Influence of Pyrolysis Temperature on the Gaseous Products of Lignite

2012 ◽  
Vol 524-527 ◽  
pp. 883-886 ◽  
Author(s):  
Chen Liang Zhou ◽  
Quan Sheng Liu ◽  
Yang Li ◽  
Ying Yue Teng ◽  
Ke Duan Zhi ◽  
...  
Keyword(s):  
Gas Chromatography ◽  
Pyrolysis Temperature ◽  
Volatile Matter ◽  
Calcium Sulfide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gaseous Products ◽  
Surface Moisture ◽  
Cracking Reaction ◽  
Temperature Programmed

Temperature-programmed pyrolysis of SL-lignite from Xilinhaote was investigated. The solid and gaseous pyrolysates were analyzed by means of gas chromatography(GC) and X-ray diffraction(XRD). The weight percents of surface moisture, ash, C, H and S increase with increasing the pyrolysis temperature in solid pyrolysates, while the volatile matter is contrary. The cracking reaction occurs before 600°C, the consolidation reaction happens between 600°C and 650°C, while the polycondensation or secondary reaction appears after 650°C. Calcium sulfide is formed by the process of decomposition of calcium sulphates at 900°C. The solid pyrolysates become more graphitic with increasing the pyrolysis temperature.

scholarly journals Impact of Pyrolysis Temperature on the Properties of Eucalyptus Wood-Derived Biochar

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5841
Author(s):  
Bruno Caio Chaves Fernandes ◽  
Kassio Ferreira Mendes ◽  
Ananias Francisco Dias Júnior ◽  
Vinícius Patrício da Silva Caldeira ◽  
Taliane Maria da Silva Teófilo ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electrical Conductivity ◽  
Scanning Electron Microscopy ◽  
Pyrolysis Temperature ◽  
Volatile Matter ◽  
Matter Content ◽  
X Ray Diffraction ◽  
X Ray ◽  
Eucalyptus Wood ◽  
Scanning Electron

Pyrolysis conditions directly influence biochar properties and, consequently, influence the potential use of biochar. In this study, we evaluated the effects of different pyrolysis temperatures (450, 550, 650, 750, 850, and 950 °C) on the hydrogen potential, electrical conductivity, ash content, yield, volatile matter content, elemental analysis, Fourier-transform infrared spectroscopy results, X-ray diffraction results, scanning electron microscopy results, specific surface area, and micropore volume of eucalyptus wood-derived biochar. The degree of linear association between pyrolysis temperatures and biochar properties was examined using the Pearson correlation coefficient. The results showed a positive correlation of the pyrolysis temperature with the hydrogen potential value, electrical conductivity, and elemental carbon. There was a negative correlation of the pyrolysis temperature with the yield, volatile matter content, elemental oxygen, elemental hydrogen, surface area, aromaticity, hydrophilicity, and polarity indexes. The Fourier-transform infrared spectroscopy data indicated an increase in aromaticity and a decrease in the polarity of high-temperature biochar. The increased pyrolysis temperature caused the loss of cellulose and crystalline mineral components, as indicated by X-ray diffraction analysis and scanning electron microscopy images. These results indicated that changing the pyrolysis temperature enables the production of biochar from the same raw material with a wide range of physicochemical properties, which allows its use in various types of agricultural and environmental activities.

scholarly journals Biodiesel Production on Monometallic Pt, Pd, Ru, and Ag Catalysts Supported on Natural Zeolite

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 48
Author(s):  
Pawel Mierczynski ◽  
Magdalena Mosińska ◽  
Lukasz Szkudlarek ◽  
Karolina Chalupka ◽  
Misa Tatsuzawa ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Natural Zeolite ◽  
Noble Metals ◽  
Methyl Esters ◽  
Physicochemical Characteristics ◽  
Biodiesel Production ◽  
X Ray Diffraction ◽  
X Ray ◽  
Yield Values ◽  
Temperature Programmed

Biodiesel production from rapeseed oil and methanol via transesterification reaction facilitated by various monometallic catalyst supported on natural zeolite (NZ) was investigated. The physicochemical characteristics of the synthesized catalysts were studied by X-ray diffraction (XRD), Brunauer–Emmett–Teller method (BET), temperature-programmed-reduction in hydrogen (H2-TPR), temperature-programmed-desorption of ammonia (NH3-TPD), Scanning Electron Microscope equipped with EDX detector (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) methods. The highest activity and methyl ester yields were obtained for the Pt/NZ catalyst. This catalyst showed the highest triglycerides conversion of 98.9% and fatty acids methyl esters yields of 94.6%. The activity results also confirmed the high activity of the carrier material (NZ) itself in the investigated reaction. Support material exhibited 90.5% of TG conversion and the Fatty Acid Methyl Esters yield (FAME) of 67.2%. Introduction of noble metals improves the TG conversion and FAME yield values. Increasing of the metal loading from 0.5 to 2 wt.% improves the reactivity properties of the investigated catalysts.

Selective catalytic reduction of NO by Co-Mn based nanocatalysts

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Vahid Zabihi ◽  
Mohammad Hasan Eikani ◽  
Mehdi Ardjmand ◽  
Seyed Mahdi Latifi ◽  
Alireza Salehirad
Keyword(s):  
Selective Catalytic Reduction ◽  
Catalytic Reduction ◽  
Energy Dispersive ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
X Ray ◽  
Analysis Techniques ◽  
Acidic Sites ◽  
Temperature Window ◽  
Temperature Programmed

Abstract One of the most significant aspects in selective catalytic reduction (SCR) of nitrogen oxides (NOx) is developing suitable catalysts by which the process occurs in a favorable way. At the present work SCR reaction by ammonia (NH3-SCR) was conducted using Co-Mn spinel and its composite with Fe-Mn spinel, as nanocatalysts. The nanocatalysts were fabricated through liquid routes and then their physicochemical properties such as phase composition, degree of agglomeration, particle size distribution, specific surface area and also surface acidic sites have been investigated by X-ray diffraction, Field Emission Scanning Electron Microscope, Energy-dispersive X-ray spectroscopy, energy dispersive spectroscopy mapping, Brunauer–Emmett–Teller, temperature-programmed reduction (H2-TPR) and temperature-programmed desorption of ammonia (NH3-TPD) analysis techniques. The catalytic activity tests in a temperature window of 150–400 °C and gas hourly space velocities of 10,000, 18,000 and 30,000 h−1 revealed that almost in all studied conditions, CoMn2O4/FeMn2O4 nanocomposite exhibited better performance in SCR reaction than CoMn2O4 spinel.

The Effect of Zinc Content on n-Pentane Isomerisation Over Zn–S2O82–/ZrO2–Al2O3 Catalyst

2017 ◽  
Vol 42 (1) ◽  
pp. 23-29
Author(s):  
Hua Song ◽  
Shengnan Li ◽  
Hualin Song ◽  
Feng Li ◽  
Huapeng Cui
Keyword(s):  
Zinc Content ◽  
Space Velocity ◽  
X Ray Diffraction ◽  
Sulfate Ions ◽  
X Ray ◽  
Weight Hourly Space Velocity ◽  
Mass Fractions ◽  
Crystallite Sizes ◽  
Temperature Programmed ◽  
Al2o3 Catalyst

A number of Zn–S2O82–/ZrO2–Al2O3 (Zn( x)–SZA) catalysts with different Zn mass fractions were synthesised and characterised by using X-ray diffraction, the Brunauer–Emmett–Teller method, and H2 temperature-programmed reduction. The structure and isomerisation performance of Zn( x)–SZA catalysts were studied using n-pentane as a probe reaction. The results showed that a pure tetragonal ZrO2 phase was formed on Zn( x)–SZA, and the ZrO2 crystallite sizes of the tetragonal phase increased in the order: Zn(0.5)–SZA < Zn(1.0)–SZA < Zn(1.5)–SZA < Zn(2.0)–SZA < SZA. Zn can strengthen the interaction between persulfate ions and the support, promote the formation of stronger acidity, lead to a better dispersion of sulfate ions on the surface, and improve the redox performance of the catalysts. The Zn(1.0)–SZA catalyst exhibited the best catalytic activity for n-pentane isomerisation. At a temperature of 170 °C, a reaction pressure of 2.0 MPa, a molar H2/ n-pentane ratio of 4:1, and a weight hourly space velocity of 1.0 h−1, the isopentane yield reached 58.0%.

scholarly journals Adsorción del naranja de metilo en solución acuosa sobre hidróxidos dobles laminares

2015 ◽  
Vol 25 (3) ◽  
pp. 25-34 ◽  
Author(s):  
Laura Alicia Ramírez Llamas ◽  
Araceli Jacobo Azuara ◽  
J. Merced Martínez Rosales
Keyword(s):  
Methyl Orange ◽  
Adsorption Capacity ◽  
Dye Adsorption ◽  
Temperature Programmed Desorption ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Suitable Temperature ◽  
Temperature Programmed ◽  
Double Hydroxides

In this paper, layered double hydroxides (LDH) were synthesized and characterized using techniques of Physisorption of Nitrogen, Infrared, Temperature Programmed Desorption, X-Ray Diffraction, TGA and Immersion Microcalorimetry, in order to determine the basic properties of the adsorbent. The methyl orange (MO) is used as a dye and as a result, it is frequently found in effluents from textile industries. The dye adsorption isotherms on LDH were studied as function of pH and temperature. The maximum adsorption capacity of methyl orange on LDH was carried out at pH 5, and the minimum adsorption capacity at pH 11, being 40.2 mg/g and 22.1 mg/g, respectively. Furthermore, the suitable temperature to promote the adsorption of methyl orange on LDH was at 25 °C, as at 35 °C shows a significant decrease. 

scholarly journals Effect of Zirconia Polymorph on Vapor-Phase Ketonization of Propionic Acid

Catalysts ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 768 ◽  
Author(s):  
Shuang Ding ◽  
Jiankang Zhao ◽  
Qiang Yu
Keyword(s):  
Propionic Acid ◽  
Vapor Phase ◽  
Surface Concentration ◽  
X Ray Diffraction ◽  
In Situ Drifts ◽  
X Ray ◽  
Surface Intermediates ◽  
Temperature Programmed ◽  
Diffuse Reflectance Infrared

Vapor-phase ketonization of propionic acid derived from biomass was studied at 300–375 °C over ZrO2 with different zirconia polymorph. The tetragonal ZrO2 (t-ZrO2) are more active than monoclinic ZrO2 (m-ZrO2). The results of characterizations from X-ray diffraction (XRD) and Raman suggest m-ZrO2 and t-ZrO2 are synthesized by the solvothermal method. NH3 and CO2 temperature-programmed desorption (NH3-TPD and CO2-TPD) measurements show that there were more medium-strength Lewis acid base sites with lower coordination exposed on m-ZrO2 relative to t-ZrO2, increasing the adsorption strength of propionic acid. The in situ DRIFTS (Diffuse reflectance infrared Fourier transform spectroscopy) of adsorbed propionic acid under ketonization reaction reveal that as the most abundant surface intermediates, the monodentate propionates are more active than bidentate propionates. In comparison with m-ZrO2, the t-ZrO2 surface favors monodentate adsorption over bidentate adsorption. Additionally, the adsorption strength of monodentate propionate is weaker on t-ZrO2. These differences in adsorption configuration and adsorption strength of propionic acid are affected by the zirconia structure. The higher surface concentration and weaker adsorption strength of monodentate propionates contribute to the higher ketonization rate in the steady state.

scholarly journals Ce- and Y-Modified Double-Layered Hydroxides as Catalysts for Dry Reforming of Methane: On the Effect of Yttrium Promotion

Catalysts ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 56 ◽  
Author(s):  
Katarzyna Świrk ◽  
Magnus Rønning ◽  
Monika Motak ◽  
Patricia Beaunier ◽  
Patrick Da Costa ◽  
...  
Keyword(s):  
Textural Properties ◽  
Dry Reforming ◽  
Dry Reforming Of Methane ◽  
Side Reactions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Nickel Species

Ce- and Y-promoted double-layered hydroxides were synthesized and tested in dry reforming of methane (CH4/CO2 = 1/1). The characterization of the catalysts was performed using X-ray fluorescence (XRF), X-ray diffraction (XRD), N2 sorption, temperature-programmed reduction in H2 (TPR-H2), temperature-programmed desorption of CO2 (TPD-CO2), H2 chemisorption, thermogravimetric analysis coupled by mass spectrometry (TGA/MS), Raman, and high-resolution transmission electron microscopy (HRTEM). The promotion with cerium influences textural properties, improves the Ni dispersion, decreases the number of total basic sites, and increases the reduction temperature of nickel species. After promotion with yttrium, the increase in basicity is not directly correlated with the increasing Y loading on the contrary of Ni dispersion. Dry reforming of methane (DRM) was performed as a function of temperature and in isothermal conditions at 700 °C for 5 h. For catalytic tests, a slight increase of the activity is observed for both Y and Ce doped catalysts. This improvement can of course be explained by Ni dispersion, which was found higher for both Y and Ce promoted catalysts. During DRM, the H2/CO ratio was found below unity, which can be explained by side reactions occurrence. These side reactions are linked with the increase of CO2 conversion and led to carbon deposition. By HRTEM, only multi-walled and helical-shaped carbon nanotubes were identified on Y and Ce promoted catalysts. Finally, from Raman spectroscopy, it was found that on Y and Ce promoted catalysts, the formed C is less graphitic as compared to only Ce-based catalyst.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

scholarly journals Study of Chemical and Morphological Transformations during Ni2Mo3N Synthesis via an Oxide Precursor Nitration Route

Catalysts ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 436
Author(s):  
Denis Leybo ◽  
Dmitry Arkhipov ◽  
Konstantin Firestein ◽  
Denis Kuznetsov
Keyword(s):  
Weight Changes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Oxide Precursor ◽  
Nitride Formation ◽  
Extended Surface ◽  
Temperature Programmed ◽  
Morphological Transformations ◽  
Physical And Chemical ◽  
Oxide Sample

Chemical and morphological transformations during Ni2Mo3N synthesis were studied in this work. Nitride samples were synthesized from oxide precursors in H2/N2 flow and were analyzed by thermogravimetry, X-ray diffraction analysis, scanning electron microscopy, and energy dispersive X-ray spectroscopy methods. In addition, physical and chemical adsorption properties were studied using low-temperature N2 physisorption and NH3 temperature-programmed desorption. It was shown that nitride formation proceeds through a sequence of phase transformations: NiMoO4 + MoO3 → Ni + NiMo + MoO2 → Ni + NiMo + Mo2N → Ni2Mo3N. The weight changes that were calculated from the proposed reactions were in agreement with the experimental data from thermogravimetry. The morphology of the powder changed from platelets and spheres for the oxide sample, to aggregates of needle-like particles for the intermediate product, to porous particles with an extended surface area for the nitride final product. The obtained results should prove useful for subsequent Ni2Mo3N based catalysts production process optimization.

scholarly journals Nanosized V-Ce Oxides Supported on TiO2 as a Superior Catalyst for the Selective Catalytic Reduction of NO

Catalysts ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 202
Author(s):  
Long Lu ◽  
Xueman Wang ◽  
Chunhua Hu ◽  
Ying Liu ◽  
Xiongbo Chen ◽  
...  
Keyword(s):  
Low Temperature ◽  
Selective Catalytic Reduction ◽  
Photoelectron Spectroscopy ◽  
Catalytic Reduction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Redox Capacity ◽  
Scr Of No ◽  
Temperature Programmed

Nanosized V-Ce oxides supported on TiO2 (VCT) were prepared and utilized in the low-temperature selective catalytic reduction (SCR) of NO with NH3. Compared with the other V-Ce oxides-based catalysts supported on Al2O3, ZrO2, and ZSM-5, VCT showed the best SCR activity in a low-temperature range. The NOx conversion of 90% could be achieved at 220 °C. Characterizations including X-ray diffraction (XRD), scanning election micrograph (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption with NH3 (NH3-TPD), and temperature-programmed reduction with H2 (H2-TPR) showed that V1.05Ce1/TiO2 exhibited a good dispersion of V2O5, enrichment of surface Ce3+ and chemical-absorbed oxygen, and excellent redox capacity and acidity, which resulted in the best SCR performance at low temperature.

Sign in / Sign up

Export Citation Format

Share Document