Heat and Mass Transfer in 3D Non-Newtonian Nano and Ferro Fluids over a Bidirectional Stretching Surface

2015 ◽  
Vol 21 ◽  
pp. 33-51 ◽  
Author(s):  
Chakravarthula S.K. Raju ◽  
Naramgari Sandeep
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Friction Factor ◽  
Heat Transfer Performance ◽  
Three Dimensional ◽  
Transfer Performance ◽  
Stretching Surface ◽  
Three Dimensional Flow ◽  
Source Sink ◽  
Bidirectional Stretching

An analysis has been carried out for three-dimensional flow of magneto hydrodynamic Sisko ferro and nanofluids over a bidirectional stretching surface in porous medium with non-uniform heat source/sink. The set of nonlinear governing partial differential equations are transformed in to ordinary differential equations by using self-suitable transformations, and solved numerically using Runge-Kutta and Newton’s methods. The acquired results presents the effects of various non-dimensional governing parameters on velocity and temperature profiles. Also, determined and analyzed the friction factor coefficients and local Nusselt number. We have presented dual solutions for Sisko ferro and nanofluid cases. An excellent agreement of the present results has been found with existed literature under some special limited cases. Results depict that the material parameter have tendency to boost the friction factor coefficients along with the heat transfer rate. It is also observed that the heat transfer performance of Sisko nanofluid is high while compared with the heat transfer performance of the Sisko ferro fluid.

scholarly journals Computational Study of Flow and Heat Transfer With Anti Cross-Flows (ACF) Jet Impingement Cooling for Different Heights of Corrugate

2017 ◽  
Author(s):  
Radheesh Dhanasegaran ◽  
Ssheshan Pugazhendhi
Keyword(s):  
Heat Transfer ◽  
Skin Friction ◽  
Heat Transfer Performance ◽  
Computational Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Transfer Performance ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Plate Spacing

In the present study, a flow visualization and heat transfer investigation is carried out computationally on a flat plate with 10×1 array of impinging jets from a corrugated plate. This corrugated structure is an Anti-Cross Flow (ACF) technique which is proved to nullify the negative effects of cross-flow thus enhancing the overall cooling performance. Governing equations are solved using k-ω Shear Stress Transport (SST) turbulence model in commercial code FLUENT. The parameter variation considered for the present study are (i) three different heights of ACF corrugate (C/D = 1, 2 & 3) and (ii) two different jet-to-target plate spacing (H/D = 1 & 2). The dependence of ACF structure performance on the corrugate height (C/D) and the flow structure has been discussed in detail, therefore choosing an optimum corrugate height and visualizing the three-dimensional flow phenomena are the main objectives of the present study. The three-dimensional flow separation and heat transfer characteristics are explained with the help of skin friction lines, upwash fountains, wall eddies, counter-rotating vortex pair (CRVP), and plots of Nusselt number. It is found that the heat transfer performance is high at larger corrugate heights for both the jet-to-plate spacing. Moreover, the deterioration of the skin friction pattern corresponding to the far downstream impingement zones is greatly reduced with ACF structure, retaining more uniform heat transfer pattern even at low H/D values where the crossflow effects are more dominant in case of the conventional cooling structure. In comparison of the overall heat transfer performance the difference between C/D = 3 & C/D = 2 for H/D = 2 is significantly less, thus making the later as the optimal configuration in terms of reduced channel height.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

Experimental and Numerical Studies of Fluid Flow Confined in Microchannel

2016 ◽  
Author(s):  
Yan Wang ◽  
Xiang Ling
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Friction Factor ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Parallel Microchannels

The heat transfer performance of fluid flowing in a microchannel was experimentally studied, to meet the requirement of extremely high heat flux removal of microelectronic devices. There were 10 parallel microchannels with rectangular cross-section in the stainless steel plate, which was covered by a glass plate to observe the fluid flowing behavior, and another heating plate made of aluminum alloy was positioned behind the microchannel. Single phase heat transfer and fluid flow downstream the microchannel experiments were conducted with both deionized water and ethanol. Besides experiments, numerical models were also set up to make a comparison with experimental results. It is found that the pressure drop increases rapidly with enlarging Reynolds number (200), especially for ethanol. With comparison, the flow resistance of pure water is smaller than ethanol. Results also show that the friction factor decreases with Reynolds number smaller than the critical value, while increases the velocity, the friction factor would like to keep little changed. We also find that the water friction factors obtained by CFD simulations in parallel microchannels are much larger than experiment results. With heat flux added to the fluid, the heat transfer performance can be enhanced with larger Re number and the temperature rise could be weaken. Compared against ethanol, water performed much better for heat removal. However, with intensive heat flux, both water and ethanol couldn’t meet the requirement and the temperature at outlet would increase remarkably, extremely for ethanol. These findings would be helpful for thermal management design and optimization.

Heat Transfer Enhancement for Wake Zone Using Slit Pillar in Microchannel Heat Sinks

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Xiao Cheng ◽  
Huiying Wu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Electronic Device ◽  
Three Dimensional ◽  
Lower Surface ◽  
Heat Sinks ◽  
Transfer Performance ◽  
Microchannel Heat Sinks ◽  
Dimensional Simulation ◽  
Wake Zone

Abstract Pillar microchannel heat sinks have been widely used for chip cooling, while their overall heat transfer performance is restricted by the stagnation flow in pillar wake zone. In this work, a simple but effective method using slit microstructure modified on pillar was proposed to enhance wake zone heat transfer. It enables a special flow path for the incoming fluid that intensively disturbs the wake fluid. To validate the proposed method, a three-dimensional simulation was employed to study the laminar flow and heat transfer characteristics in the slit pillar microchannel. The pillar without slit design was also investigated for comparative analysis. Effects of slit angle (θ), height over diameter ratio (H/D), and blocking ratio (D/W) of a single pillar were systematically studied at the Reynolds numbers of 26–260. Results showed the case with θ = 0 deg always demonstrated lower surface temperature, higher Nusselt number and higher thermal performance index (TPI) compared to other cases with different slit angles at the same conditions. Furthermore, it was interesting to find that the slit configuration was not suitable for long pillar microchannel, but preferred for high blocking ratio pillar microchannel at present ranges (H/D ≤ 1, D/W ≤ 0.5). The slit pillar array microchannel was also explored and observed with improved overall heat transfer performance. The proposed slit microstructure well prevents the heat transfer deterioration in pillar wake zone, which is promisingly to be used for cooling performance improvement of electronic device.

Enhanced Condensation Heat-Transfer on Mini or Low Fin Tubes

2006 ◽  
Author(s):  
Adrian Briggs
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Thermophysical Properties ◽  
Heat Transfer Performance ◽  
Three Dimensional ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Shell Side ◽  
Wide Range ◽  
Fin Tubes

This paper presents an overview of the use of low or mini-fin tubes for improving heat-transfer performance in shell-side condensers. The paper concentrates on, but is not limited to, the experimental and theoretical program in progress at Queen Mary, University of London. This work has so far resulted in an extensive data base of experimental data for condensation on single tubes, covering a wide range of tube geometries and fluid thermophysical properties and in the development of a simple to use model which predicts the majority of this data to within 20%. Work is progressing on the effects of vapor shear and on three-dimensional fin profiles; the later having shown the potential for even higher heat-transfer enhancement.

Numerical Investigation of a Crossflow Jet in a Rectangular Microchannel

2013 ◽  
Vol 284-287 ◽  
pp. 849-853
Author(s):  
Kok Cheong Wong
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Three Dimensional ◽  
Horizontal Flow ◽  
Transfer Performance ◽  
Rectangular Microchannel ◽  
Transverse Jet ◽  
Nozzle Position ◽  
Jet Nozzle

The present numerical study is conducted in three dimensional to investigate the crossflow of an external round jet and a horizontal stream of microchannel flow. The results of heat transfer performance for the cases with and without transverse jet are compared. The patterns of different crossflow jet were analyzed to understand the flow and heat transfer characteristics. The effect of jet nozzle position on the heat transfer is investigated. Generally, the heat transfer performance increases with the jet Reynolds number. However, some cases of weak jet are found to cause lower heat transfer rate relative to the case without external jet. When vertical weak jet encounter strong horizontal flow, the horizontal flow is dominant that the jet cannot reach the microchannel bottom wall but imposes resistance to the horizontal flow. The investigation on the jet nozzle location shows that the jet nozzle location closer to the channel inlet gives better heat transfer performance.

Mixed convection squeezing three-dimensional flow in a rotating channel filled with nanofluid

2016 ◽  
Vol 26 (5) ◽  
pp. 1460-1485 ◽  
Author(s):  
B Mahanthesh ◽  
B J Gireesha ◽  
R S R Gorla
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Differential Equations ◽  
Mixed Convection ◽  
Three Dimensional ◽  
Vertical Channel ◽  
Three Dimensional Flow ◽  
Content Type ◽  
Dimensional Flow ◽  
Rotating Channel

Purpose – The purpose of this paper is to numerically solve the problem of an unsteady squeezing three-dimensional flow and heat transfer of a nanofluid in rotating vertical channel of stretching left plane. The fluid is assumed to be Newtonian, incompressible and electrically conducting embedded with nanoparticles. Effect of internal heat generation/ absorption is also considered in energy equation. Four different types of nanoparticles are considered, namely, copper (Cu), alumina (Al2O3), silver (Ag) and titanium oxide (TiO2) with the base fluid as water. Maxwell-Garnetts and Brinkman models are, respectively, employed to calculate the effective thermal conductivity and viscosity of the nanofluid. Design/methodology/approach – Using suitable similarity transformations, the governing partial differential equations are transformed into set of ordinary differential equations. Resultant equations have been solved numerically using Runge-Kutta-Fehlberg fourth fifth order method for different values of the governing parameters. Effects of pertinent parameters on normal, axial and tangential components of velocity and temperature distributions are presented through graphs and discussed in detail. Further, effects of nanoparticle volume fraction, squeezing parameter, suction/injection parameter and heat source/sink parameter on skin friction and local Nusselt number profiles for different nanoparticles are presented in tables and analyzed. Findings – Squeezing effect enhances the temperature field and consequently reduces the heat transfer rate. Large values of mixed convection parameter showed a significant effect on velocity components. Also, in many heat transfer applications, nanofluids are potentially useful because of their novel properties. They exhibit high-thermal conductivity compared to the base fluids. Further, squeezing and rotation effects are desirable in control the heat transfer. Originality/value – Three-dimensional mixed convection flows over in rotating vertical channel filled with nanofluid are very rare in the literature. Mixed convection squeezing three-dimensional flow in a rotating channel filled with nanofluid is first time investigated.

Sign in / Sign up

Export Citation Format

Share Document