Electrical Resistivity of Fe-Bearing Sn1Ag0.5Cu Lead-Free Solder Alloys

2014 ◽  
Vol 895 ◽  
pp. 575-579
Author(s):  
Nur Aishah Aminah Mohd Amin ◽  
Dhafer Abdul Ameer Shnawah ◽  
Mohd Faizul Mohd Sabri ◽  
Suhana Binti Mohd Said
Keyword(s):  
Electrical Resistivity ◽  
Solder Alloy ◽  
Low Cost ◽  
Lead Free ◽  
Solder Alloys ◽  
Hazardous Element ◽  
Sac105 Solder ◽  
Free Solder ◽  
Lead Free Solders ◽  
Fe Addition

This paper reports on the effect of Fe addition in the range of 0.1 wt.% to 0.5 wt.% on the electrical resistivity of the Sn-1Ag-0.5Cu (SAC105) solder alloy. The electrical resistivity is characterized by the four-point probe technique. Results showed that the Fe-bearing SAC105 solder alloys exhibit lower electrical resistivity compared with the standard SAC105 solder alloy. Moreover, the electrical resistivity further decreases with increasing the amount of Fe addition. As Fe is a low-cost and non-hazardous element, along with the high mechanical reliability, the Fe-bearing SAC105 solder alloys also demonstrate good electrical characteristics, and hence may be an attractive candidate for a low cost, reliable formulation for lead free solders in electronics packaging.

Bismuth-Antimony as an Alternative for High Temperature Lead Free Solder

2012 ◽  
Vol 476-478 ◽  
pp. 1163-1168 ◽  
Author(s):  
M.Z. Shahrul Fadzli ◽  
M.A. Azmah Hanim ◽  
T. Sai Hong ◽  
A. Aidy ◽  
R. Rohaizuan
Keyword(s):  
High Temperature ◽  
Solder Alloy ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Bulk Analysis ◽  
Rich Phase ◽  
Solder Bulk ◽  
Free Solder ◽  
Lead Free Solders

The development works on high temperature lead free solder are mostly discussed nowadays. To replace the current high temperature lead free solders, further research need to be done. A great deal of effort has been put into the development of lead free solder alloys. Bi (Bismuth) and Sb (Antimony) solder system proved as one of the promising candidates for electronic assembly. Melting temperature of three Bi-Sb solder alloys studied in this research enhanced their potential as the alternative solder candidates for high temperature lead free solder. At interface, Cu3Sb IMC layer was formed for 95Bi-5Sb solder alloy. Spallation of Cu3Sb IMC layer took placed with the results of Cu3Sb IMC also found in the solder bulk. Analysis of 97.5Bi-2.5Sb solder alloy classified as no metallurgical reaction at the interface and only the mechanical joining existed at the interface. The dissolution of Cu from subtrate affected the formation of Cu rich phase and the unstable Bi-Cu rich phase phenomena act as the isothermal product found in solder bulk. Mechanical grain boundary grooving observed in 98.5Bi-1.5Sb solder alloys at interface. Different compositions of Bi-Sb solder alloys resulted in different types of microstructures at interface and in solder bulk after reflow.

Electrodeposition as an Alternative Route to Prepare Nanostructured Lead-Free Solder Alloy: A Short Review

2015 ◽  
Vol 1113 ◽  
pp. 554-559
Author(s):  
Sakinah Mohd Yusof ◽  
Md Amin Hashim ◽  
Junaidah Jai ◽  
Abdul Hadi
Keyword(s):  
Solder Alloy ◽  
Short Review ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Electronic Manufacturing ◽  
Melting Temperatures ◽  
Magnetization Density ◽  
Free Solder ◽  
Lead Free Solders

With world-wide strict legislation for reduction or removal of lead from industrial waste, development of a large number of lead-free alternative solder materials had been intensively examined. The drive for lead-free solders development was towards systems that can imitate conventional lead containing solder alloys in terms of melting temperatures and improvement of mechanical properties. Nanostructured solder alloy, with a grain size of typically < 100 nm, was a new class of materials with properties distinct from and frequently distinguished to those of the conventional alloy. In comparison, nanostructured solder alloys exhibit higher strength and hardness, enhanced diffusivity, and excellent soft and hard magnetic properties. Numerous different techniques were performed to synthesize these nanostructured solder alloys. Electrodeposition method has generated huge interest in nanostructured solder preparation, mainly due to its ability to deposit solders selectively and uniformly at nanoscale. These factors bring significant influences on the behaviors of products, such as magnetization, density, ductility, wear resistance, corrosion resistance, porosity, molecular structure, and crystal properties which plays a vital part in the field of electronic manufacturing. In this paper, a short review on the electrodeposition, a useful technique to deposit different metals and alloys, as a method for nanostructured lead-free solder alloys preparation is presented.

Fabrication and Properties of Lead-Free Sn-Ag-Cu-Ga Solder Alloy

2005 ◽  
Vol 475-479 ◽  
pp. 1747-1750 ◽  
Author(s):  
Guohai Chen ◽  
Ju Sheng Ma ◽  
Zhi Ting Geng
Keyword(s):  
Solder Alloy ◽  
Lead Free ◽  
Lead Free Solder ◽  
Electronic Industry ◽  
Solder Alloys ◽  
Cu Alloys ◽  
Lead Free Solder Alloy ◽  
Free Solder ◽  
Lead Free Solders ◽  
Electronic Assemblies

Sn-Pb solder alloys, widely used in electronic industry, will be restricted because of the toxicity of Pb. That is paramount importance that developing viable alternative lead-free solders for electronic assemblies. Sn-Ag-Cu alloys are better alternative because of its good performance. But they have a melting temperature of 217-225°C that is much higher than that of Sn-Pb eutectic alloy, 183°C. It may be very difficulty to realize industrialization. Sn-Ag-Cu-Ga solder alloys have been studied in this paper, including a series of properties tests, such as melting point, hardness, shear strength and solderability. The best composition of Sn-Ag-Cu-Ga lead-free solder alloy has been obtained.

Solder Joint Reliability of Sn-Cu and Sn-Ag-Cu Lead-Free Solder Alloys Solidified on Copper Substrates with Different Surface Roughnesses

2015 ◽  
Vol 830-831 ◽  
pp. 265-269
Author(s):  
Satyanarayan ◽  
K.N. Prabhu
Keyword(s):  
Solder Joint ◽  
Solder Matrix ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Cu Substrate ◽  
Cu Substrates ◽  
Free Solder ◽  
Substrate Surfaces ◽  
Lead Free Solders

In the present work, the bond strength of Sn-0.7Cu, Sn-0.3Ag-0.7Cu, Sn-2.5Ag-0.5Cu and Sn-3Ag-0.5Cu lead free solders solidified on Cu substrates was experimentally determined. The bond shear test was used to assess the integrity of Sn–Cu and Sn–Ag–Cu lead-free solder alloy drops solidified on smooth and rough Cu substrate surfaces. The increase in the surface roughness of Cu substrates improved the wettability of solders. The wettability was not affected by the Ag content of solders. Solder bonds on smooth surfaces yielded higher shear strength compared to rough surfaces. Fractured surfaces revealed the occurrence of ductile mode of failure on smooth Cu surfaces and a transition ridge on rough Cu surfaces. Though rough Cu substrate improved the wettability of solder alloys, solder bonds were sheared at a lower force leading to decreased shear energy density compared to the smooth Cu surface. A smooth surface finish and the presence of minor amounts of Ag in the alloy improved the integrity of the solder joint. Smoother surface is preferable as it favors failure in the solder matrix.

Nanoindentation Characterization of Lead-free Solders and Intermetallic Compounds under Thermal Aging

2010 ◽  
Vol 2010 (1) ◽  
pp. 000314-000318
Author(s):  
Tong Jiang ◽  
Fubin Song ◽  
Chaoran Yang ◽  
S. W. Ricky Lee
Keyword(s):  
Mechanical Properties ◽  
Thermal Aging ◽  
Solder Joints ◽  
Lead Free ◽  
Small Range ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Aging Test ◽  
Free Solder ◽  
Lead Free Solders

The enforcement of environmental legislation is pushing electronic products to take lead-free solder alloys as the substitute of traditional lead-tin solder alloys. Applications of such alloys require a better understanding of their mechanical behaviors. The mechanical properties of the lead-free solders and IMC layers are affected by the thermal aging. The lead-free solder joints on the pads subject to thermal aging test lead to IMC growth and cause corresponding reliability concerns. In this paper, the mechanical properties of the lead-free solders and IMCs were characterized by nanoindentation. Both the Sn-rich phase and Ag3Sn + β-Sn phase in the lead-free solder joint exhibit strain rate depended and aging soften effect. When lead-free solder joints were subject to thermal aging, Young's modulus of the (Cu, Ni)6Sn5 IMC and Cu6Sn5 IMC changed in very small range. While the hardness value decreased with the increasing of the thermal aging time.

Effect of Sb additions on the creep behaviour of low temperature lead-free Sn–8Zn–3Bi solder alloy

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Guang Ren ◽  
Maurice Collins
Keyword(s):  
Low Temperature ◽  
Solder Alloy ◽  
Creep Behaviour ◽  
Lead Free ◽  
Coefficient Of Determination ◽  
Secondary Creep ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Content Type ◽  
Free Solder

Purpose This paper aims to investigate the creep behaviour of the recently developed Sn–8Zn–3Bi–xSb (x = 0, 0.5, 1.0 and 1.5) low temperature lead-free solder alloys. Design/methodology/approach An in-house compressive test rig was developed to perform creep tests under stresses of 20–40 MPa and temperature range 25°C–75 °C. Dorn power law and Garofalo hyperbolic sine law were used to model the secondary creep rate. Findings High coefficient of determination R2 of 0.99 is achieved for both the models. It was found that the activation energy of Sn–8Zn–3Bi solder alloy can be significantly increased with addition of Sb, by 60% to 90 kJ/mol approximately, whereas the secondary creep exponent falls in the range 3–7. Improved creep resistance is attributed to solid solution strengthening introduced by micro-alloying. Creep mechanisms that govern the deformation of these newly developed lead-free solder alloys have also been proposed. Originality/value The findings are expected to fill the gap of knowledge on creep behaviour of these newly developed solder alloys, which are possible alternatives as lead-free interconnecting material in low temperature electronic assembly.

Impact of aluminium addition on the corrosion behaviour of Sn–1.0Ag–0.5Cu lead-free solder

RSC Advances ◽  
2015 ◽  
Vol 5 (120) ◽  
pp. 99058-99064 ◽  
Author(s):  
N. I. M. Nordin ◽  
S. M. Said ◽  
R. Ramli ◽  
K. Weide-Zaage ◽  
M. F. M. Sabri ◽  
...  
Keyword(s):  
Solder Alloy ◽  
Corrosion Behaviour ◽  
Corrosion Products ◽  
Lead Free ◽  
Lead Free Solder ◽  
Aluminium Addition ◽  
Sac105 Solder ◽  
Free Solder

(a) Al provides an enhanced passivation capability over SAC105 solder alloy. (b) Corrosion products on the surface consist of Al2CuO4, Al2O3, SnO and SnO2. (c) Al-added SAC105 is less susceptible to corrosion.

scholarly journals Phase equilibria investigation and alloys characterization in Sn-In-Ag system

2008 ◽  
Vol 62 (3) ◽  
pp. 148-152
Author(s):  
Aleksandra Milosavljevic ◽  
Dragana Zivkovic ◽  
Dragan Manasijevic ◽  
Nadezda Talijan ◽  
Aleksandar Grujic ◽  
...  
Keyword(s):  
Phase Equilibria ◽  
Xrd Analysis ◽  
Lead Free ◽  
Solder Alloys ◽  
Standard Lead ◽  
Free Solder ◽  
Dsc Method ◽  
Lead Free Solders ◽  
Thermocalc Software

Lead-free soldering has become very popular in the world recently, especially in electronics, because of high ecological demands in industry. Some of lead-free solder alloys are already used in electronic industry, but despite that investigations are still going in order to find suitable replacement for Pb-Sn standard solder. In this paper phase equilibria and characterization of Sn-In-Ag alloys in section In:Ag = 7:3 are investigated. The results of phase diagram calculation are obtained by ThermoCalc software, and characteristic temperatures by DSC method. The results of XRD analysis, optical microscopy, microhardness and electrical conductivity are also presented. These results are given in order to contribute the knowledge about lead-free solders, especially Sn-In-Ag solder alloys, which are potential candidates for replacement standard lead solders.

Physical and Mechanical Behaviors of SnCu-Based Lead-Free Solder Alloys with an Addition of Aluminium

2015 ◽  
Vol 815 ◽  
pp. 64-68 ◽  
Author(s):  
Nisrin Adli ◽  
Nurul Razliana Abdul Razak ◽  
Norainiza Saud
Keyword(s):  
Melting Point ◽  
Solder Alloy ◽  
Lead Free ◽  
Lead Free Solder ◽  
Mechanical Behaviors ◽  
Solder Alloys ◽  
Al Content ◽  
Homogenous Distribution ◽  
Lead Free Solder Alloy ◽  
Free Solder

The effect of Al addition on the microstructure, melting point and microhardness of SnCu-Al lead-free solder alloys were investigated with two different compositions of Al which were 1 wt% and 5 wt%. These solder alloys were fabricated through powder metallurgy (PM) method. The results showed that the melting point and the microhardness value of the SnCu-Al lead-free solder alloy were increased as the Al content increased from 1 wt% to 5 wt%. The grain growth of SnCu-Al lead-free solder alloy also tends to be retarded due to the homogenous distribution of Al at the grain boundaries.

scholarly journals Effects Of Nickel On The Microstructure And The Mechanical Properties Of Sn-0.7Cu Lead-Free Solders

2015 ◽  
Vol 60 (2) ◽  
pp. 1449-1454 ◽  
Author(s):  
A. Gyenes ◽  
A. Simon ◽  
P. Lanszki ◽  
Z. Gácsi
Keyword(s):  
Mechanical Properties ◽  
Morphological Evolution ◽  
Nickel Content ◽  
Lead Free ◽  
Solder Alloys ◽  
Nickel Addition ◽  
Free Solder ◽  
Ni Additions ◽  
Lead Free Solders ◽  
Addition Level

AbstractThis paper investigates the effects of small amount nickel addition (0, 200, 400, 800, 1800 ppm) on the microstructure and the mechanical properties of Sn-0.7Cu lead-free solder alloys. It is known that even ppm level Ni additions have significant effects on the microstructure of Sn-Cu solder alloys. Ni suppresses the growth ofβ-Sn dendrites in favour of eutectic formation. As the nickel content increases, the microstructure undergoes a morphological evolution from hypoeutectic through fully eutectic to hypereutectic. Along with these transformations, the mechanical properties of the alloy also significantly change. Based on the experimental results presented in this paper, the Sn-0.7Cu solder achieves maximum strength at the addition level of 800 ppm Ni, when the microstructure becomes fully eutectic.

Sign in / Sign up

Export Citation Format

Share Document