Corrosion Resistance of Ultrafine-Grained Pure Cu

2014 ◽  
Vol 912-914 ◽  
pp. 69-72
Author(s):  
D.R. Fang ◽  
L.W. Quan ◽  
J. Yang
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Coarse Grained ◽  
Nacl Solution ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Pure Cu

Pure Cu samples were subjected to equal channel angular pressing (ECAP), and the corrosion resistance of the samples was investigated by potentiodynamic polarization measurements and electrochemical impedance spectroscopy measurements in 3.5% NaCl solution. The results show that the corrosion rate of the ultrafine-grained Cu decreases, in comparison with the coarse-grained Cu.

Effect of Equal Channel Angular Pressing and Annealing on Corrosion Resistance of Al-Cu Alloy

2013 ◽  
Vol 803 ◽  
pp. 226-229
Author(s):  
Da Ran Fang ◽  
Chun Liu ◽  
Feng Fang Liu
Keyword(s):  
Corrosion Resistance ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Annealing Treatment ◽  
Coarse Grained ◽  
Nacl Solution ◽  
Angular Pressing ◽  
Cu Alloy ◽  
Low Temperature Annealing ◽  
Ultrafine Grained

Al-3.9wt.%Cu alloy was subjected to equal channel angular pressing (ECAP) and subsequent low temperature annealing treatment, and the corrosion resistance of the samples was investigated by potentiodynamic polarization measurements in 3.5% NaCl solution. The results show that the corrosion rate of the ultrafine-grained alloy increases, in comparison with the coarse-grained alloy. Meanwhile, it is noted that the corrosion resistance of the alloy subjected to ECAP can be improved by relief annealing.

scholarly journals Study on Corrosion Behavior of Ultrafine-Grained Ti-6Al-7Nb Fabricated by Equal Channel Angular Pressing

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 950 ◽  
Author(s):  
Zequn Yu ◽  
Yuecheng Dong ◽  
Xin Li ◽  
Jingzhe Niu ◽  
Igor Alexandrov ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Oxide Film ◽  
Equal Channel Angular Pressing ◽  
Corrosion Behavior ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Electrochemical Measurement ◽  
Coarse Grained ◽  
Angular Pressing ◽  
Ultrafine Grained

The aim of this study was to investigate the corrosion resistance of ultrafine-grained (UFG) Ti-6Al-7Nb fabricated by equal channel angular pressing (ECAP) and coarse-grained (CG) Ti- 6Al- 7Nb. The microstructure of each specimen was investigated by the electron backscattered diffraction (EBSD) method. The corrosion behavior of each specimen was determined by electrochemical measurement in Ringer’s solution. The surface corroded morphologies and oxide film formed on Ti-6Al-7Nb alloy after electrochemical measurement were investigated by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). EBSD investigation shows that the grain size of UFG Ti-6Al-7Nb decreased to ~0.4 µm, accompanied by low angle grain boundaries (LAGBs) accounting for 39%. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) results indicated that UFG Ti-6Al-7Nb alloy possessed a better corrosion resistance. The surface corroded morphologies revealed many small and shallow corrosion pits, which can be attributed to the good compactness of the oxide film and a rapid self- repairing ability of the UFG Ti-6Al-7Nb alloy.

Effect of KI on the Corrosion Resistance of Ni-P Electroless Plating Coating

2014 ◽  
Vol 633-634 ◽  
pp. 817-820
Author(s):  
Ping Liang ◽  
Yun Xia Zhang ◽  
Yan Hua Shi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Phosphorus Content ◽  
Electrochemical Impedance ◽  
Nacl Solution ◽  
Electroless Coating ◽  
Scanning Electron

To improve the corrosion resistance of Ni-P electroless coating, the KI was added in the electroless solution. The surface micrograph was observed using scanning electron microscopy (SEM), and the corrosion resistance of Ni-P coatings in 3.5%NaCl solution was examined by polarization curves and electrochemical impedance spectroscopy (EIS). The experimental results showed that KI reduced the amount of defects and the size of crystal grain of Ni-P coating, and the surface of Ni-P coating became more homogenous, smoother and compact by KI. In addition, the phosphorus content of Ni-P coating was increased by KI. These factors increased the ability to corrosion protection of Ni-P coating.

Corrosion Behavior of Hot-Dip Galvanized Reinforcing Steel Using Electrochemical Impedance Spectroscopy

2011 ◽  
Vol 250-253 ◽  
pp. 222-227 ◽  
Author(s):  
Bi Lan Lin ◽  
Yu Ye Xu
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Chloride Ions ◽  
Reinforcing Steel ◽  
Effective Measure ◽  
Passivation Film ◽  
Corrosion Behaviors

Galvanizing on the surface of reinforcing steel is an effective measure to control corrosion of reinforcing concrete structures. The corrosion behaviors of hot-dip galvanized (HDG) reinforcing steel in simulated concrete pore solution (SCP solution) with various pH and chlodride values were investigated using electrochemical impedance spectroscopy (EIS). Two equivalent circuit models corresponding to the corrosion process were proposed and the evolution feature of the corrosion parameters were analyzed. The results show that when the SCP solution was carbonated seriously (pH<11), there is hydrogen evolution phenomenon and the corrosion resistance of HDG reinforcing steel is decreased. A minute carbonation of SCP solution (11.5≤pH<12.5) favors the further passivation of the zinc layer and the corrosion resistance is enhanced. The corrosion rate of HDG reinforcing steel at pH=12.0 is minimal, around 0.59 μm/year, whereas that at pH=12.5 is approximate 1.21 μm/year. In the conditions of pH=12.5 and NaCl concentration no more than 0.5wt.%, the corrosion resistance of the passivation film on HDG reinforcing steel is good. In a serious carbonation case, the corrosion rate is increased greatly with chloride ions.

Preparation and Characterization of Polylactic Acid Coating on the Surface of Magnesium Alloy

2015 ◽  
Vol 814 ◽  
pp. 132-136 ◽  
Author(s):  
Xian Yang Hua ◽  
Mei Feng He ◽  
Xiao Qin Zhou
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Magnesium Alloy ◽  
Impedance Spectroscopy ◽  
Corrosion Rate ◽  
Polylactic Acid ◽  
Magnesium Alloys ◽  
Electrochemical Impedance ◽  
Hank’S Solution ◽  
Acid Coating

Magnesium is one of the elements necessary for the body, is the man behind the body’s content of potassium ions within the cell are involved in a series of metabolic processes in vivo, including the formation of bone cells , acceleration of bone healing ability. Resulting from the good mechanical properties and biocompatibility, magnesium alloy is used in medical intervention material, but the high corrosion rate of magnesium alloys is the main drawback to their widespread use, especially in biomedical applications. There is a need for developing new coatings that provide simultaneously corrosion resistance and enhanced biocompatibility. In this work the medical magnesium alloy surface are dipped and coated with polylactic acid, so that obtain a dense uniform polylactic acid coating. And the corrosion resistance of the coating is studied in order to obtain controlled degradable and corrosion resisted magnesium alloy biological material. This paper mainly studies the influence of different concentrations of polylactic acid coating on AZ91D magnesium alloy corrosion resistance. The coated samples were immersed in Hank’s solution and the coating performance was studied by electrochemical impedance spectroscopy and scanning electron microscopy. This research is about the influence of the coating on the corrosion resistance of magnesium alloy through the open circuit potential, polarization curves, electrochemical impedance spectroscopy and Mott-Schottky. The results confirmed that the polylactic acid slow down the corrosion rate of AZ91D magnesium alloys in Hank’s solution. And along with the increase of poly lactic acid concentration, the corrosion resistance of magnesium alloys is improved. There is a wide variation of the corrosion morphology magnesium alloy AZ91D specimens after the surface modification using polylactic acid coating, compared with the unmodified.

Effect of Equal Channel Angular Pressing and Annealing on Corrosion Resistance of Cu-Zn Alloy

2013 ◽  
Vol 706-708 ◽  
pp. 78-81 ◽  
Author(s):  
D.R. Fang ◽  
F.F. Liu ◽  
Chun Liu
Keyword(s):  
Corrosion Resistance ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Annealing Treatment ◽  
Coarse Grained ◽  
Nacl Solution ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Ultrafine Grained ◽  
Zn Alloy

Cu-32wt.%Zn alloy was subjected to equal channel angular pressing (ECAP) and subsequent low temperature annealing treatment, and the corrosion resistance of the samples was investigated by potentiodynamic polarization measurements in 3.5% NaCl solution. The results show that the corrosion rate of the ultrafine-grained alloy decreases, in comparison with the coarse-grained alloy. Meanwhile, it is noted that the corrosion resistance of the sample subjected to ECAP can be further improved by relief annealing.

Effect of Equal Channel Angular Pressing on Corrosion Resistance of Al-Mg Alloy

2013 ◽  
Vol 457-458 ◽  
pp. 3-6
Author(s):  
Da Ran Fang ◽  
Fang Li ◽  
Feng Fang Liu ◽  
Jia Jun Li ◽  
Nai Qin Zhao
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Equal Channel Angular Pressing ◽  
Electrochemical Impedance ◽  
Mg Alloy ◽  
Angular Pressing ◽  
Number Of Passes

Al-2.8wt.%Mg alloy samples were subjected to equal channel angular pressing (ECAP) with different number of passes, and the corrosion resistance of as-cast and ECAP-processed samples was investigated by immersion tests and electrochemical impedance spectroscopy measurements. The results show that the corrosion resistance of the alloy is improved with increasing ECAP passes.

Electrochemical Behavior of Corrosion Resistance Alloys

2011 ◽  
Vol 418-420 ◽  
pp. 1097-1101 ◽  
Author(s):  
Tao Zhang ◽  
Hong Yang Jing ◽  
Yong Dian Han ◽  
Lian Yong Xu
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Ambient Temperature ◽  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Inconel 625 ◽  
Nacl Solution ◽  
Nyquist Plots ◽  
Potentiodynamic Polarisation

The electrochemical behavior of corrosion resistance alloys (316L SS, 2205 DSS and Inconel 625) was carried out at ambient temperature in 3.5% NaCl solution using potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS) techniques. Some significant characterization parameters such as Ecorr, Eb, Icorrand △E in polarisation curves were analyzed and compared to reveal the corrosion resistance of corrosion resistance alloys. The ZsimpWin software was utilized to discuss the Nyquist plots of various corrosion resistance alloys. The result shows that the corrosion resistance of the corrosion resistance alloys in 3.5% NaCl solution at ambient temperature follows the sequence: Inconel 625> 2205 DSS > 316L SS.

Electrochemical Impedance Spectroscopy (EIS) Study of Nano-Composite Polyurea Coating under the Wet-Dry Cyclic Conditions

2014 ◽  
Vol 789 ◽  
pp. 495-500
Author(s):  
Bing Ying Wang ◽  
Qing Hao Shi ◽  
Wen Long Zhang
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Composite Coating ◽  
Electrochemical Impedance ◽  
Protective Action ◽  
Experimental Result ◽  
Resistance Property ◽  
Corrosion Resistance Property ◽  
Mass Fractions

The polyurea was modified by adding different amounts of nanometer ZnO. The corrosion behavior of polyurea/primer composite coating system in wet-dry cyclic environment of 3.5% NaCl solution was studied by using the Electrochemical Impedance Spectroscopy (EIS) measurement and adhesion test technology. The experimental result showed that, different mass fractions of nanometer ZnO had different influences on the corrosion resistance property of coating. When the mass fraction of nanometer ZnO was 5%, the composite coating had the largest protective action. The corrosion resistance property of nanometer ZnO can be improved by increasing the density of polyurea coating, however, the corrosion resistance property of polyurea coating will be weakened in case of exceeding the critical adding amount.

Sign in / Sign up

Export Citation Format

Share Document