Experimental Study of Hydraulic Flip Phenomenon inside Diesel Nozzles Using Diesel and Biodiesel

2014 ◽  
Vol 945-949 ◽  
pp. 940-943 ◽  
Author(s):  
Zhuang Shao ◽  
Zhi Xia He ◽  
Zhi Wei Zhou ◽  
Xi Cheng Tao
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Great Influence ◽  
Flow Characteristics ◽  
Injection Pressure ◽  
Cavitating Flow ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
The Difference ◽  
Biodiesel Fuels

As cavitation inside diesel nozzles can improve the spray characteristics, it has long been a hot issue. And together with the increasing attention of biodiesel, it is essential to identify the difference of cavitating flow characteristics between diesel and biodiesel. What’s more, the hydraulic flip phenomenon and cavitating flow with decreasing injection pressure hasn’t been studied. Based on this, cavitating flow inside transparent nozzles of diesel and biodiesel fuels with increasing and decreasing injection pressure was investigated in this paper. Experimental results showed that are quite different from the disappearance of it and it is harder to disappear. Biodiesel and longer nozzle orifices were hard for the hydraulic flip phenomenon to occur, and the disappearance of hydraulic flip phenomenon has great influence on the spray cone angle and the discharge coefficient.

Experimental Study of Cavitating Flow inside Enlarged Transparent Injector Nozzles and its Effect on Spray

2014 ◽  
Vol 945-949 ◽  
pp. 935-939
Author(s):  
Yu Hang Chen ◽  
Zhi Xia He ◽  
Xiao Bin Chen ◽  
Ding Jiang
Keyword(s):  
Single Phase ◽  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Experimental System ◽  
Flow Region ◽  
Cavitating Flow ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Biodiesel Fuels

The complicated cavitating flow inside diesel nozzles has long been concentrated on. Based on the visualization experimental system, cavitating flow characteristic inside transparent nozzles with different length-diameter ratios was investigated in this paper. Experimental results showed that the cavitation is easier to occur for diesel than for biodiesel, and the longer the length of the orifice is, the harder the cavitation and hydraulic flip phenomenon to occur. Discharge coefficient of diesel was higher than that of biodiesel in single-phase flow region, while got much smaller than that of biodiesel in the cavitating flow and hydraulic flip regions.The spray cone angle of diesel was larger than biodiesel in cavitating flow regime, and got much smaller with the increasing of the length-diameter ratios under the same level of injection pressure in diesel and biodiesel fuels.

scholarly journals Experimental Study of Spray Characteristics of Kerosene-Ethanol Blends from a Pressure-Swirl Nozzle

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Tao Zhang ◽  
Bo Dong ◽  
Xun Zhou ◽  
Linan Guan ◽  
Weizhong Li ◽  
...  
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Breakup Length ◽  
Ethanol Blends ◽  
Pressure Swirl ◽  
Spray Velocity

Partial replacement of kerosene by ethanol in a gas turbine is regarded as a good way to improve the spray quality and reduce the fossil energy consumption. The present work is aimed at studying the spray characteristics of kerosene-ethanol blends discharging from a pressure-swirl nozzle. The spray cone angle, discharge coefficient, breakup length, and velocity distribution are obtained by particle image velocimetry, while droplet size is acquired by particle/droplet imaging analysis. Kerosene, E10 (10% ethanol, 90% kerosene), E20 (20% ethanol, 80% kerosene), and E30 (30% ethanol, 70% kerosene) have been considered under the injection pressure of 0.1–1 MPa. The results show that as injection pressure is increased, the discharge coefficient and breakup length decrease, while the spray cone angle, drop size, and spray velocity increase. Meanwhile, the drop size decreases and the spray velocity increases with ethanol concentration when the injection pressure is lower than 0.8 MPa. However, the spray characteristics are not affected obviously by the ethanol concentration when the injection pressure exceeds 0.8 MPa. A relation to breakup length for kerosene-ethanol blends is obtained. The findings demonstrate that the adding of ethanol into kerosene can promote atomization performance.

Characteristics of Hollow Cone Swirl Spray at Various Nozzle Orifice Diameters

2012 ◽  
Vol 58 (2) ◽  
Author(s):  
A. Hussein ◽  
M. Hafiz ◽  
H. Rashid ◽  
A. Halim ◽  
W. Wisnoe ◽  
...  
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Orifice Diameter ◽  
Hollow Cone ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Nozzle Orifice ◽  
Breakup Length

An experimental work to investigate the swirl spray characteristics that emanates from hollow–cone and solid–cone spray simplex atomizers is presented. Main objective of the research is to investigate the spray characteristics, i.e. spray breakup length, discharge coefficient and spray cone angle at different nozzle orifice diameter and injection pressure. Discharge coefficient is almost uninfluenced by the operating Reynolds number. This test also reveals that both breakup length and spray cone angle increases as orifice diameter is increased. Higher injection pressure leads to shorter breakup length and wider spray cone angle.

Effect of geometric and operating parameters on the spray characteristics of an open-end swirl injector

2019 ◽  
Vol 233 (12) ◽  
pp. 4457-4467 ◽  
Author(s):  
Chen Chen ◽  
Yang Yang ◽  
Xiaorong Wang ◽  
Wenxian Tang
Keyword(s):  
Pressure Drop ◽  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Operating Parameters ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Breakup Length ◽  
Swirl Chamber ◽  
Swirl Injector

To study the influence of geometric and operating parameters on the spray characteristics of an open-end swirl injector, seven injectors with different tangential inlet diameters ( D p) and injector length to injector orifice diameter ( L/D) ratios were tested and simulated. Using high-speed backlight, the evolution laws of liquid film thickness, discharge coefficient, spray cone angle, breakup length, and velocity distribution in the swirl chamber under different geometric and operating parameters were captured after unified image processing. Low-injection pressure drop is directly proportional to the discharge coefficient and the spray cone angle. When the injection pressure drop approaches or reaches a critical value of 0.4 MPa, the discharge coefficient and spray cone angle remain nearly constant with maximum fluctuations of 1% and 5%, respectively. With an increase in the geometric characteristic constant A, the liquid film thickness, discharge coefficient, breakup length, and velocity in the swirl chamber decrease, whereas the spray cone angle increases. As the viscous effect increases for increasing L/D, the discharge coefficient and breakup length increase, whereas the spray cone angle decreases. Based on experiment results, empirical formulas for the discharge coefficient, spray angle, and breakup length were put forward as reference for engineering applications, including the effect of the geometric and operating parameters.

scholarly journals Calculation of flow characteristics of liquid fuel supplied through pressure jet atomizers of small-sized gas turbine engines

2021 ◽  
Vol 20 (2) ◽  
pp. 19-35
Author(s):  
N. I. Gurakov ◽  
I. A. Zubrilin ◽  
M. Hernandez Morales ◽  
D. V. Yakushkin ◽  
A. A. Didenko ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Liquid Fuel ◽  
Cone Angle ◽  
Flow Characteristics ◽  
Design Parameters ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Semi Empirical

The paper presents the results of studying the flow characteristics of liquid fuel in pressure jet atomizers of small-sized gas turbine engines with nozzle diameters of 0.4-0.6 mm for various operating and design parameters. The study was carried out using experimental measurements, semi-empirical correlations and CFD (computational fluid dynamics) methods. The Euler approach, the volume- of- fluid (VOF) method, was used to model multiphase flows in CFD simulations. Good agreement was obtained between experimental and predicted data on the fuel coefficient and the primary spray cone angle at the nozzle outlet. Besides, the assessment of the applicability of semi-empirical techniques for the nozzle configurations under consideration is given. In the future, the flow characteristics in question (the nozzle flow rate, the fuel film thickness, and the primary spray cone angle) can be used to determine the mean diameter of the droplets (SMD) required to fully determine the boundary conditions of fuel injection when modeling combustion processes in combustion chambers of small-sized gas turbine engines.

Characterizing Diesel Fuel Spray Cone Angle From Back-Scattered Imaging by Fitting Gaussian Profiles to Radial Spray Intensity Distributions

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Jaclyn E. Johnson ◽  
Jeffrey D. Naber ◽  
Seong-Young Lee
Keyword(s):  
Charge Density ◽  
Diesel Fuel ◽  
Curve Fitting ◽  
Cone Angle ◽  
Injection Pressure ◽  
Fuel Spray ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Gaussian Curve

Quantifying fuel spray properties including penetration, cone angle, and vaporization processes sheds light on fuel-air mixing phenomenon, which governs subsequent combustion and emissions formation in diesel engines. Accurate experimental determination of these spray properties is a challenge but imperative to validate computational fluid dynamic (CFD) models for combustion prediction. This study proposes a new threshold independent method for determination of spray cone angle when using Mie back-scattering optical diagnostics to visualize diesel sprays in an optically accessible constant volume vessel. Test conditions include the influence of charge density (17.6 and 34.9 kg/m3) at 1990 bar injection pressure, and the influence of injection pressure (990, 1370, and 1980 bar) at a charge density of 34.8 kg/m3 on diesel fuel spray formation from a multi-hole injector into nitrogen at a temperature of 100 °C. Conventional thresholding to convert an image to black and white for processing and determination of cone angle is threshold subjective. As an alternative, an image processing method was developed, which fits a Gaussian curve to the intensity distribution of the spray at radial spray cross-sections and uses the resulting parameters to define the spray edge and hence cone angle. This Gaussian curve fitting methodology is shown to provide a robust method for cone angle determination, accounting for reductions in intensity at the radial spray edge. Results are presented for non-vaporizing sprays using this Gaussian curve fitting method and compared to the conventional thresholding based method.

Effect of Injection Parameters on the Spray Characteristics of DME Fuel

2006 ◽  
Author(s):  
Bong Woo Ryu ◽  
Seung Hwan Bang ◽  
Hyun Kyu Suh ◽  
Chang Sik Lee
Keyword(s):  
Dimethyl Ether ◽  
Diesel Fuel ◽  
Cone Angle ◽  
Injection Pressure ◽  
Injection Rate ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Injection Duration ◽  
Injection Parameters

The purpose of this study is to investigate the effect of injection parameters on the injection and spray characteristics of dimethyl ether and diesel fuel. In order to analyze the injection and spray characteristics of dimethyl ether and diesel fuel with employing high-pressure common-rail injection system, the injection characteristics such as injection delay, injection duration, and injection rate, spray cone angle and spray tip penetration was investigated by using the injection rate measuring system and the spray visualization system. In this work, the experiments of injection rate and spray visualization are performed at various injection parameters. It was found that injection quantity was decreased with the increase of injection pressure at the same energizing duration and injection pressure In the case of injection characteristics, dimethyl ether showed shorter of injection delay, longer injection duration and lower injected mass flow rate than diesel fuel in accordance with various energizing durations and injection pressures. Also, spray development of dimethyl ether had larger spray cone angle than that of diesel fuel at various injection pressures. Spray tip penetration was almost same development and tendency regardless of injection angles.

Experimental Study on Diesel Engine and Analysis the Spray Characteristics of Diesel and Biodiesel by Varying Injection Pressure

2014 ◽  
Vol 984-985 ◽  
pp. 932-937 ◽  
Author(s):  
Palani Raghu ◽  
M. Senthamil Selvan ◽  
K. Pitchandi ◽  
N. Nallusamy
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Weber Number ◽  
Direct Injection ◽  
Cone Angle ◽  
Injection Pressure ◽  
Injection Velocity ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone

— The spray characteristic of the injected fuel is mainly depends upon fuel injection pressure, temperature, ambient pressure, fuel viscosity and fuel density. An experimental study was conducted to examine the effect of injection pressure on the spray was injected into direct injection (DI) diesel engine in the atmospheric condition. In Diesel engine, the window of 20 mm diameter hole and the transparent quartz glass materials were used for visualizing spray characteristics of combustion chamber at right angle triangle position. The varying Injection pressure of 180 - 240 bar and the engine was hand cranked for conducting the experiments. Spray characteristics for Jatropha oil methyl ester (JOME) and diesel were studied experimentally. Spray tip penetration and spray cone angle were measured in a combustion chamber of Direct Injection diesel engine by employing high speed Digital camera using Mie Scattering Technique and ImageJ software. The study shows the JOME gives longer spray tip penetration and smaller spray cone angle than those of diesel fuels. The Spray breakup region (Reynolds number, Weber number), Injection velocity and Sauter Mean Diameter (SMD) were determined for diesel and JOME. SMD decreases for JOME than diesel and the Injection velocity, Reynolds Number, Weber Number Increases for JOME than diesel.

Sign in / Sign up

Export Citation Format

Share Document