Effects of Parameters on Surface Roughness of Metal Parts by Selective Laser Melting

2013 ◽  
Vol 834-836 ◽  
pp. 872-875 ◽  
Author(s):  
Qun Qin ◽  
Guang Xia Chen
Keyword(s):  
Surface Roughness ◽  
Power Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Processing Parameters ◽  
Laser Power Density ◽  
Laser Melting ◽  
Scanning Velocity ◽  
Metal Parts ◽  
Overlap Ratio

The primary goal of this research is the effects of laser process parameters on surface roughness of metal parts built by selective laser melting. The main processing parameters used to control the surface roughness of melted layers are laser power, scanning velocity and overlap ratio. In our work, an orthogonal experimental design was employed to find the changing rules of the surface roughness through changing SLM processing parameters. The results show that the overlap ratio is the most important factor to affect the surface roughness. When the overlap ratio is below 50%, the surface roughness value of melted layers will decrease with laser power density increasing. When the overlap ratio is higher than or equal to 50%, the surface roughness value increases with the laser power density increasing. The optimal parameters of laser power 143W, scanning velocity 5m/min and overlap ratio 30% can be used to achieve melted layers with the best surface quality in our experiments, and the roughness value increases with slicing thickness increasing and the surface bias angle decreases.

scholarly journals Collaborative Optimization on Density and Surface Roughness of 316L Stainless Steel in Selective Laser Melting

2020 ◽  
Author(s):  
Yong Deng ◽  
Zhongfa Mao ◽  
Nan Yang ◽  
Xiaodong Niu ◽  
Xiangdong Lu
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Collaborative Optimization ◽  
Laser Melting

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

Molecular Dynamics Study of Laser and Plasma Nitriding of Titanium

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Hanjiang Yu ◽  
Tianya Tan ◽  
Wei Wu ◽  
Chao Tian ◽  
Ying An ◽  
...  
Keyword(s):  
Molecular Dynamics ◽  
Power Density ◽  
Laser Power ◽  
Plasma Nitriding ◽  
Processing Parameters ◽  
Nitride Layer ◽  
Laser Power Density ◽  
Experimental Results ◽  
Good Qualitative Agreement ◽  
Scanning Velocity

The molecular dynamics (MD) method is successfully applied to simulate the nitridation of titanium by the mixing technology with laser and plasma. Based on the simulation, the influence of the processing parameters, such as the laser power density and the scanning velocity on the effective thickness of the nitride layer, was investigated. It was found that, for each scanning velocity, there is a laser power density range within which the higher laser power density has the beneficial effect for nitriding treatment. Comparing the simulation and experimental results shows that the calculated results are in good qualitative agreement with the experimental results.

scholarly journals Collaborative Optimization of Density and Surface Roughness of 316L Stainless Steel in Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1601 ◽  
Author(s):  
Yong Deng ◽  
Zhongfa Mao ◽  
Nan Yang ◽  
Xiaodong Niu ◽  
Xiangdong Lu
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Collaborative Optimization ◽  
Laser Melting

Although the concept of additive manufacturing has been proposed for several decades, momentum in the area of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization during SLM to obtain high relative density and low surface roughness simultaneously in the literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. A statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. We observed that the laser power and scanning speed significantly affected the above objective quality, but the influence of the hatch spacing was comparatively low. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

Characterizing the Effect of Laser Power Density on Microstructure, Microhardness, and Surface Finish of Laser Deposited Titanium Alloy

2013 ◽  
Vol 135 (6) ◽  
Author(s):  
Rasheedat M. Mahamood ◽  
Esther T. Akinlabi ◽  
Mukul Shukla ◽  
Sisa Pityana
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Power Density ◽  
Surface Finish ◽  
Laser Power ◽  
Optical Microscope ◽  
Laser Power Density ◽  
Grain Structure ◽  
Selection Of

This paper reports the effect of laser power density on the evolving properties of laser metal deposited titanium alloy. A total of sixteen experiments were performed, and the microstructure, microhardness and surface roughness of the samples were studied using the optical microscope (OP), microhardness indenter and stylus surface analyzer, respectively. The microstructure changed from finer martensitic alpha grain to coarser Widmastätten alpha grain structure as the laser power density was increased. The results show that the higher the laser power density employed, the smoother the obtained surface. The microhardness initially increased as the laser power density was increased and then decreased as the power density was further increased. The result obtained in this study is important for the selection of proper laser power density for the desired microstructure, microhardness and surface finish of part made from Ti6Al4V.

Effect of processing parameters on forming defects during selective laser melting of AlSi10Mg powder

2020 ◽  
Vol 26 (5) ◽  
pp. 871-879 ◽  
Author(s):  
Haihua Wu ◽  
Junfeng Li ◽  
Zhengying Wei ◽  
Pei Wei
Keyword(s):  
Selective Laser Melting ◽  
Laser Power ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Argon Pressure ◽  
Powder Layer ◽  
Laser Melting ◽  
Content Type ◽  
Scan Speed ◽  
Forming Defects

Purpose To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting. Design/methodology/approach Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied. Findings The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified. Research limitations/implications The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample. Practical implications The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg, Social implications It can provide a technological support for 3D printing. Originality/value Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

Effects of the Processing Parameters on the Forming Quality of Stainless Steel Parts by Selective Laser Melting

2011 ◽  
Vol 189-193 ◽  
pp. 3668-3671 ◽  
Author(s):  
Qing Song Wei ◽  
Xiao Zhao ◽  
Li Wang ◽  
Rui Di Li ◽  
Jie Liu ◽  
...  
Keyword(s):  
Layer Thickness ◽  
Selective Laser Melting ◽  
Molten Pool ◽  
Laser Power ◽  
Single Layer ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Powder Layer ◽  
Laser Melting

Selective Laser Melting (SLM) can produce high-performance metal parts with complex structures. However, it’s difficult to control the processing parameters, because many factors involves. From the perspective of the molten pool, the study focuses on the effects of processing parameters, including scanning speed, laser power, scanning space, layer thickness, and scanning strategies, on the surface quality, the balling effect, the density of SLM parts, by conducting experiments of single track, single layer and block forming. The results show that the quality of the molten pool is affected by laser power and scanning speed. Scanning drove in the strategy of “jumping and turning”，a smooth surface and a less balling effect will be obtained. The thicker the powder layer is, the lower density will be obtained. The optimal parameters from series of experiments are: laser power of 98W; scanning speed of 90mm/s; scanning space of 0.07mm; layer thickness of 0.1mm; and scanning strategy of “jumping and turning”.

On Formation and Estimation of Pores during Selective Laser Melting of Single-Phase Metal Powders

2011 ◽  
Vol 338 ◽  
pp. 94-101
Author(s):  
Jin Hui Liu ◽  
Wen Juan Xie ◽  
Sheng Bing Xiao ◽  
Wei Ling Zhao ◽  
Jia Zhang
Keyword(s):  
Selective Laser Melting ◽  
Formation Mechanism ◽  
Single Phase ◽  
Porous Metal ◽  
Processing Parameters ◽  
Metal Powders ◽  
Porous Metals ◽  
Laser Melting ◽  
Metal Parts ◽  
Powder Particles

Porous metals are applied in many more fields than other porous materials. Pores in porous metal parts manufactured by selective laser melting (SLM) should not be regarded as defects but favorable characters because they are the main composition of porous metal parts. Therefore, fully densification is not the only target in forming metal parts via SLM. The formation mechanism of pores in SLM is studied mathematically in this article, and mathematical model is built to describe the formation mechanism. It is concluded that the shape of pores and the porosity of parts are the function of SLM processing parameters and the diameter of powder particles. Pores can be controlled and estimated by adjusting processing parameters and the nature of forming materials. Porous metal parts produced by SLM can be applied in many more fields owing that SLM technology is flexible to change the shape of these part and the nature of materials.

scholarly journals Investigation of Laser Polishing of Four Selective Laser Melting Alloy Samples

2020 ◽  
Vol 10 (3) ◽  
pp. 760
Author(s):  
Dongqi Zhang ◽  
Jie Yu ◽  
Hui Li ◽  
Xin Zhou ◽  
Changhui Song ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Layer By Layer ◽  
Metal Powders ◽  
Laser Melting ◽  
Laser Polishing

Selective laser melting (SLM) is a layer by layer process of melting and solidifying of metal powders. The surface quality of the previous layer directly affects the uniformity of the next layer. If the surface roughness value of the previous layer is large, there is the possibility of not being able to complete the layering process such that the entire process has to be abandoned. At least, it may result in long term durability problem and the inhomogeneity, may even make the processed structure not be able to be predicted. In the present study, the ability of a fiber laser to in-situ polish the rough surfaces of four typical additive-manufactured alloys, namely, Ti6Al4V, AlSi10Mg, 316L and IN718 was demonstrated. The results revealed that the surface roughness of the as-received alloys could be reduced to about 3 μm through the application of the laser-polishing process, and the initial surfaces had roughness values of 8.80–16.64 μm. Meanwhile, for a given energy density, a higher laser power produced a laser-polishing effect that was often more obvious, with the surface roughness decreasing with an increase in the laser power. Further, the polishing strategy will be optimized by simulation in our following study.

scholarly journals Selective Laser Melting Strategy for Fabrication of Thin Struts Usable in Lattice Structures

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1763 ◽  
Author(s):  
Radek Vrána ◽  
Daniel Koutný ◽  
David Paloušek ◽  
Libor Pantělejev ◽  
Jan Jaroš ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Laser Scanning ◽  
Laser Energy ◽  
Lattice Structure ◽  
Processing Parameters ◽  
Laser Melting ◽  
Contour Lines ◽  
Lower Porosity ◽  
Linear Laser

This paper deals with the selective laser melting (SLM) processing strategy for strut-lattice structure production which uses only contour lines and allows the porosity and roughness level to be managed based on combination of the input and linear energy parameters. To evaluate the influence of a laser scanning strategy on material properties and surface roughness a set of experiments was performed. The single welds test was used to find the appropriate processing parameters to achieve continuous welds with known width. Strut samples were used to find a suitable value of weld overlapping and to clarify the influence of input and linear laser energy on the strut porosity and surface roughness. The samples of inclined hollow struts were used to compare the wall thickness with single welds width; the results showed about 25% wider welds in the case of a hollow strut. Using the proposed SLM strategy it is possible to reach a significantly lower porosity and surface roughness of the struts. The best results for struts with an inclination of 35.26° were achieved with 25% track overlapping, input energy in the range from 9 J to 10.5 J and linear energy Elin from 0.25 to 0.4 J/mm; in particular, the relative density of 99.83% and the surface roughness on the side of the strut of Ra 14.6 μm in an as-built state was achieved.

Sign in / Sign up

Export Citation Format

Share Document