandstone. First, the sandstone specimens were subjected to 10-time freeze-thaw cycling treatments at different freezing temperatures (−20, −40, −50, and −60 °C). Subsequently, a series of density, ultrasonic wave, and static and dynamic mechanical behavior tests were carried out. Finally, the effects of freezing temperature on the density, P-wave velocity, stress–strain curves, static and dynamic uniaxial compressive strength, static elastic modulus, and dynamic energy absorption of sandstone were discussed. The results show that the density slightly decreases as temperature decreases, approximately by 1.0% at −60 °C compared with that at 20 °C. The P-wave velocity, static and dynamic uniaxial compressive strength, static elastic modulus, and dynamic energy absorption obviously decrease. As freezing temperature decreases from 20 to −60 °C, the static uniaxial compressive strength, static elastic modulus, dynamic strength, and dynamic energy absorption of sandstone decrease by 16.8%, 21.2%, 30.8%, and 30.7%, respectively. The dynamic mechanical behavior is more sensitive to the freezing temperature during freeze-thawing cycling compared with the static mechanical behavior. In addition, a higher strain rate can induce a higher dynamic strength and energy absorption.

scholarly journals Numerical Simulation of Rock Failure Process with a 3D Grain-Based Rock Model

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Zengwei Zhang ◽  
Fan Chen ◽  
Chao Zhang ◽  
Chao Wang ◽  
Tuo Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Mechanical Characteristics ◽  
Failure Process ◽  
Wellbore Stability ◽  
Rock Excavation ◽  
Rock Failure Process ◽  
Rock Model ◽  
Walled Cylinder

A grain-based rock model was developed and applied to study mechanical characteristics and failure micromechanics in thick-walled cylinder and wellbore stability tests. The rock is represented as an assembly of tetrahedral blocks with bonded contacts. Material heterogeneity is modeled by varying the tensile strength at the block contacts. This grain-based rock model differs from previous disk/sphere particle-based rock models in its ability to represent a zero (or very low) initial porosity condition, as well as highly interlocked irregular block shapes that provide resistance to movement even after contact breakage. As a result, this model can reach higher uniaxial compressive strength to tensile strength ratios and larger friction coefficients than the disk/sphere particle-based rock model. The model captured the rock fragmentation process near the wellbore due to buckling and spalling. Thin fragments of rock similar to onion skins were produced, as observed in laboratory breakout experiments. The results suggest that this approach may be well suited to study the rock disaggregation process and other geomechanical problems in the rock excavation.

scholarly journals Models for evaluating craters morphology, relation of indentation hardness and uniaxial compressive strength via a flat-end indenter

2018 ◽  
Vol 10 (1) ◽  
pp. 289-296 ◽  
Author(s):  
Ligang Zhang ◽  
Xiao Fei Fu ◽  
G. R. Liu ◽  
Shi Bin Li ◽  
Wei Li ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Internal Friction ◽  
Uniaxial Compressive Strength ◽  
Poisson’S Ratio ◽  
Failure Process ◽  
Apex Angle ◽  
Poisson's Ratio ◽  
Percentage Error ◽  
Indentation Hardness ◽  
Angle Of Internal Friction

AbstractIn this work, the intensive theoretical study and laboratory tests are conducted to evaluate the craters morphology via the flat-ended indenter test, relationship of indentation hardness (HRI) and uniaxial compressive strength (UCS). Based on the stress distribution, failure process and Mohr–Coulomb failure criterion, the mathematical mechanical models are presented to express the formation conditions of “pulverized zone” and “volume break”. Moreover, a set of equations relating the depth and apex angle of craters, the ratio of indentation hardness and uniaxial compressive strength, the angle of internal friction and Poisson’s ratio are obtained. The depth, apex angle of craters and ratio of indentation hardness and uniaxial compressive strength are all affected by the angle of internal friction and Poisson’s ratio. The proposed models are also verified by experiments of rock samples which are cored from Da Qing oilfield, the percentage error between the test and calculated results for depth, apex angle of craters and the ratio of HRI and UCS are mainly in the range of –1.41%–8.92%, –5.91%–3.94% and –8.22%–13.22% respectively for siltstone, volcanic tuff, volcanic breccia, shale, sand stone and glutenite except mudstone, which demonstrates that our proposed models are robust and effective for brittle rock.

scholarly journals Size Effect of the Number of Parallel Joints on Uniaxial Compressive Strength and Characteristic Strength

Minerals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 62
Author(s):  
Gaojian Hu ◽  
Gang Ma ◽  
Jie Liu ◽  
Kuan Qi
Keyword(s):  
Numerical Simulation ◽  
Compressive Strength ◽  
Size Effect ◽  
Mathematical Models ◽  
Numerical Simulations ◽  
Uniaxial Compressive Strength ◽  
Special Functions ◽  
Characteristic Size ◽  
Characteristic Strength ◽  
Rock Size

The number of parallel joints has an impact on the size effect of the uniaxial compressive strength and characteristic strength of a rock; however, the relationships between them are yet to be derived. We studied the influence of the number of joints and rock size on the uniaxial compressive strength of the rock. This study established ten numerical simulation programs using numerical simulations and the RFPA software. Stress–strain curves of different numbers of parallel joints and sizes of rocks were analyzed. Relationships between the uniaxial compressive strength and number of parallel joints and rock size were proposed, and their special functions were obtained. Mathematical models between rock characteristic size, rock characteristic strength and the number of parallel joints were established. Simulations of the verification program confirmed that these relationships are still applicable after the angle of parallel joints changes.

The influence of the addition of ground olive stone on the thermo-mechanical behavior of compressed earth blocks

2020 ◽  
Vol 108 (2) ◽  
pp. 203
Author(s):  
Samia Djadouf ◽  
Nasser Chelouah ◽  
Abdelkader Tahakourt
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Mechanical Behavior ◽  
Agricultural Waste ◽  
Hydraulic Press ◽  
Dry Density ◽  
Olive Stone ◽  
Compressed Earth Blocks ◽  
Clay Matrix ◽  
Earth Blocks

Sustainable development and environmental challenges incite to valorize local materials such as agricultural waste. In this context, a new ecological compressed earth blocks (CEBS) with addition of ground olive stone (GOS) was proposed. The GOS is added as partial clay replacement in different proportions. The main objective of this paper is to study the effect of GOS levels on the thermal properties and mechanical behavior of CEB. We proceeded to determining the optimal water content and equivalent wet density by compaction using a hydraulic press, at a pressure of 10 MPa. The maximum compressive strength is reached at 15% of the GOS. This percentage increases the mechanical properties by 19.66%, and decreases the thermal conductivity by 37.63%. These results are due to the optimal water responsible for the consolidation and compactness of the clay matrix. The substitution up to 30% of GOS shows a decrease of compressive strength and thermal conductivity by about 38.38% and 50.64% respectively. The decrease in dry density and thermal conductivity is related to the content of GOS, which is composed of organic and porous fibers. The GOS seems promising for improving the thermo-mechanical characteristics of CEB and which can also be used as reinforcement in CEBS.

Sign in / Sign up

Export Citation Format

Share Document