Tribological Performance of Two Oilless Sintered-Metal Bearings for the Geared Motor in a Refrigerator

2006 ◽  
Vol 321-323 ◽  
pp. 1552-1555
Author(s):  
Se Doo Oh ◽  
Young Ze Lee
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tribological Performance ◽  
The Other ◽  
Tribological Characteristics ◽  
Sintered Metal ◽  
Before And After ◽  
Frictional Forces ◽  
Scanning Electron

The tribological performances of two types of oilless sintered-metal bearings with varying loads were investigated. One is the Cu-based bearing and the other is Fe-based bearing. The frictional forces of the bearings were measured using the bearing tester. By measuring the change of weight before and after sliding tests, the oil losses of the bearings were surveyed. Also, PV curves, which could be used to predict the life of the oilless bearing, were plotted. By observing the roundness, the cylindericity and the images of scanning electron microscopy of bearings before and after sliding tests, the tribological characteristics of the bearings were evaluated. It was found that Fe-based bearing show lower friction, more oil loss, less wear and longer life than Cu-based bearing.

Experimental Study on Frictional Force and Wear Life of Oilless Sintered-Metal Bearings for the Reliability of the Geared Motor

2006 ◽  
Vol 326-328 ◽  
pp. 585-588
Author(s):  
Se Doo Oh ◽  
Yun Ha Shin ◽  
Young Ze Lee
Keyword(s):  
Electron Microscopy ◽  
Journal Bearing ◽  
The Other ◽  
Metal Powders ◽  
Sintered Metal ◽  
Wear Life ◽  
Before And After ◽  
Oil Flow ◽  
Frictional Forces ◽  
Scanning Electron

Oilless bearings, which are made with metal powders and then impregnated by oils, are widely used in rotating components. The friction coefficients and the oil loss rates of two types of oil-impregnated sintered-metal bearings (porous bearings, oilless bearings, or oilless metals) with varying loads were measured. One is the Cu-based bearing and the other is Fe-based bearing. The frictional forces of the bearings were measured using the journal bearing tester. By measuring the change of weight before and after sliding tests, the oil losses of oilless bearings were surveyed. Also, PV curves, which could be used to predict the life of the oilless bearing, were plotted. By observing the roundness, the cylindericity and the images of scanning electron microscopy of bearings before and after sliding tests, the tribological characteristics of the bearings were evaluated. It was found that Fe-based bearing show lower friction, more oil flow, less wear and longer life than Cu-based bearing.

scholarly journals Redox Mechanism of Azathioprine and Its Interaction with DNA

2021 ◽  
Vol 22 (13) ◽  
pp. 6805
Author(s):  
Mihaela-Cristina Bunea ◽  
Victor-Constantin Diculescu ◽  
Monica Enculescu ◽  
Horia Iovu ◽  
Teodor Adrian Enache
Keyword(s):  
Electron Microscopy ◽  
Mass Spectrometry ◽  
Scanning Electron Microscopy ◽  
Structural Changes ◽  
Differential Pulse ◽  
Immunosuppressive Drug ◽  
Redox Mechanism ◽  
Before And After ◽  
Dna Film ◽  
Scanning Electron

The electrochemical behavior and the interaction of the immunosuppressive drug azathioprine (AZA) with deoxyribonucleic acid (DNA) were investigated using voltammetric techniques, mass spectrometry (MS), and scanning electron microscopy (SEM). The redox mechanism of AZA on glassy carbon (GC) was investigated using cyclic and differential pulse (DP) voltammetry. It was proven that the electroactive center of AZA is the nitro group and its reduction mechanism is a diffusion-controlled process, which occurs in consecutive steps with formation of electroactive products and involves the transfer of electrons and protons. A redox mechanism was proposed and the interaction of AZA with DNA was also investigated. Morphological characterization of the DNA film on the electrode surface before and after interaction with AZA was performed using scanning electron microscopy. An electrochemical DNA biosensor was employed to study the interactions between AZA and DNA with different concentrations, incubation times, and applied potential values. It was shown that the reduction of AZA molecules bound to the DNA layer induces structural changes of the DNA double strands and oxidative damage, which were recognized through the occurrence of the 8-oxo-deoxyguanosine oxidation peak. Mass spectrometry investigation of the DNA film before and after interaction with AZA also demonstrated the formation of AZA adducts with purine bases.

Synthesis and Film Investigation of Titania

2013 ◽  
Vol 832 ◽  
pp. 128-131
Author(s):  
Sharipah Nadzirah ◽  
Uda Hashim
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Thin Films ◽  
Scanning Electron Microscopy ◽  
Titanium Dioxide ◽  
Sol Gel ◽  
Titanium Butoxide ◽  
Before And After ◽  
Scanning Electron ◽  
Spin Coater

Titania or titanium dioxide (TiO2) thin film has been synthesized via sol-gel method with monoethanolamine (MEA) as a catalyst. The mixing of titanium butoxide as a precursor, ethanol as a solvent and MEA were stirred using magnetic stirrer under ambient temperature [. The TiO2solution prepared then was deposited on SiO2substrates using spin-coater and the coated films were annealed at 600°C. Finally, both before and after annealed TiO2thin films were characterized using Field Emission Scanning Electron Microscopy (FESEM). The obtained results show the different TiO2particles formation before and after annealed.

Problems associated with ageing squid from their statoliths: towards a more structured approach

1994 ◽  
Vol 6 (2) ◽  
pp. 215-222 ◽  
Author(s):  
Marek R. Lipinski ◽  
M. Deon Durholtz
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Regression Analysis ◽  
Light Microscopy ◽  
The Other ◽  
Etching Solution ◽  
Significant Difference ◽  
Structured Approach ◽  
Fish Otoliths ◽  
Scanning Electron

It appears that squid statoliths cannot yet be regarded as accurate an ageing tool as fish otoliths. Statoliths from the same pair, prepared differently for viewing and counting increments, were compared. Increment counts do not imply age in days, because this was not validated. One statolith from each pair was examined by light microscopy (LM) after preparation following a new method. The other was viewed by Scanning Electron microscopy (SEM) with a modified etching solution. Shape of each statolith was similar when compared by multiple regression analysis (11 variables, n=53). There was a weak but significant difference between sexes (statoliths of females were slightly larger). All other differences were insignificant. Microscopic observation and increment counts of increments were successfully carried out for 37 pairs of statoliths. Significant differences between two independent counts were found for the LM method, but no significant differences were found between two independent SEM counts. Counts were significantly different when interpreted by both LM and SEM, probably because of poor resolution in the LM readings and over-resolution (growth layers prominent and numerous) in those read by SEM. Recommendations are made on how ageing studies, based on statoliths, should be structured and the results evaluated.

Pollen morphology of Sabinaria magnifica (Cryosophileae, Coryphoideae, Arecaceae)

Phytotaxa ◽  
2015 ◽  
Vol 207 (1) ◽  
pp. 135 ◽  
Author(s):  
Giovanni Raul Bogota ◽  
Carina Hoorn ◽  
Wim Star ◽  
Rob Langelaan ◽  
Hannah Banks ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Light Microscopy ◽  
Pollen Morphology ◽  
Pollen Grains ◽  
The Other ◽  
Transmission Electron ◽  
Palm Species ◽  
Scanning Electron

Sabinaria magnifica is so far the only known species in the recently discovered tropical palm genus Sabinaria (Arecaceae). Here we present a complete description of the pollen morphology of this palm species based on light microscopy (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). We also made SEM-based comparisons of Sabinaria with other genera within the tribe Cryosophileae. Pollen grains of Sabinaria magnifica resemble the other genera in the heteropolar, slightly asymmetric monads, and the monosulcate and tectate exine with perforate surface. Nevertheless, there are some clear differences with Thrinax, Chelyocarpus and Cryosophila in terms of aperture and exine. S. magnifica differs from its closest relative, Itaya amicorum, in the exine structure. This study shows that a combination of microscope techniques is essential for the identification of different genera within the Cryosophileae and may also be a necessary when working with other palynologically less distinct palm genera. 

scholarly journals Effect of Different Cooling Regimes on the Mechanical Properties of Cementitious Composites Subjected to High Temperatures

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Jiangtao Yu ◽  
Wenfang Weng ◽  
Kequan Yu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
High Temperature ◽  
Significant Influence ◽  
Microstructural Characterization ◽  
Cementitious Composite ◽  
Engineered Cementitious Composite ◽  
Before And After ◽  
Scanning Electron

The influence of different cooling regimes (quenching in water and cooling in air) on the residual mechanical properties of engineered cementitious composite (ECC) subjected to high temperature up to 800°C was discussed in this paper. The ECC specimens are exposed to 100, 200, 400, 600, and 800°C with the unheated specimens for reference. Different cooling regimens had a significant influence on the mechanical properties of postfire ECC specimens. The microstructural characterization was examined before and after exposure to fire deterioration by using scanning electron microscopy (SEM). Results from the microtest well explained the mechanical properties variation of postfire specimens.

scholarly journals In VitroAdherence of Oral Bacteria to Different Types of Tongue Piercings

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Lucas Pereira Borges ◽  
Julio Cesar Campos Ferreira-Filho ◽  
Julia Medeiros Martins ◽  
Caroline Vieira Alves ◽  
Bianca Marques Santiago ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Bacterial Adhesion ◽  
Oral Bacteria ◽  
The Other ◽  
Control Group ◽  
Colony Forming Units ◽  
Different Types ◽  
Scanning Electron

The purpose of this work was to verifyin vitroadherence ofE. corrodensandS. oralisto the surface of tongue piercings made of surgical steel, titanium, Bioplast, and Teflon. For this, 160 piercings were used for the count of Colony Forming Units (CFU) and 32 piercings for analysis under scanning electron microscopy. Of these, 96 (24 of each type) were individually incubated in 5 mL of BHI broth and 50 μL of inoculum at 37°C/24 h. The other 96 piercings formed the control group and were individually incubated in 5 mL of BHI broth at 37°C/24 h. Plates were incubated at 37°C/48 h for counting of CFU/mL and data were submitted to statistical analysis (pvalue<0.05). ForE. corrodens, difference among types of material was observed (p<0.001) and titanium and surgical steel showed lower bacterial adherence. The adherence ofS. oralisdiffered among piercings, showing lower colonization (p<0.007) in titanium and surgical steel piercings. The four types of piercings were susceptible to colonization byE. corrodensandS. oralis, and bacterial adhesion was more significant in those made of Bioplast and Teflon. The piercings presented bacterial colonies on their surface, being higher in plastic piercings probably due to their uneven and rough surface.

Fine morphology of the cuticle surface of Chordodes anthophorus and reinterpretation of C. aquaeductus, C. ferganensis and C. oscillatus (Gordiida Nematomorpha)

Zootaxa ◽  
2007 ◽  
Vol 1397 (1) ◽  
pp. 39-45 ◽  
Author(s):  
CRISTINA DE VILLALOBOS ◽  
FERNANDA ZANCA ◽  
SERGEI SPIRIDONOV
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Central Asia ◽  
The Other ◽  
Species Status ◽  
Taxonomic Descriptions ◽  
Former Ussr ◽  
Fine Morphology ◽  
Scanning Electron

We reinvestigate four species of the genus Chordodes from Central Asia and one from Georgia (Transcaucasian part of former USSR) in order to certify the taxonomic descriptions and verify the species status. By scanning electron microscopy, we demonstrate characteristic cuticular patterns for Chordodes anthophorus. The other three species, C. aquaeductus, C. ferganensis and C. oscillatus are synonymized with C. anthophorus because no differences were detected.

scholarly journals Effect of denture surface glazing on denture plaque formation

2005 ◽  
Vol 16 (2) ◽  
pp. 129-134 ◽  
Author(s):  
Newton Sesma ◽  
Dalva Cruz Laganá ◽  
Susana Morimoto ◽  
Carlos Gil
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Bacterial Colonization ◽  
Plaque Formation ◽  
The Other ◽  
Bacterial Plaque ◽  
The Right ◽  
Clinical Experiment ◽  
Scanning Electron

This study evaluated, in vivo, the efficacy of a denture glazing material (Palaseal) in modifying plaque colonization of dentures. Ten subjects were selected and received maxillary temporary partial removable dentures, with complete acrylic palatal coverage. The right half of the fitting surface of the denture bases were glazed with Palaseal, whereas the other half was not glazed. One month after insertion, two fragments of the resin base of all dentures were removed (one from the glazed side and another from the non-glazed side). These samples were prepared and examined by scanning electron microscopy. Three months after insertion, other fragments were obtained and analyzed. Microscopic observation at 1 month revealed that, for all patients, the plaque film was thinner on the treated side in comparison to the non-treated side. However, at the 3-month evaluation, some areas of the glaze showed cracking, and both glazed and non-glazed sides were covered by a dense bacterial plaque film. In conclusion, the findings of this clinical experiment showed that glazing denture's fitting surface did not prevent bacterial colonization, but favored plaque removal while the glaze layer remained intact. After three months, glaze cracks created microretentive areas that increased plaque accumulation.

Silica deposition in the inflorescence bracts of wheat (Triticum aestivum). I. Scanning electron microscopy and light microscopy

1988 ◽  
Vol 66 (5) ◽  
pp. 829-838 ◽  
Author(s):  
M. J. Hodson ◽  
A. G. Sangster
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Triticum Aestivum ◽  
Light Microscopy ◽  
Triticum Aestivum L ◽  
The Other ◽  
Deposition Pattern ◽  
Membranous Structure ◽  
Silica Deposition ◽  
Scanning Electron

Silica deposition in the lower glume, lemma, and palea of wheat (Triticum aestivum L. cv. Highbury) was investigated using scanning electron microscopy and light microscopy. Silica was present in the outer walls of all the epidermal cells including prickles and papillae of the glume and lemma awns. The glume and the lemma were similar in epidermal silica deposition pattern, both having numerous silicified short trichomes and papillae on inner and outer surfaces. Epidermal long cells and short cells were also silicified. Macrohairs were restricted to isolated areas in these bracts, particularly on the inner surfaces just beneath the awns. The palea was a thin membranous structure differing markedly from the other two bracts. Most of the palea is pressed between the caryopsis and the next floret, and both surfaces are almost devoid of trichomes in these areas. However, at the apex and margins of the palea, macrohairs and papillae were abundant. The results are discussed with respect to possible taxonomic, anatomical, medical, and archaeological implications.

Sign in / Sign up

Export Citation Format

Share Document