Research on the Strength of High-Strength Steel Slag Concrete with Skeleton Coarse Aggregate Gradation

2013 ◽  
Vol 671-674 ◽  
pp. 1918-1922
Author(s):  
Yi Zhou Zhuang ◽  
Er Bu Tian ◽  
Yue Zong Lian
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Coarse Aggregate ◽  
Concrete Strength ◽  
Steel Slag ◽  
High Strength ◽  
Test Results ◽  
Aggregate Gradation ◽  
Cement Ratio ◽  
Water Cement Ratio

Generally the high density in high-strength concrete results in high strength, and so people often mix superplasticizer and particulate to increase the density of concrete, but ignoring the effect of coarse aggregate gradation on concrete strength. Referring to several Gradation Theories, this paper selects the coarse aggregate gradation with skeleton, uses uniform design method to test the compressive strength of high-strength concrete, and analyses the test results. It can be known from the test results of 7d and 28d concrete specimen that the concrete strength decreases linearly with water-cement ratio and sand ratio; The 7d’s concrete strength has higher variability due to low water-cement ratio with superplasticizer; The coarse aggregate skeleton is interfered by the increase of steel slag and sand rate, and the concrete strength decreases with limited cement paste. Furthermore, the steel slag with less than 30% addition has little effect on concrete strength and it can increase the cement’s possibility of contacting to water, and reduce the amount of cement without lowering the concrete strength. The influential degree on the compressive strength of concrete is followed by ascending sequence of steel slag content, sand ratio and water-cement.

Experimental Research on the Influence of Pebble Aggregate Gradation on Concrete Strength

2013 ◽  
Vol 438-439 ◽  
pp. 179-182
Author(s):  
Xiu Hai Yin ◽  
Ling Lu
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Experimental Research ◽  
Bending Strength ◽  
Coarse Aggregate ◽  
Concrete Strength ◽  
Test Results ◽  
Aggregate Gradation ◽  
Cement Ratio ◽  
Maximal Size

By changing the grading of pebble and water cement ratio, the influence of pebble grading on the compressive strength and flexural strength of concrete is studied at the same pebble content. Test results show that the compression strength and bending strength of concrete decrease with the increasing of the maximal size of coarse aggregate, while the maximal size (Dmax) of pebble aggregate achieves 10mm, 20mm, 40mm and 60mm. And concrete strength decreases significantly when Dmax is 60mm. Meanwhile, the influence of aggregate gradation is obviously with the increase of age time.

Study on the Workability of High Strength Concrete with the Grading of Coarse Aggregate Skeleton Structure

2011 ◽  
Vol 261-263 ◽  
pp. 411-415
Author(s):  
Er Bu Tian ◽  
Feng Chao Wang ◽  
Ren Wei Zhang ◽  
Tao Ji
Keyword(s):  
High Strength Concrete ◽  
Coarse Aggregate ◽  
Concrete Strength ◽  
Uniform Design ◽  
Steel Slag ◽  
High Strength ◽  
Mineral Admixtures ◽  
Strength Concrete ◽  
Sand Surface ◽  
Skeleton Structure

People often use superplasticizer and mineral admixtures (such as steel slag, slag, etc.) to increase the density of concrete and improve concrete strength, but don’t use coarse aggregate gradding. The paper selects the coarse aggregate of skeleton structure from several grading concept, and uses Uniform Design to test high strength concrete workability, and analyses results. It is shown from the results that the method of Uniform Design can significantly reduce the workload, and concrete mixture slump increases linearly with the water-cement ratio and sand percentage, but decreases linearly with steel slag addition, and the water released from the flocculation of cement by superplasticizer can increase the slump, and most of water plays the role of lubricant before it reacts with cement, and the effect of slump that sand extends coarse aggregate skeleton are greater than that sand surface area increases.

Performance of Rubberized High Strength Concrete after Fire

2010 ◽  
Vol 163-167 ◽  
pp. 1403-1408
Author(s):  
Feng Liu ◽  
Gui Xuan Chen ◽  
Li Juan Li
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Test Results ◽  
Rubber Powder ◽  
Strength Concrete ◽  
Spalling Failure ◽  
Powder Content ◽  
Small Content

The effects of recycled rubber powder on working abilities, density and compressive strength of high strength concrete (HSC) at room temperature were studied in this paper. The characteristics of rubberized high strength concrete (RHSC) after fire was investigated by surface observation, weight loss and retained strength testing. The sieve number of rubber powder used in test is No.40 (420μm), No.60 (250µm) and No.80 (178µm), and the content of rubber powder filled in RHSC is 1%, 2%, 3% and 4% with respect to cementation material respectively. Test results show that the increase in rubber powder content reduces the concrete strength, while the decrease in compressive strength of RHSC is less than 10% when the content of rubber powder is within 2%. RHSC with small content of rubber (1%) can restrain the spalling failure of concrete under high temperature.

scholarly journals A Study on High Strength Concrete with Moderate Cement Content Incorporating Limestone Powder

2014 ◽  
Vol 61 (1) ◽  
pp. 43-58 ◽  
Author(s):  
Alaa M. Rashad ◽  
Hosam.El Din H. Seleem
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Coarse Aggregate ◽  
Cement Content ◽  
Drying Shrinkage ◽  
High Strength ◽  
Limestone Powder ◽  
Test Results ◽  
Strength Concrete ◽  
The Difference

Abstract This paper presents the results of an investigation to assess the validity of producing high strength concrete (HSC) using moderate cement content to reduce the consumption of the binders. Cement content is lowered from 500 kg/m3 to 400 kg/m3. The difference in cement content is compensated by the addition of fine limestone (LS) powder. Pozzolans were incorporated as an addition to cement. Different coarse aggregate types were employed. Workability, compressive strength, tensile strength, permeability and drying shrinkage were measured. Test results revealed that HSC with a compressive strength up to 79 MPa (at 90 days age) could be produced with moderate cement content. The mixtures consistency and drying shrinkage are greatly enhanced due to employing LS powder and the permeability is satisfactory. To provide better solution to some concrete disadvantages like cracking and drying shrinkage, using an economic rate for cement are believed to reduce these disadvantages.

Effects of Nano-CaCO3 on the Compressive Strength and Microstructure of High Strength Concrete in Different Curing Temperature

2011 ◽  
Vol 121-126 ◽  
pp. 126-131 ◽  
Author(s):  
Qing Lei Xu ◽  
Tao Meng ◽  
Miao Zhou Huang
Keyword(s):  
Compressive Strength ◽  
Low Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Strength Concrete ◽  
Calcium Nitrite ◽  
Orientation Index ◽  
Early Strength

In this paper, effects of nano-CaCO3 on compressive strength and Microstructure of high strength concrete in standard curing temperature(21±1°C) and low curing temperature(6.5±1°C) was studied. In order to improve the early strength of the concrete in low temperature, the early strength agent calcium nitrite was added into. Test results indicated that 0.5% dosage of nano-CaCO3 could inhibit the effect of calcium nitrite as early strength agent, but 1% and 2% dosage of nano-CaCO3 could improve the strength of the concrete by 13% and 18% in standard curing temperature and by 17% and 14% in low curing temperature at the age of 3days. According to the XRD spectrum, with the dosage up to 1% to 2%, nano-CaCO3 can change the orientation index significantly, leading to the improvement of strength of concrete both in standard curing temperature and low curing temperature.

Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

Deterioration of Mechanical Properties of High-Strength Pumpcrete after Exposure to High Temperatures

2010 ◽  
Vol 168-170 ◽  
pp. 564-569
Author(s):  
Guang Lin Yuan ◽  
Jing Wei Zhang ◽  
Jian Wen Chen ◽  
Dan Yu Zhu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Heating Rate ◽  
High Strength Concrete ◽  
Heating Temperature ◽  
High Strength ◽  
Air Cooling ◽  
Test Results ◽  
Strength Deterioration ◽  
Residual Compressive Strength

This paper makes an experimental study of mechanical properties of high-strength pumpcrete under fire, and the effects of heating rate, heating temperature and cooling mode on the residual compressive strength(RCS) of high-strength pumpcrete are investigated. The results show that under air cooling, the strength deterioration speed of high-strength concrete after high temperature increases with the increase of concrete strength grade. Also, the higher heating temperature is, the lower residual compressive strength value is. At the same heating rate (10°C/min), the residual compressive strength of C45 concrete after water cooling is a little higher than that after air cooling; but the test results are just the opposite for C55 and C65 concrete. The strength deterioration speed of high-strength concrete after high temperature increases with the increase of heating rate, but not in proportion. And when the heating temperature rises up between 200°C and 500°C, heating rate has the most remarkable effect on the residual compressive strength of concrete. These test results provide scientific proofs for further evaluation and analysis of mechanical properties of reinforced-concrete after exposure to high temperatures.

scholarly journals Influence of Aggregate Gradation on the Engineering Properties of Lightweight Aggregate Concrete

2018 ◽  
Vol 8 (8) ◽  
pp. 1324 ◽  
Author(s):  
How-Ji Chen ◽  
Chung-Hao Wu
Keyword(s):  
Compressive Strength ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Engineering Properties ◽  
Lightweight Aggregate Concrete ◽  
Aggregate Gradation ◽  
Aggregate Concrete ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Expanded Shale

Expanded shale lightweight aggregates, as the coarse aggregates, were used to produce lightweight aggregate concrete (LWAC) in this research. At the fixed water-cement ratio, paste quantity, and aggregate volume, the effects of various aggregate gradations on the engineering properties of LWAC were investigated. Comparisons to normal-weight concrete (NWC) made under the same conditions were carried out. From the experimental results, using normal weight aggregates that follow the specification requirements (standard gradation) obtained similar NWC compressive strength to that using uniform-sized aggregates. However, the compressive strength of LWAC made using small uniform-sized aggregates was superior to that made from standard-grade aggregates. This is especially conspicuous under the low water-cement ratio. Even though the workability was affected, this problem could be overcome with developed chemical additive technology. The durability properties of concrete were approximately equal. Therefore, it is suggested that the aggregate gradation requirement of LWAC should be distinct from that of NWC. In high strength LWAC proportioning, following the standard gradation suggested by American Society for Testing and Materials (ASTM) is optional.

Estimation of Compressive Strength of Recycled Aggregate High Strength Concrete Using Ultrasonic Pulse Velocity

2014 ◽  
Vol 605 ◽  
pp. 147-150
Author(s):  
Seong Uk Hong ◽  
Seung Hun Kim ◽  
Yong Taeg Lee
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Coarse Aggregate ◽  
High Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Recycled Aggregate ◽  
Strength Concrete ◽  
Recycled Coarse Aggregate

This study used the ultrasonic pulse velocity method, one of the non-destructive test methods that does not damage the building for maintenance of to-be-constructed concrete structures using recycled aggregates in order to estimate the compressive strength of high strength concrete structure using recycled coarse aggregate and provide elementary resources for technological establishment of ultrasonic pulse velocity method. 200 test pieces of high strength concrete 40, 50MPa using recycled coarse aggregate were manufactured by replacement rates (0, 30, 50, 100%) and age (1, 7, 28, 180days), and air curing was executed to measure compressive strength and wave velocity. As the result of compressive strength measurement, the one with age of 180day and design strength of 40MPa was 43.69MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 42.82, 41.22, 37.35MPa, and 50MPa was 52.50MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 49.02, 46.66, 45.30MPa, and while it could be seen that the test piece substituted with recycled aggregate was found to have lower strength than the test piece with natural aggregate only, but it still reached the design strength to a degree. The correlation of compressive strength and ultrasonic pulse velocity was found and regression analysis was conducted. The estimation formula for compressive strength of high strength concrete using recycled coarse aggregate was found to be Fc=0.069Vp4.05, R2=0.66

scholarly journals Effect of Water Cement Ratios on Compressive Strength of Palm Kernel Shell Concrete

2019 ◽  
Vol 2 (Issue 1) ◽  
Author(s):  
A.O Adeyemi ◽  
M.A Anifowose ◽  
I.O Amototo ◽  
S.A Adebara ◽  
M.Y Olawuyi
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Palm Kernel ◽  
Hardened Concrete ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Palm Kernel Shell ◽  
Compressive Strength Of Concrete ◽  
Palm Kernel Shells

This study examined the effect of varying water cement ratio on the compressive strength of concrete produced using palm kernel shell (PKS) as coarse aggregate at different replacement levels. The replacement levels of coarse aggregate with palm kernel shells (PKS) were 0%, 25%, 50%, and 100% respectively. PKS concrete cubes (144 specimens) of sizes 150mm x 150mm x 150mm were cast and cured in water for 7, 14, 21 and 28 days respectively. A mix ratio of 1:2:4 was adopted with water-cement ratio of 0.45, 0.5, and 0.6 respectively while the batching was done by weight. Slump test was conducted on fresh concrete while compressive strength test was carried out on the hardened concrete cubes using a compression testing machine of 2000kN capacity. The result of tests on fresh concrete shows that the slump height of 0.45 water cement ratio (w/c) increases with an increase in PKS%. This trend was similar to 0.50 and 0.60 w/c. However, the compressive strength of concrete cube decreases with an increase in w/c (from 0.45 to 0.60) but increases with respect to curing age and also decreases with increase in PKS%. Concrete with 0.45 water-cement ratio possess the highest compressive strength. It was observed that PKS is not a good substitute for coarse aggregate in mix ratio 1:2:4 for concrete productions. Hence, the study suggest the use of chemical admixture such as superplasticizer or calcium chloride in order to improve the strength of palm kernel shells-concrete.

Sign in / Sign up

Export Citation Format

Share Document