Effect of Ti, Al and Mg Addition on the Impact Toughness of Heat Affected Zone in Low Carbon Steel

2009 ◽  
Vol 79-82 ◽  
pp. 143-146
Author(s):  
Jiang Hua Ma ◽  
Dong Ping Zhan ◽  
Zhou Hua Jiang ◽  
Ji Cheng He
Keyword(s):  
Carbon Steel ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Low Carbon Steel ◽  
Optical Microscope ◽  
Carbon Steels ◽  
Low Carbon ◽  
Welding Simulation ◽  
Mg Addition ◽  
The Impact

In order to understand the effects of deoxidizer such as aluminium, titanium and magnesium on the impact toughness of heat affected zone (HAZ), three low carbon steels deoxidized by Ti-Al, Mg and Ti-Mg were obtained. After smelting, forging, rolling and welding simulation, the effects of Al, Ti and Mg addition on the impact toughness of HAZ in low carbon steel were studied. The inclusion characteristics (size, morphology and chemistry) of samples before welding and the fracture pattern of the specimens after the Charpy-type test were respectively analyzed using optical microscope and scanning electron microscopy (SEM). The following results were found. The density of inclusion in Ti-Mg deoxidized steel is bigger than Ti-Al deoxidized steel. The average diameter is decreased for the former than the latter. The addition of Ti-Mg can enhance the impact toughness of the HAZ after welding simulation. The maximal value of the impact toughness is 66.5J/cm2. The complex particles of MgO-TiOx-SiO2-MnS are most benefit to enhance impact toughness. The improvement of HAZ is attributable to the role of particle pinning and the formation of intergranular ferrite.

Effect of Ti, Zr and Mg Addition on the Impact Toughness of Heat Affected Zone in Low Carbon Steel

2010 ◽  
Vol 146-147 ◽  
pp. 1486-1490
Author(s):  
Jiang Hua Ma ◽  
Dong Ping Zhan ◽  
Zhou Hua Jiang ◽  
Ji Cheng He ◽  
Jin Yu
Keyword(s):  
Carbon Steel ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Low Carbon ◽  
Welding Simulation ◽  
Type Test ◽  
Titanium Zirconium ◽  
The Impact

In order to understand the effects of deoxidizer such as titanium, zirconium and magnesium on the impact toughness of heat affected zone (HAZ) of steel, four low carbon steels deoxidized by titanium, zirconium and magnesium were obtained. After smelting, forging, rolling and welding simulation, the effects of Ti, Zr and Mg additives on the impact toughness of HAZ in low carbon steel were studied. The inclusion characteristics (size, morphology and chemistry) analysis, Charpy-type test and the fracture observation of the specimens after the Charpy-type test were carried out respectively. The following results were found. The density of inclusion in Ti-Zr-Mg deoxidized steel is maximal. With the increasing of Ti content in steel, the proportion of inclusions in diameter less than 0.5 μm decreases. The proportion reaches maximum 64.0% in Ti-Zr-Mg deoxidized steel. The addition of Ti-Zr-Mg can enhance the impact toughness of HAZ after welding simulation. The maximal impacting energy is 249J at 253K. The complex particles of MgO-ZrO2-TiOx-MnS are most benefit to enhance impact toughness. The improvement of HAZ is attributable to the role of particle pinning and the formation of intergranular ferrite.

Effects of Al, Si and N Content on the Formation of M-A Constituent and HAZ Toughness of Ti-Containing Low-Carbon Steel

2021 ◽  
Vol 1016 ◽  
pp. 42-49
Author(s):  
Kook Soo Bang ◽  
Joo Hyeon Cha ◽  
Kyu Tae Han ◽  
Hong Chul Jeong
Keyword(s):  
Carbon Steel ◽  
Impact Toughness ◽  
Low Carbon Steel ◽  
Charpy Impact ◽  
Coarse Grained ◽  
Low Carbon ◽  
N Content ◽  
Si Content ◽  
The Impact ◽  
Haz Toughness

The present work investigated the effects of Al, Si, and N content on the impact toughness of the coarse-grained heat-affected zone (CGHAZ) of Ti-containing low-carbon steel. Simulated CGHAZ of differing Al, Si, and N contents were prepared, and Charpy impact toughness was determined. The results were interpreted in terms of microstructure, especially martensite-austenite (M-A) constituent. All elements accelerated ferrite transformation in CGHAZ but at the same time increased the amount of M-A constituent, thereby deteriorating CGHAZ toughness. It is believed that Al, Si, and free N that is uncombined with Ti retard the decomposition of austenite into pearlite and increase the carbon content in the last transforming austenite, thus increasing the amount of M-A constituent. Regardless of the amount of ferrite in CGHAZ, its toughness decreased linearly with an increase of M-A constituent in this experiment, indicating that HAZ toughness is predominantly affected by the presence of M-A constituent. When a comparison of the effectiveness is made between Al and Si, it showed that a decrease in Si content is more effective in reducing M-A constituents.

Developing High Strength-High Toughness Low Carbon Steel Using Combined V-Ti-Micro-Alloying and Different Thermo-Mechanical Treatments

2018 ◽  
Vol 786 ◽  
pp. 57-64 ◽  
Author(s):  
Ahmed Hamed ◽  
Mamdouh Eissa ◽  
Abdelhakim Kandil ◽  
Omnia Ali ◽  
Taha M. Mattar
Keyword(s):  
Tensile Strength ◽  
Carbon Steel ◽  
Impact Toughness ◽  
Low Carbon Steel ◽  
Chemical Compositions ◽  
Air Cooling ◽  
Low Carbon ◽  
Steel Alloys ◽  
Grain Sizes ◽  
The Impact

This work aims at designing and developing low carbon steel alloys to meet the high tensile strength, high ductility and high impact toughness properties. The effect of solid solution mechanism, precipitation hardening, as well as grain refinement were developed with different Manganese content (0.78-2.36wt%) combined with Vanadium(0.008-0.1wt%) and Titanium (0.002-0.072wt%) microalloying additions. The controlled thermo-mechanical treatments and chemical compositions play a big role in developing the microstructure and the corresponding mechanical properties. Therefore, the studied chemical compositions were treated thermo-mechanically by two different ways of changing start and finish forging temperatures with subsequent air cooling. The first way by start forging from 1050 to 830oC and the second from 950 to730oC. The second way of forging process developed finer grain sizes and higher ultimate tensile strengths for all the studied steel alloys. In spite of finer grain sizes, the impact toughness value was lower in the second regime due to detrimental influence of precipitation strengthening in the ferrite. A combination of 544 MPa yield strength, 615 MPa ultimate tensile strength, 20% elongation and 138 Joule impact toughness has been attained.

Retained Austenite Control and Extra-Cryogenic Impact Toughness of Fe-3.0%Mn Low Carbon Steel

2020 ◽  
Vol 993 ◽  
pp. 520-525
Author(s):  
Xiang Tao Deng ◽  
Xiao Lin Li ◽  
Long Huang ◽  
Zhao Dong Wang
Keyword(s):  
Heat Treatment ◽  
Carbon Steel ◽  
Low Temperature ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Uniform Elongation ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Low Temperature Impact Toughness ◽  
The Impact

The control of the retained austenite in Fe-3.0%Mn Low carbon steel by a three-step intercritical heat treatment and the low-temperature impact toughness evolution during the process were analyzed in the present study. The results indicated that the microstructure consisted intercritical ferrite, martensite/bainite and retained austenite. The distribution of carbon and manganese could improve the stability of the austenite located at the grain boundaries of prior austenite and lath boundaries of martensite. For the TRIP effect of the austenite, the excellent plasticity and low temperature toughness was obtained. The impact toughness could reach 200 J (impact energy) at －80 °C during the three-step heat treatment, and the uniform elongation could exceed at 16%.

Effect of Soaking Time on Paste Carburizing of Carburized Low Carbon Steel

2017 ◽  
Vol 740 ◽  
pp. 93-99
Author(s):  
Muhammad Hafizuddin Jumadin ◽  
Bulan Abdullah ◽  
Muhammad Hussain Ismail ◽  
Siti Khadijah Alias ◽  
Samsiah Ahmad
Keyword(s):  
Carbon Steel ◽  
Carbon Content ◽  
Low Carbon Steel ◽  
Case Depth ◽  
Carbon Steels ◽  
Low Carbon ◽  
Soaking Time ◽  
Low Carbon Steels ◽  
Carburized Steel ◽  
Carburizing Process

Increase of soaking time contributed to the effectiveness of case depth formation, hardness properties and carbon content of carburized steel. This paper investigates the effect of different soaking time (7-9 hours) using powder and paste compound to the carburized steel. Low carbon steels were carburized using powder and paste compound for 7, 8 and 9 hours at temperature 1000°C. The transformation of microstructure and formation carbon rich layer was observed under microscope. The microhardness profiles were analyzed to investigate the length of case depth produced after the carburizing process. The increment of carbon content was considered to find the correlation between types of carburizing compound with time. Results shows that the longer carburized steel was soaked, the higher potential in formation of carbon rich layer, case depth and carbon content, which led to better hardness properties for carburized low carbon steel. Longer soaking time, 9 hours has a higher dispersion of carbon up to 41%-51% compare to 8 hours and 7 hours. By using paste carburizing, it has more potential of carbon atom to merge the microstructure to transform into cementite (1.53 wt% C) compare to powder (0.97 wt% C), which increases the hardness of carburized steel (13% higher).

Predicting the Effects of Cold Working on the Machining Characteristics of Low Carbon Steels

1987 ◽  
Vol 109 (3) ◽  
pp. 257-264 ◽  
Author(s):  
E. M. Kopalinsky ◽  
P. L. B. Oxley
Keyword(s):  
Flow Stress ◽  
Carbon Steel ◽  
Cutting Forces ◽  
Cold Working ◽  
Low Carbon Steel ◽  
Carbon Steels ◽  
Low Carbon ◽  
Low Carbon Steels ◽  
Steel Work ◽  
Machining Characteristics

Experiments show that the cold working of low carbon steel work materials can improve their machinability by reducing cutting forces and improving surface finish and tool life. The somewhat paradoxical result of reducing cutting forces by cold working a material so that its hardness is increased is explained in this paper by using a machining theory which takes account of the flow stress properties of the work material and can thus allow for the effects of cold working.

Corrosion Behavior of Al-Si-Cr-Cu Bearing Low Carbon Steel in A Cyclic Dry/Wet Laboratory Test

2009 ◽  
Vol 79-82 ◽  
pp. 1017-1020 ◽  
Author(s):  
Hui Shu Zhang ◽  
Dong Ping Zhan ◽  
Song Lian Bai ◽  
Zhou Hua Jiang
Keyword(s):  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Low Carbon Steel ◽  
Optical Microscope ◽  
Low Carbon ◽  
Rust Layer ◽  
Electrochemical Behaviors ◽  
Corrosion Rates ◽  
The Matrix ◽  
Corrosion Behaviors

The corrosion behaviors of Al-Si-Cr-Cu bearing low carbon steel and a reference steel Q235 were tested in a cyclic dry/wet environment containing 0.01mol/L NaHSO3 in laboratory. Rust layers were observed by optical microscope (OM), scanning electron microscopy (SEM) and XRD. The electrochemical behaviors of the steels were studied on the polarization curves and electrochemical impedance spectroscopy (EIS). The results indicate that after 120h corrosion test, the annual corrosion rates of the designed steels reduce 42 % than Q235 at least. The corrosion products are generally iron oxyhydroxides and oxides such as FeOOH, γ-FeOOH, α-FeOOH, γ-Fe2O3, Fe3O4. The α-FeOOH possesses good stabilization mainly exits and can improve the corrosion resistance. There are the enrichments of Cu, Cr, Si and Al in the rust layer close to the matrix, which make the rust layer be more compact and protected. The corrosion currents of the two designed steels are lower than that of Q235, the corrosion potentials are higher than that of Q235 after Tafel fitting. The rust layer impedances of the designed steels are higher than that of Q235.

scholarly journals Microstructure and Properties of Heat Affected Zone in High-Carbon Steel after Welding with Fast Cooling in Water

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5059
Author(s):  
Michail Nikolaevich Brykov ◽  
Ivan Petryshynets ◽  
Miroslav Džupon ◽  
Yuriy Anatolievich Kalinin ◽  
Vasily Georgievich Efremenko ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
High Carbon Steel ◽  
Low Carbon Steel ◽  
Tensile Tests ◽  
Low Carbon ◽  
High Carbon ◽  
Mechanical Wear ◽  
Fast Cooling

The purpose of the research was to obtain an arc welded joint of a preliminary quenched high-carbon wear resistant steel without losing the structure that is previously obtained by heat treatment. 120Mn3Si2 steel was chosen for experiments due to its good resistance to mechanical wear. The fast cooling of welding joints in water was carried out right after welding. The major conclusion is that the soft austenitic layer appears in the vicinity of the fusion line as a result of the fast cooling of the welding joint. The microstructure of the heat affected zone of quenched 120Mn3Si2 steel after welding with rapid cooling in water consists of several subzones. The first one is a purely austenitic subzone, followed by austenite + martensite microstructure, and finally, an almost fully martensitic subzone. The rest of the heat affected zone is tempered material that is heated during welding below A1 critical temperature. ISO 4136 tensile tests were carried out for the welded joints of 120Mn3Si2 steel and 09Mn2Si low carbon steel (ASTM A516, DIN13Mn6 equivalent) after welding with fast cooling in water. The tests showed that welded joints are stronger than the quenched 120Mn3Si2 steel itself. The results of work can be used in industries where the severe mechanical wear of machine parts is a challenge.

Sign in / Sign up

Export Citation Format

Share Document