Nanoindentation Characterization of Lead-free Solders and Intermetallic Compounds under Thermal Aging

2010 ◽  
Vol 2010 (1) ◽  
pp. 000314-000318
Author(s):  
Tong Jiang ◽  
Fubin Song ◽  
Chaoran Yang ◽  
S. W. Ricky Lee
Keyword(s):  
Mechanical Properties ◽  
Thermal Aging ◽  
Solder Joints ◽  
Lead Free ◽  
Small Range ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Aging Test ◽  
Free Solder ◽  
Lead Free Solders

The enforcement of environmental legislation is pushing electronic products to take lead-free solder alloys as the substitute of traditional lead-tin solder alloys. Applications of such alloys require a better understanding of their mechanical behaviors. The mechanical properties of the lead-free solders and IMC layers are affected by the thermal aging. The lead-free solder joints on the pads subject to thermal aging test lead to IMC growth and cause corresponding reliability concerns. In this paper, the mechanical properties of the lead-free solders and IMCs were characterized by nanoindentation. Both the Sn-rich phase and Ag3Sn + β-Sn phase in the lead-free solder joint exhibit strain rate depended and aging soften effect. When lead-free solder joints were subject to thermal aging, Young's modulus of the (Cu, Ni)6Sn5 IMC and Cu6Sn5 IMC changed in very small range. While the hardness value decreased with the increasing of the thermal aging time.

Formation and Mechanical Properties of Intermetallic Compounds in Sn-Cu High-Temperature Lead-Free Solder Joints

2010 ◽  
Vol 654-656 ◽  
pp. 2450-2454 ◽  
Author(s):  
De Kui Mu ◽  
Hideaki Tsukamoto ◽  
Han Huang ◽  
Kazuhiro Nogita
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Intermetallic Compounds ◽  
Solder Joints ◽  
Nickel Content ◽  
Lead Free ◽  
Lead Free Solder ◽  
Nickel Addition ◽  
Free Solder ◽  
Lead Free Solders

High-temperature lead-free solders are important materials for electrical and electronic devices due to increasing legislative requirements that aim at reducing the use of traditional lead-based solders. For the successful use of lead-free solders, a comprehensive understanding of the formation and mechanical properties of Intermetallic Compounds (IMCs) that form in the vicinity of the solder-substrate interface is essential. In this work, the effect of nickel addition on the formation and mechanical properties of Cu6Sn5 IMCs in Sn-Cu high-temperature lead-free solder joints was investigated using Scanning Electron Microscopy (SEM) and nanoindentation. It was found that the nickel addition increased the elastic modulus and hardness of the (Cu, Ni)6Sn5. The relationship between the nickel content and the mechanical properties of the IMCs was also established.

Effect of aluminum content on structure, transport and mechanical properties of Sn-Zn eutectic lead free solder alloy rapidly solidified from melt.

2015 ◽  
Vol 10 (1) ◽  
pp. 2641-2648
Author(s):  
Rizk Mostafa Shalaby ◽  
Mohamed Munther ◽  
Abu-Bakr Al-Bidawi ◽  
Mustafa Kamal
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Lead Free ◽  
Al Alloy ◽  
Lead Free Solder ◽  
Pronounced Increase ◽  
Mass Unit ◽  
Size Refinement ◽  
Free Solder ◽  
Lead Free Solders

The greatest advantage of Sn-Zn eutectic is its low melting point (198 oC) which is close to the melting point. of Sn-Pb eutectic solder (183 oC), as well as its low price per mass unit compared with Sn-Ag and Sn-Ag-Cu solders. In this paper, the effect of 0.0, 1.0, 2.0, 3.0, 4.0, and 5.0 wt. % Al as ternary additions on melting temperature, microstructure, microhardness and mechanical properties of the Sn-9Zn lead-free solders were investigated. It is shown that the alloying additions of Al at 4 wt. % to the Sn-Zn binary system lead to lower of the melting point to 195.72 ˚C.  From x-ray diffraction analysis, an aluminium phase, designated α-Al is detected for 4 and 5 wt. % Al compositions. The formation of an aluminium phase causes a pronounced increase in the electrical resistivity and microhardness. The ternary Sn-9Zn-2 wt.%Al exhibits micro hardness superior to Sn-9Zn binary alloy. The better Vickers hardness and melting points of the ternary alloy is attributed to solid solution effect, grain size refinement and precipitation of Al and Zn in the Sn matrix.  The Sn-9%Zn-4%Al alloy is a lead-free solder designed for possible drop-in replacement of Pb-Sn solders.  

Solder Joint Reliability of Sn-Cu and Sn-Ag-Cu Lead-Free Solder Alloys Solidified on Copper Substrates with Different Surface Roughnesses

2015 ◽  
Vol 830-831 ◽  
pp. 265-269
Author(s):  
Satyanarayan ◽  
K.N. Prabhu
Keyword(s):  
Solder Joint ◽  
Solder Matrix ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Cu Substrate ◽  
Cu Substrates ◽  
Free Solder ◽  
Substrate Surfaces ◽  
Lead Free Solders

In the present work, the bond strength of Sn-0.7Cu, Sn-0.3Ag-0.7Cu, Sn-2.5Ag-0.5Cu and Sn-3Ag-0.5Cu lead free solders solidified on Cu substrates was experimentally determined. The bond shear test was used to assess the integrity of Sn–Cu and Sn–Ag–Cu lead-free solder alloy drops solidified on smooth and rough Cu substrate surfaces. The increase in the surface roughness of Cu substrates improved the wettability of solders. The wettability was not affected by the Ag content of solders. Solder bonds on smooth surfaces yielded higher shear strength compared to rough surfaces. Fractured surfaces revealed the occurrence of ductile mode of failure on smooth Cu surfaces and a transition ridge on rough Cu surfaces. Though rough Cu substrate improved the wettability of solder alloys, solder bonds were sheared at a lower force leading to decreased shear energy density compared to the smooth Cu surface. A smooth surface finish and the presence of minor amounts of Ag in the alloy improved the integrity of the solder joint. Smoother surface is preferable as it favors failure in the solder matrix.

Effect of Aging on the Properties of Intermetallic Layers in SAC+Bi Solder Joints

2021 ◽  
Author(s):  
Mohammad Ashraful Haq ◽  
Mohd Aminul Hoque ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Aging Condition ◽  
Sac305 Solder ◽  
The Poor ◽  
Free Solder ◽  
Lead Free Solders ◽  
Overall Reliability ◽  
Intermetallic Layers

Abstract A major problem faced by electronic packaging industries is the poor reliability of lead free solder joints. One of the most common methods utilized to tackle this problem is by doping the alloy with other elements, especially bismuth. Researches have shown Bismuth doped solder joints to mostly fail near the Intermetallic (IMC) layer rather than the bulk of the solder joint as commonly observed in traditional SAC305 solder joints. An understanding of the properties of this IMC layer would thus provide better solutions on improving the reliability of bismuth doped solder joints. In this study, the authors have used three different lead free solders doped with 1%, 2% and 3% bismuth. Joints of these alloys were created on copper substrates. The joints were then polished to clearly expose the IMC layers. These joints were then aged at 125 °C for 0, 1, 2, 5 and 10 days. For each aging condition, the elastic modulus and the hardness of the IMC layers were evaluated using a nanoindenter. The IMC layer thickness and the chemical composition of the IMC layers were also determined for each alloy at every aging condition using Scanning Electron Microscopy (SEM) and EDS. The results from this study will give a better idea on how the percentage of bismuth content in lead free solder affects the IMC layer properties and the overall reliability of the solder joints.

Influence of Indium and Antimony Additions on Mechanical Properties and Microstructure of Sn-3.0Ag-0.5Cu Lead Free Solder Alloys

2017 ◽  
Vol 266 ◽  
pp. 196-200 ◽  
Author(s):  
Suchart Chantaramanee ◽  
Phairote Sungkhaphaitoon ◽  
Thawatchai Plookphol
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Vickers Microhardness ◽  
Lead Free ◽  
Mechanical And Thermal Properties ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Sac305 Solder ◽  
Percent Elongation ◽  
Free Solder

In this research, we investigated the influence of indium and antimony additions on the microstructure, mechanical and thermal properties of Sn-3.0Ag-0.5Cu lead free solder alloys. The results revealed that the addition of 0.5 wt.%InSb into SAC305 solder alloys resulted to a reduced melting temperature by 3.8 °C and IMCs phases formed new Ag3(Sn,In) and SnSb in the Sn-rich matrix with a decreased grain size of 28%. These phases improved the mechanical properties of solder alloys. In addition, the mechanical properties of SAC305 solder alloys increased by adding 0.5 wt.%InSb, resulting in an increase of ultimate tensile strength of 24%, but the percent elongation decreased to 45.8%. Furthermore, the Vickers microhardness slightly increased of the SAC305 solder alloys.

Evolution of Lead Free Solder Material Behavior Under Elevated Temperature Aging

2007 ◽  
Author(s):  
Hongtao Ma ◽  
Jeffrey C. Suhling ◽  
Yifei Zhang ◽  
Pradeep Lall ◽  
Michael J. Bozack
Keyword(s):  
Elevated Temperature ◽  
Room Temperature ◽  
Solder Joints ◽  
Material Behavior ◽  
Lead Free ◽  
Lead Free Solder ◽  
Room Temperature Aging ◽  
Free Solder ◽  
Lead Free Solders ◽  
Temperature Aging

The microstructure, mechanical response, and failure behavior of lead free solder joints in electronic assemblies are constantly evolving when exposed to isothermal aging and/or thermal cycling environments. In our prior work on aging effects (Ma, et al., ECTC 2006), we demonstrated that the observed material behavior variations of SAC405 and SAC305 lead free solders during room temperature aging (25 °C) were unexpectedly large and universally detrimental to reliability. Such effects for lead free solder materials are much more dramatic at the higher aging temperatures (e.g. 100–150 °C) typical of the harsh environments present in high performance computing and in automotive, aerospace, and defense applications. However, there has been little work in the literature, and the work that has been done has concentrated on the degradation of solder ball shear strength (e.g. Dage Shear Tester). Current finite element models for solder joint reliability during thermal cycling accelerated life testing are based on traditional solder constitutive and failure models that do not evolve with material aging. Thus, there will be significant errors in the calculations with the new lead free SAC alloys that illustrate dramatic aging phenomena. In the current work, we have explored the effects of elevated temperature isothermal aging on the mechanical behavior and reliability of lead free solders. The effects of aging on mechanical behavior have been examined by performing stress-strain and creep tests on SAC405 and SAC305 samples that were aged for various durations (0–6 months) at several elevated temperatures (80, 100, 125, and 150 °C). Analogous tests were performed with 63Sn-37Pb eutectic solder samples for comparison purposes. Variations of the temperature dependent mechanical properties (elastic modulus, yield stress, ultimate strength, creep compliance, etc.) were observed and modeled as a function of aging time and temperature. In this paper, we have concentrated our efforts on presenting the results for samples aged at 125 °C. In addition, the new elevated temperature aging data were correlated with our room temperature results from last year’s investigation. The results obtained in this work have demonstrated the significant effects of elevated temperature exposure on solder joints. As expected, the mechanical properties evolved at a higher rate and experienced larger changes during elevated temperature aging (compared to room temperature aging). After approximately 200 hours of aging, the lead free solder joint material properties were observed to degrade at a nearly constant rate. We have developed a mathematical model to predict the variation of the properties with aging time and aging temperature. Our data for the evolution of the creep response of solders with elevated temperature aging show that the creep behavior of lead free and tin-lead solders experience a “crossover point” where lead free solders begin to creep at higher rates than standard 63Sn-37Pb solder for the same stress level. Such an effect is not observed for solder joints aged at room temperature, where SAC alloys always creep at lower rates than Sn-Pb solder.

Effects of Shear Cycling on the Mechanical Properties of SAC and SAC+X Lead Free Solder Joints

2019 ◽  
Author(s):  
Mohd Aminul Hoque ◽  
Md Mahmudur Chowdhury ◽  
Sa’d Hamasha ◽  
Jeffrey C. Suhling ◽  
Pradeep Lall
Keyword(s):  
Mechanical Properties ◽  
Solder Joints ◽  
Coefficient Of Thermal Expansion ◽  
Real Life ◽  
Material Behavior ◽  
Lead Free ◽  
Lead Free Solder ◽  
Cyclic Shear ◽  
Mechanical Cycling ◽  
Free Solder

Abstract Solder joint reliability is a chief concern in electronic assemblies. Electronic packages consist of various materials, each having their own Coefficient of Thermal Expansion (CTE). When assembled packages experience high temperature gradients and thermal cycles, a mismatch in the CTE values brings about cyclic shear strains in the solder joints, which can ultimately lead to failure. Thus, it is important to understand the effects of shear cycling on the damage accumulated in solder joints. Previous studies conducted on the effect of mechanical cycling on the material behavior of lead free solders have been performed on bulk samples subjected to tension and compression. Our goal in this study was to determine the evolution of the mechanical properties of doped lead free solder joints when subjected to mechanical shear cycling. Experiments conducted on actual solder joints would help us gain a better understanding on the real life effects of shear cycling. The test specimens consisted of a 3 × 3 array of nine solder joints of approximately 0.75 mm diameter. With the aid of specially designed test fixtures, the specimens were gripped and then subjected to mechanical cycling in the shear using an Instron Micromechanical tester. Testing was performed on both SAC305 and SACX (SAC+Bi) solder joints. The joints were cycled for certain durations, and a nanoindentation system was used to measure the evolution of the mechanical properties (elastic modulus, hardness, creep rate) as a function of the number of shear cycles.

Sign in / Sign up

Export Citation Format

Share Document