Effect of Pb Content on the Fatigue Properties of D.C. Reactive Sputtering-Derived PZT Thin Films

2006 ◽  
Vol 326-328 ◽  
pp. 613-616
Author(s):  
Dae Jin Yang ◽  
Seong Je Cho ◽  
Jong Oh Kim ◽  
Won Youl Choi
Keyword(s):  
Lead Zirconate Titanate ◽  
Perovskite Phase ◽  
Fatigue Behavior ◽  
Ferroelectric Properties ◽  
Pyrochlore Phase ◽  
Reactive Sputtering ◽  
Lead Zirconate ◽  
Fatigue Properties ◽  
Pzt Thin Films ◽  
Pzt Films

Lead zirconate titanate (Pb(Zr0.48Ti0.52)O3 or PZT) films were grown on platinized silicon wafers (Pt/SiO2/Si) by d.c. reactive sputtering method with multi targets. The Pb content of PZT films has been widely recognized as affecting not only the phase formation and microstructure but also the dielectric and ferroelectric properties. Pb content of PZT films was controlled by the variation of Pb target current. The relation between Pb content and Pb target current was expressed as y=0.89x-11.09. The x and y are Pb target current and Pb content, respectively. The pyrochlore phase was transformed to perovskite phase as Pb content was increased. This phase transformation improved the ferroelectric properties of PZT films. In PZT films with perovskite phase, fatigue properties were not improved with excess Pb content. Fatigue properties of PZT films began to be fatigued after 106 switching cycles and coincided with the typical PZT fatigue behavior. Excess Pb content (Pb vacancy) did not affect the fatigue properties of PZT films.

Effect of Pb Excess Content on Microstructure and Electrical Properties of Sol Gel Derived PZT Thin Films

1999 ◽  
Vol 596 ◽  
Author(s):  
Zhan-jie Wang ◽  
Ryutaro Maeda ◽  
Kaoru Kikuchi
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Lead Zirconate ◽  
Pzt Thin Films ◽  
Starting Solution ◽  
Pzt Films

AbstractLead zirconate titanate (PZT) thin films were fabricated by a three-step heat-treatment process which involves the addition of -10, 0 and 10 mol% excess Pb to the starting solution and spin coating onto Pt/Ti/SiO2/Si substrates. Crystalline phases as well as preferred orientations in PZT films were investigated by X-ray diffraction analysis (XRD). The microstructure and composition of the films were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA), respectively. The well-crystallized perovskite phase and the (100) preferred orientation were obtained by adding 10% excess Pb to the starting solution. It was found that PZT films to which 10% excess Pb was added had better electric properties. The remanent polarization and the coercive field of this film were 34.8 μC/cm2 and 41.7 kV/cm, while the dielectric constant and loss values measured at 1 kHz were approximately 1600 and 0.04, respectively. Dielectric and ferroelectric properties were correlated to the microstructure of the films.

EFFECT OF PRE-HEATING TEMPERATURE ON THE CHARACTERISTICS OF PZT THIN FILMS GROWN BY USING A TRIOL SOL–GEL ROUTE

2007 ◽  
Vol 14 (02) ◽  
pp. 229-234
Author(s):  
SARAWUT THOUNTOM ◽  
MANOCH NAKSATA ◽  
KENNETH MACKENZIE ◽  
TAWEE TUNKASIRI
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Heating Temperature ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Hysteresis Loops ◽  
Lead Zirconate ◽  
Pzt Thin Films ◽  
Pzt Films ◽  
Ferroelectric Hysteresis

Lead zirconate titanate (PZT) films with compositions near the morphotropic phase boundary were fabricated on Pt (111)/ Ti / SiO 2/ Si (100) using the triol sol–gel method. The effect of the pre-heating temperature on the phase transformations, microstructures, electrical properties, and ferroelectric properties of the PZT thin films was investigated. Randomly oriented PZT thin films pre-heated at 400°C for 10 min and annealed at 600°C for 30 min showed well-defined ferroelectric hysteresis loops with a remnant polarization of 26.57 μC/cm2 and a coercive field of 115.42 kV/cm. The dielectric constant and dielectric loss of the PZT films were 621 and 0.0395, respectively. The microstructures of the thin films are dense, crack-free, and homogeneous with fine grains about 15–20 nm in size.

scholarly journals Microstructure and Properties of PZT Films with Different PbO Content—Ionic Mechanism of Built-In Fields Formation

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2926 ◽  
Author(s):  
Nikolay Mukhin ◽  
Dmitry Chigirev ◽  
Liubov Bakhchova ◽  
Andrey Tumarkin
Keyword(s):  
Lead Zirconate Titanate ◽  
Lead Oxide ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Experimental Studies ◽  
Rf Magnetron Sputtering ◽  
Lead Zirconate ◽  
Heterophase Structure ◽  
Pzt Films ◽  
A Charge

Experimental studies were conducted on the effects of lead oxide on the microstructure and the ferroelectric properties of lead zirconate-titanate (PZT) films obtained by the method of radio frequency (RF) magnetron sputtering of a ceramic PZT target and PbO2 powder with subsequent heat treatment. It is shown that the change in ferroelectric properties of polycrystalline PZT films is attributable to their heterophase structure with impurities of lead oxide. It is also shown that, even in the original stoichiometric PZT film, under certain conditions (temperature above 580 °C, duration greater than 70 min), impurities of lead oxide may be formed. The presence of a sublayer of lead oxide leads to a denser formation of crystallization centers of the perovskite phase, resulting in a reduction of the grain size as well as the emergence of a charge on the lower interface. The formation of the perovskite structure under high-temperature annealing is accompanied by the diffusion of lead into the surface of the film. Also shown is the effect of the lead ions segregation on the formation of the self-polarized state of thin PZT films.

Issues in the Flexible Integration of Sputter-Deposited PZT Thin Films with Polysilicon and Ti/Pt Electrode Layers for Use as Sensors and Actuators in Microelectromechanical Systems (MEMS)

2000 ◽  
Vol 657 ◽  
Author(s):  
C.F. Knollenberg ◽  
T.D. Sands ◽  
A.S. Nickles ◽  
R.M. White
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Microelectromechanical Systems ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Pt Electrode ◽  
Electrode Layer ◽  
Pzt Thin Films ◽  
Pzt Films ◽  
Sputter Deposited

ABSTRACTSputter-deposited piezoelectric lead zirconate titanate (PZT) thin films with Ti/Pt and polysilicon electrode layers are being investigated for use in Microelectromechanical Systems (MEMS). Existing research shows the nucleation of the perovskite phase of the PZT is linked to the lattice spacing of the underlying Pt electrode and/or seed layers, and is key in obtaining PZT layers with good piezoelectric/ferroelectric properties. Our research with piezoelectric PZT films on Ti/Pt electrode layers aims at employing these films to generate and receive acoustic waves in flexural plate wave devices (FPWs). Our experiments indicate the formation of a random polycrystalline perovskite phase is linked to the emergence of oriented <100> Pt grains within the dominant <111>-oriented crystal structure during rapid thermal annealing in an oxygen environment. Pt films annealed in nitrogen, in contrast, retained their <111> preferential orientation without the formation of Pt <100> grains. PZT films deposited on these electrodes and annealed in nitrogen were strongly oriented in the <111> direction, but exhibited lossy ferroelectric behavior and were prone to delamination. We are also investigating the feasibility of using doped polysilicon electrode layers with PZT thin films. The multiple layers used with the Pt electrode (Pt, Ti, and SiO2 adhesion layer) have significant interactions with one another, and replacing these layers with a single electrode layer should alleviate these complications. A low-temperature PZT deposition process (300°C) and short annealing cycles (30 sec.), coupled with a TiO2 barrier/seed layer should prevent interdiffusion and reactions between the polysilicon and PZT layers. Our experiments show that PZT films deposited and annealed on doped polysilicon layers develop a random polycrystalline perovskite phase, but are subject to tensile cracking. The use of polysilicon as an electrode layer should also facilitate the integration of piezoelectric PZT layers with polysilicon surface micromachined structures using SiGe sacrificial layers.

Pzt Thin Films on a Lead Titanate Interlayer Prepared by rf Magnetron Sputering

1993 ◽  
Vol 310 ◽  
Author(s):  
P. H. Ansari ◽  
A. Safari
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Lead Titanate ◽  
Silicon Oxide ◽  
Perovskite Phase ◽  
Dissipation Factor ◽  
Lead Zirconate ◽  
Si Substrate ◽  
Pzt Thin Films ◽  
Pzt Films

AbstractFerroelectric lead zirconate titanate (PZT) films with a composition near the morphotropic phase boundary have been deposited by if magnetron sputtering on a Si substrate coated with silicon oxide, titanium, and platinum (Si/SiO2/Ti/Pt). Substrate temperature and oxygen partial pressure were changed during deposition to prepare films with controlled stoichiometry and perovskite structure. The effects of lead titanate (PT) as a buffer layer were investigated. Thin films of PT/PZT have a dielectric constant of 800 with a dissipation factor of 0.04 at 1 kHz. The remnant polarization of 8μC/cm2 and the coercive field of 50 kV/cm were measured. The effect of processing on the formation of perovskite phase and the electrical properties will be discussed.

Phase transformations in rapid thermal processed lead zirconate titanate

1995 ◽  
Vol 10 (12) ◽  
pp. 3149-3159 ◽  
Author(s):  
Ellen M. Griswold ◽  
L. Weaver ◽  
M. Sayer ◽  
I.D. Calder
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Perovskite Phase ◽  
Sol Gel ◽  
Pyrochlore Phase ◽  
Lead Zirconate ◽  
Grain Structure ◽  
Avrami Model ◽  
Pzt Thin Films ◽  
Zirconate Titanate

The crystallization kinetics of the pyrochlore to perovskite phase transformation in lead zirconate titanate (PZT) thin films have been analyzed using rapid thermal processing (RTP). Sol-gel PZT thin films, fabricated on platinum electrodes, were annealed at 550 °C to 650 °C with hold times ranging from 1 s to 5 min. Glancing angle x-ray diffraction (XRD) was used for depth profiling to identify the location of phases in the films. Transmission electron microscopy (TEM) provided information on grain structure, nucleation, and growth. The phase information was correlated to the ferroelectric and dielectric properties. The perovskite phase nucleated in the pyrochlore phase throughout the film thickness, and at 650 °C the transformation was complete in 15 s. Fast growing (100) PZT nucleated at the platinum and consumed a small-grained matrix until a columnar structure was obtained. A ramp rate of 100 °C/s was sufficiently fast to prevent transformation during heating and allowed the direct application of an Avrami model for transformation kinetics. An activation energy of 610 kJ/mol was determined.

scholarly journals Effect of Ni/Nb on structure, electrical and ferroelectric properties of 0.5PNN-0.5PZT ceramics

2015 ◽  
Vol 9 (1) ◽  
pp. 1-9 ◽  
Author(s):  
Rashmi Gupta ◽  
Seema Verma ◽  
Deepa Singh ◽  
Karan Singh ◽  
Krishen Bamzai
Keyword(s):  
Grain Size ◽  
Dielectric Relaxation ◽  
Lead Zirconate Titanate ◽  
Remnant Polarization ◽  
Inverse Relationship ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Lead Zirconate ◽  
Cole Plot ◽  
Conventional Solid State Reaction

The solid solutions of lead nickel niobate (PNN) and lead zirconate titanate (PZT), with general formula 0.5 Pb(NixNb1-x)O3-0.5 PZT, where x = 1/3, 1/2 and 2/3 and Zr/Ti = 50/50, were prepared by conventional solid state reaction technique. The perovskite phase formation and morphology were examined by powder X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. From microstructure investigations, the grain size was found to lie in the range of 0.2-1.1 ?m. Diffuse phase transition and dielectric relaxation was obtained for all three compositions. The nature of dielectric relaxation was investigated through complex plane Argand plot or Cole-Cole plot. It was found that both grains as well as grain boundary contribute to dielectric relaxation. A direct correlation between the grain size and electrical properties was obtained. The remnant polarization and grain size were found to follow the inverse relationship. The inverse relationship between remnant polarization and grain size was established.

Preparation of pzt thin films on Pt/Ti/SiO2 and Pt/SiO2 Substrates by ECR Plasma Enhanced DC Magnetron Multi-target Reactive Sputtering

1996 ◽  
Vol 441 ◽  
Author(s):  
Sung-Tae Kim ◽  
Hyun-Ho Kim ◽  
Moon-Yong Lee ◽  
Won-Jong Lee
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Electron Cyclotron Resonance ◽  
Perovskite Phase ◽  
Early Stage ◽  
Reactive Sputtering ◽  
Deposition Process ◽  
Pzt Thin Films ◽  
Si Substrates ◽  
Ecr Plasma

AbstractPerovskite-phase lead zirconate titanate (PZT) thin films were fabricated at 4751C by the electron cyclotron resonance (ECR) plasma enhanced DC magnetron multi-target reactive sputtering method on Pt/Ti/SiO2/Si and Pt/SiO2/Si substrates. Stoichiometric perovskite PZT films were readily obtained on Pt/Ti/SiO2/Si substrates because Ti atoms which were out-diffused to the Pt surface facilitated Pb incorporation by forming lead titanate at the early stage of deposition process. Activation of oxygen by ECR plasma facilitated the oxidation reaction and Pb incorporation into the film. Thus perovskite-phase PZT can be obtained on the Pt/SiO2/Si substrate.

Effect of Barium Titanate Additives on Dielectric Property of PLZT Ceramics

2015 ◽  
Vol 804 ◽  
pp. 21-24
Author(s):  
Ladapak Chumprasert ◽  
Narit Funsueb ◽  
Apichart Limpichaipanit ◽  
Athipong Ngamjarurojana
Keyword(s):  
Barium Titanate ◽  
Lead Zirconate Titanate ◽  
Perovskite Phase ◽  
Ferroelectric Properties ◽  
Lead Zirconate ◽  
Dielectric Behavior ◽  
Rhombohedral Structure ◽  
Soaking Time ◽  
Oxide Powders ◽  
Formation And Evolution

Barium titanate (BT) additive in lanthanum modified lead zirconate titanate (PLZT) was used to modify the microstructure and resultant properties of (1-x) PLZT– x BT where x= 0, 0.05, 0.10, 0.15, 0.20 and 0.25. Oxide powders were synthesized by mixed oxide synthetic route via a rapid vibro-milling technique. All of samples were sintered at 1275°C with the soaking time of 4 h. The ceramic samples were investigated for phase formation and evolution, dielectric behavior and ferroelectric properties. Introduction of BT in PLZT lattice resulted in ferroelectric tetragonal-rhombohedral structure, and further increase of BT content resulted in stabilizing the ferroelectric tetragonal perovskite phase. Dielectric behavior and ferroelectric properties were examined as a function of BT content.

Sign in / Sign up

Export Citation Format

Share Document