Effect of Increasing Rudder Deflection on Rudder Inflow for LNG Vessel in Shallow Water

2013 ◽  
Vol 787 ◽  
pp. 495-500 ◽  
Author(s):  
Agoes Priyanto ◽  
Adi Maimun ◽  
Y.M. Ahmed ◽  
Y. Mohamed
Keyword(s):  
Flow Field ◽  
Shallow Water ◽  
Unstructured Mesh ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Navier Stokes ◽  
Stagnation Region ◽  
Ansys Fluent ◽  
Icem Cfd ◽  
Rudder Angle

This paper presents the rudder inflow including fully non-uniform wake on a deep drafted LNG vessel in shallow water. The Ansys Fluent v.6.2 software was used to solve Reynold Average Navier-Stokes (RANS) equations, and Icem CFD as a mesh generator. The modeling was conducted based on the B 5-88 type propeller, with a diameter (D) of 7.7 meters. The propeller was meshed using tetra unstructured mesh in a flow field based on 3-Dimension incompressible Navier-stokes solver. It was found in the propeller-to-rudder interaction that there was a slight drop of pressure at rudder leading edge of 00 rudder angle of attack (AoA). However, the dropped pressure was observed on its leading edge as the rudder angle of attack was increased to-70. The effect of increasing rudder deflection was generated by the flow around it and inflows moved over the rudder. This deflection effect continued to X/D=0.4; afterwards, a zero velocity appeared because of the flow encountered by the stagnation region.

Numerical Study on Control of Sunroof Buffeting

2021 ◽  
Vol 13 (2) ◽  
Author(s):  
K. Vijaykumar ◽  
S. Poonkodi ◽  
A.T. Sriram
Keyword(s):  
Numerical Study ◽  
Leading Edge ◽  
Dominant Frequency ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Ansys Fluent ◽  
Flow Modification ◽  
Numerical Result ◽  
Modification Technique ◽  
Commercial Solver

Sunroof has become one of the essential features of a luxury car, and it provides natural air circulation and good illumination into the car. But the primary problem associated with it is the buffeting noise which causes discomfort to the passengers. Though adequate studies were carried out on sunroof buffeting, efficient control techniques are needed to be developed from fundamental mechanism. To reduce the buffeting noise, flow modifications at the entrance of the sunroof is considered in this study. The internal portion of the car with sunroof is simplified into a shear driven open cavity, and two-dimensional numerical simulations are carried out using commercial solver, ANSYS Fluent. Reynolds averaged Navier-Stokes equation is used with the realizable k-? turbulence model. The unsteady numerical result obtained in this study is validated with the available experimental results for the dominant frequency. The prediction is good agreement with experiment. Flow modification technique is proposed to control the sunroof buffeting by implementing geometric modifications. A hump has been placed near the leading edge of the cavity which resulted in significant reduction of pressure oscillations. Parametric studies have been performed by varying the height of hump and the distance of hump from the leading edge. There is no prominent difference when the height of the hump is varied. As the distance of the hump from the leading edge is reduced, the sound pressure level decreases.

Investigation of aerodynamic coefficients at Mach 6 over conical, hemispherical and flat-face spiked body

2017 ◽  
Vol 121 (1245) ◽  
pp. 1711-1732 ◽  
Author(s):  
R. Kalimuthu ◽  
R. C. Mehta ◽  
E. Rathakrishnan
Keyword(s):  
Flow Field ◽  
Blunt Body ◽  
Angle Of Attack ◽  
Separated Flow ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Geometrical Parameters ◽  
Aerodynamic Coefficients ◽  
Aerodynamic Forces ◽  
Flow Field Characteristics

ABSTRACTA forward spike attached to a blunt body significantly alters its flow field characteristics and influences aerodynamic characteristics at hypersonic flow due to formation of separated flow and re-circulation region around the spiked body. An experimental investigation was performed to measure aerodynamic forces for spikes blunt bodies with a conical, hemispherical and flat-face spike at Mach 6 and at an angle-of-attack range from 0° to 8° and length-to-diameterL/Dratio of spike varies from 0.5 to 2.0, whereLis the length of the spike andDis diameter of blunt body. The shape of the leading edge of the spiked blunt body reveals different types of flow field features in the formation of a shock wave, shear layer, flow separation, re-circulation region and re-attachment shock. They are analysed with the help of schlieren pictures. The shock distance ahead of the hemisphere and the flat-face spike is compared with the analytical solution and is showing satisfactory agreement with the schlieren pictures. The influence of geometrical parameters of the spike, the shape of the spike tip and angle-of-attack on the aerodynamic coefficients are investigated by measuring aerodynamic forces in a hypersonic wind tunnel. It is found that a maximum reduction of drag of about 77% was found for hemisphere spike ofL/D= 2.0 at zero angle-of-attack. Consideration for compensation of increased pitching moment is required to stabilise the aerodynamic forces.

scholarly journals Active Control of a Stalled Airfoil Through Steady or Unsteady Actuation Jets

2015 ◽  
Vol 137 (9) ◽  
Author(s):  
V. G. Chapin ◽  
E. Benard
Keyword(s):  
Active Control ◽  
Computational Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Position Angle ◽  
Navier Stokes ◽  
Suction Surface ◽  
Parametric Studies ◽  
Naca 0012

The active control of the leading-edge (LE) separation on the suction surface of a stalled airfoil (NACA 0012) at a Reynolds number of 106 based on the chord length is investigated through a computational study. The actuator is a steady or unsteady jet located on the suction surface of the airfoil. Unsteady Reynolds-Averaged Navier–Stokes (URANS) equations are solved on hybrid meshes with the Spalart–Allmaras turbulence model. Simulations are used to characterize the effects of the steady and unsteady actuation on the separated flows for a large range of angle of attack (0 < α < 28 deg). Parametric studies are carried out in the actuator design-space to investigate the control effectiveness and robustness. An optimal actuator position, angle, and frequency for the stalled angle of attack α = 19 deg are found. A significant increase of the lift coefficient is obtained (+ 84% with respect to the uncontrolled reference flow), and the stall is delayed from angle of attack of 18 deg to more than 25 deg. The physical nonlinear coupling between the actuator position, velocity angle, and frequency is investigated. The critical influence of the actuator location relative to the separation location is emphasized.

scholarly journals A Parametric Design Method for Hybrid Airfoils for Icing Wind Tunnel Test

2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Zhao Li ◽  
Guang-jun Yang ◽  
Xiao-yan Tong ◽  
Feng Jiang
Keyword(s):  
Flow Field ◽  
Parametric Design ◽  
Design Method ◽  
Pressure Coefficient ◽  
Wind Tunnel Test ◽  
Leading Edge ◽  
Full Scale ◽  
Navier Stokes ◽  
Ice Accretion ◽  
Multiple Control

The size of aircraft models that can be tested in icing wind tunnels is limited by the dimensions of the facilities in present; it is an effective method to replace the large model with a hybrid airfoil to carry out the experiment. A design method of multiple control points for hybrid airfoil based on the similarity of flow field in the leading edge of airfoil is proposed. Aiming at generating the full-scale flow field and ice accretion on the leading edge, multiobjective genetic optimization algorithm is used to design the hybrid airfoil under different conditions by combining the airfoil parameterization and solution of spatial constraint. Pressure tests of hybrid airfoils are carried out and compared with the leading edge pressure of the corresponding full-scale airfoils. The design and experimental results show that the pressure coefficient deviation between the hybrid airfoils designed and the corresponding full-scale airfoil in the 15% chord length range of the leading edge is within 4%. Finally, the vortex distribution and ice accretion process of the two airfoils were simulated by the unsteady Reynolds-averaged-Navier–Stokes (URANS) equations and multistep ice numerical method; it is shown that the hybrid airfoil can provide the same vortex distribution and ice accretion with the full-scale airfoil.

scholarly journals Effect of Leading-Edge Bulges on Aerodynamic Characteristics of Bionic Wingsail

2021 ◽  
Author(s):  
Chen Li ◽  
Peiting Sun ◽  
Hongming Wang
Keyword(s):  
Stokes Equations ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Suction Surface ◽  
Ansys Fluent ◽  
Navier Stokes Equations ◽  
Extension Direction ◽  
Lift And Drag

The leading-edge bulges along the extension direction are designed on the marine wingsail. The height and the spanwise wavelength of the protuberances are 0.1c and 0.25c, respectively. At Reynolds number Re=5×105, the Reynolds Averaged Navier-Stokes equations are applied to the simulation of the wingsail with the bulges thanks to ANSYS Fluent finite-volume solver based on the SST K-ω models. The grid independence analysis is carried out with the lift and drag coefficients of the wingsail at AOA = 8° and AOA=20°. The results show that while the efficiency of the wingsail is reduced by devising the leading-edge bulges before stall, the bulges help to improve the lift coefficient of the wingsail when stalling. At AOA=22° under the action of the leading-edge tubercles, a convective vortex is formed on the suction surface of the modified wingsail, which reduces the flow loss. So the bulges of the wingsail can delay the stall.

A Study of the Flow Field Associated with a Steadily-Rolling Slender Delta Wing

1964 ◽  
Vol 68 (638) ◽  
pp. 106-110 ◽  
Author(s):  
J. K. Harvey
Keyword(s):  
Flow Field ◽  
Static Pressure ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Rolling Moment ◽  
Air Stream ◽  
Total Head ◽  
Theoretical Predictions ◽  
Attached Flow

SummaryIn this paper an experiment is described in which a detailed study was made of the flow field associated with a slender sharp-edged delta wing which was rolling steadily at zero angle of attack to an air stream. The investigation was made by performing two pressure surveys: first , one of the static pressure acting on the wing’s surface and second by measuring the total-head distribution in the neighbourhood of the wing. From the former the local rolling-moment coefficients, Clp, are evaluated and these are compared with the predictions for attached flow, thus assessing the contributions to the forces acting on the wing which arise as a consequence of the leading-edge separations. The second set of surveys is used to construct a picture of the flow-field details and this is compared with that known to occur on a similar wing when it is set at an angle of attack to the airstream. One interesting finding is that the secondary separation which appears to cause the discrepancy between the theoretical predictions and the measurements made on slender wings at incidence, is absent in this configuration and thus it is concluded that these data could be used for a more meaningful test of the theory.

Experimental and Computational Investigation of a Simplified Geometry of an Engine/Pylon/Wing Installation at High-Lift Flight Conditions

2013 ◽  
Author(s):  
Matthieu Lucas ◽  
Yannick Bury ◽  
Cyril Bonnaud ◽  
Laurent Joly
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Longitudinal Vortex ◽  
Vortical Flow ◽  
Stream Velocity ◽  
Piv Measurements ◽  
Comprehensive Knowledge ◽  
Oil Flow

This paper focuses on the numerical and experimental characterization of the vortex structures that develop along a simplified geometry of a wing equipped with pylon-mounted engine at low speed/high angle of attack flight conditions. In these conditions, the presence of the engine installation under the wing induces a complex and unsteady vortical flow field at the nacelle/pylon/wing junctions which interacts with the upper wing boundary layer and leads to a drop of aircraft performances. In order to gain insight into the physics driving this interaction, it is proposed to isolate its fundamental mechanisms by simplifying the problem. The parameters of interest that led to the simplification of the model are first described. As a first step into a more comprehensive knowledge of this complex physics, this study is initially conducted at a Reynolds number of 200000, based on the chord wing and on the free stream velocity. Two configurations of angle of attack and sideslip angles (α = 8°/β = 0° and α = 8°/β = 30°) have been investigated. This work relies on unsteady RANS computations, oil flow visualizations and 3C-PIV measurements. The vortex dynamics thus produced is described in terms of vortex core position, intensity, size and turbulent intensity thanks to a vortex tracking post-processing algorithm. In addition, the analysis of the velocity flow field obtained from the PIV measurements will highlight the influence of the longitudinal vortex issued from the pylon/wing junction on the separation process of the boundary layer near the upper wing leading-edge.

An Integrated Particle-Tracking Impact/Adhesion Model for the Prediction of Fouling in a Subsonic Compressor

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
D. Borello ◽  
F. Rispoli ◽  
P. Venturini
Keyword(s):  
Leading Edge ◽  
Suction Side ◽  
Navier Stokes ◽  
Compressor Cascade ◽  
Deposit Formation ◽  
Stagnation Region ◽  
Vortical Structures ◽  
Tip Leakage ◽  
Eddy Simulation ◽  
Linear Compressor Cascade

The present paper reports on the analysis of the motion of adhesive particles and deposit formation in a 3D linear compressor cascade in order to investigate the fouling in turbomachinery flows. The unsteady flow field is provided by a prior hybrid large-eddy simulation (LES)/Reynolds-averaged Navier-Stokes (RANS) computation. The particles are individually tracked and the deposit formation is evaluated on the basis of the well-established Thornton and Ning model. Although the study is limited to three regions of the blade, where the most relevant turbulent phenomena occurs, the prediction of fouling shows good agreement with real situations. Deposits form near the casing and the hub, in the zones where there are strong vortical structures originated by the tip leakage and hub vortices. On the blade, the deposit analysis is focused on three main regions: (a) along the stagnation region on the leading edge; (b) on the suction side, where the particles are conveyed by the hub vortex towards blade surfaces; and (c) on the pressure side, where a clean zone forms between leading edge and the blade surface, as can be seen in real compressors.

On the Vortex Breakdown Phenomenon in High Angle of Attack Flows Over Delta Wing Geometries

2014 ◽  
Author(s):  
Eric D. Robertson ◽  
Varun Chitta ◽  
D. Keith Walters ◽  
Shanti Bhushan
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
High Angle ◽  
High Angle Of Attack ◽  
Eddy Simulation ◽  
Wing Model

Using computational methods, an investigation was performed on the physical mechanisms leading to vortex breakdown in high angle of attack flows over delta wing geometries. For this purpose, the Second International Vortex Flow Experiment (VFE-2) 65° sweep delta wing model was studied at a root chord Reynolds number (Recr) of 6 × 106 at various angles of attack. The open-source computational fluid dynamics (CFD) solver OpenFOAM was used in parallel with the commercial CFD solver ANSYS® FLUENT. For breadth, a variety of classic closure models were applied, including unsteady Reynolds-averaged Navier-Stokes (URANS) and detached eddy simulation (DES). Results for all cases are analyzed and flow features are identified and discussed. The results show the inception of a pair of leading edge vortices originating at the apex for all models used, and a region of steady vortical structures downstream in the URANS results. However, DES results show regions of massively separated helical flow which manifests after vortex breakdown. Analysis of turbulence quantities in the breakdown region gives further insight into the mechanisms leading to such phenomena.

Sign in / Sign up

Export Citation Format

Share Document