The Design of Gm-C Low-Pass Filter for Micromachined Gyroscope

2014 ◽  
Vol 609-610 ◽  
pp. 1072-1076
Author(s):  
Qiu Ye Lv ◽  
Chong He ◽  
Wen Jie Fan ◽  
Yu Feng Zhang ◽  
Xiao Wei Liu
Keyword(s):  
Process Model ◽  
Stop Band ◽  
Cutoff Frequency ◽  
Harmonic Distortion ◽  
Cmos Process ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass ◽  
Simulation Results ◽  
Micromachined Gyroscope

In this Paper, a 4th-Order Low-Pass Gm-C Filter is Presented. for the Design of Operational Tranconductance Amplifier(OTA), it Adopts the Techniques of Current Division and Current Cancellation. these Techniques can Help to Achieve a Low Transconductance Value. for the Architecture of the 4th-Order Gm-C Filter, it Consists of Two Biquads. the Two Biquads are Cascade Connected. the Gm-C Low-Pass Filter has been Implemented under 0.5 μm CMOS Process Model. the Final Simulation Results Show the Cutoff Frequency of the Filter is 100Hz and the Stop-Band Attenuation is Larger than 60dB. the Power Consumption is Lower than 1mW and the Total Harmonic Distortion(THD) is -55dB.

Design and Simulation of Switched Capacitor Filter for Speed Change Parameter Converter

2013 ◽  
Vol 562-565 ◽  
pp. 1132-1136
Author(s):  
Xiao Wei Liu ◽  
Jian Yang ◽  
Song Chen ◽  
Liang Liu ◽  
Rui Zhang ◽  
...  
Keyword(s):  
Stop Band ◽  
Cutoff Frequency ◽  
Rapid Change ◽  
Pass Band ◽  
Cmos Process ◽  
Switched Capacitor ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass ◽  
The Time Domain

In this paper, we design a high-order switched capacitor filter for rapid change parameter converter. This design uses a structure which consists of three biquads filter sub-units. The design is a 6th-order SC elliptic low-pass filter, and the sample frequency is 250 kHz. By the MATLAB Simulink simulation, the system can meet the design requirements in the time domain. In this paper, the 6th-order switched capacitor elliptic low-pass filter was implemented under 0.5 um CMOS process and simulated in Cadence. The final simulation results show that the pass-band cutoff frequency is 10 kHz, and the maximum pass-band ripple is about 0.106 dB. The stop-band cutoff frequency is 20 kHz, and the minimum stop-band attenuation is 74.78 dB.

A CMOS Fourth-Order 150Hz Low-Pass Filter for Sensor Applications

2013 ◽  
Vol 380-384 ◽  
pp. 3320-3323
Author(s):  
Chang Chun Dong ◽  
Nan Nan Liu ◽  
Zhan Peng Jiang
Keyword(s):  
Fourth Order ◽  
Cutoff Frequency ◽  
Cmos Process ◽  
Sensor Interface ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Sensor Applications ◽  
Low Pass ◽  
Cascade Structure ◽  
Simulation Results

A low-pass filter for the sensor is presented, which based on the linearized transconductance structure and the capacitance scaler schemes. The filter adopt fourth order cascade structure, and simulation by 0.5μm CMOS process. Simulation results for the filter show a cutoff frequency of 150Hz, while band ripple is less than 0.8 dB. The power consumption for the filter is only 1.6mW, meet the requirements of the sensor interface ASIC for low-pass filter.

scholarly journals Wideband Reconfigurable Integrated Low-Pass Filter for 5G Compatible Software Defined Radio Solutions

Electronics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 734
Author(s):  
Karolis Kiela ◽  
Marijan Jurgo ◽  
Vytautas Macaitis ◽  
Romualdas Navickas
Keyword(s):  
Software Defined Radio ◽  
Dynamic Range ◽  
Noise Figure ◽  
Harmonic Distortion ◽  
Cmos Process ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Filter Performance ◽  
Low Pass ◽  
Bandwidth Tuning

This article presents a wideband reconfigurable integrated low-pass filter (LPF) for 5G NR compatible software-defined radio (SDR) solutions. The filter uses Active-RC topology to achieve high linearity performance. Its bandwidth can be tuned from 2.5 MHz to 200 MHz, which corresponds to a tuning ratio of 92.8. The order of the filter can be changed between the 2nd, 4th, or 6th order; it has built-in process, voltage, and temperature (PVT) compensation with a tuning range of ±42%; and power management features for optimization of the filter performance across its entire range of bandwidth tuning. Across its entire order, bandwidth, and power configuration range, the filter achieves in-band input-referred third-order intercept point (IIP3) between 32.7 dBm and 45.8 dBm, spurious free dynamic range (SFDR) between 63.6 dB and 79.5 dB, 1 dB compression point (P1dB) between 9.9 dBm and 14.1 dBm, total harmonic distortion (THD) between −85.6 dB and −64.5 dB, noise figure (NF) between 25.9 dB and 31.8 dB and power dissipation between 1.19 mW and 73.4 mW. The LPF was designed and verified using 65 nm CMOS process; it occupies a 0.429 mm2 area of silicon and uses a 1.2 V supply.

scholarly journals An Area-Efficient and Highly Linear Reconfigurable Continuous-Time Filter for Biomedical Sensor Applications

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 2065 ◽  
Author(s):  
Jinyong Zhang ◽  
Shing-Chow Chan ◽  
Hui Li ◽  
Nannan Zhang ◽  
Lei Wang
Keyword(s):  
Continuous Time ◽  
Frequency Tuning ◽  
Cutoff Frequency ◽  
Harmonic Distortion ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Current Steering ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Silicon Area

This paper proposes a compact, high-linearity, and reconfigurable continuous-time filter with a wide frequency-tuning capability for biopotential conditioning. It uses an active filter topology and a new operational-transconductance-amplifier (OTA)-based current-steering (CS) integrator. Consequently, a large time constant τ , good linearity, and linear bandwidth tuning could be achieved in the presented filter with a small silicon area. The proposed filter has a reconfigurable structure that can be operated as a low-pass filter (LPF) or a notch filter (NF) for different purposes. Based on the novel topology, the filter can be readily implemented monolithically and a prototype circuit was fabricated in the 0.18 μm standard complementary-metal–oxide–semiconductor (CMOS) process. It occupied a small area of 0.068 mm2 and consumed 25 μW from a 1.8 V supply. Measurement results show that the cutoff frequency of the LPF could be linearly tuned from 0.05 Hz to 300 Hz and the total-harmonic-distortion (THD) was less than −76 dB for a 2 Hz, 200 mVpp sine input. The input-referred noises were 5.5 μVrms and 6.4 μVrms for the LPF and NF, respectively. A comparison with conventional designs reveals that the proposed design achieved the lowest harmonic distortion and smallest on-chip capacitor. Moreover, its ultra-low cutoff frequency and relatively linear frequency tuning capability make it an attractive solution as an analog front-end for biopotential acquisitions.

scholarly journals Improvement in Cutoff Frequency of Microstrip Butterworth Low Pass Filter using DGS Technique

2019 ◽  
Vol 9 (2) ◽  
pp. 1121-1124
Keyword(s):  
Stop Band ◽  
Cutoff Frequency ◽  
Ground Surface ◽  
Pass Band ◽  
Defected Ground Structure ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Compact Size ◽  
Low Pass ◽  
Sharp Rejection

This paper presents the design, analysis and fabrication of Butterworth Low pass filter with sharp rejection response using defected ground surface technique. The work is carried out to design a low pass filter with cut-off frequency 2.5 GHz to achieved the broad frequency response; the first step is to make a rectangle of 10x10mm at ground surface and the equivalent circuit for the DGS, subsequently followed to consequent L-C parameters extraction using analysis of S parameters response (EM simulation). The designed Butterworth low pass filter is realized and optimized using DGS (Defected Ground Structure) to attain a compact size, satisfactory transition sharpness along with low insertion loss in pass band and wide rejection in the stop band. The fabricated device showed the good conformity with theoretical and VNA measured result.

Novel Low-Pass Microwave Filter Based on Rectangular Ring DGS

2013 ◽  
Vol 273 ◽  
pp. 371-374
Author(s):  
Bao Ping Li ◽  
Yan Liang Zhang
Keyword(s):  
Stop Band ◽  
Center Frequency ◽  
Pass Band ◽  
Band Pass Filter ◽  
Defected Ground Structure ◽  
Ground Structure ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Compact Size ◽  
Low Pass

Due to the frequency response periodicity of distributed transmission line, microstrip band-pass filter usually produces parasitic pass-band and outputs harmonics away from the center frequency of main pass-band. Based on the study of rectangular ring defected ground structure, a 5-order microstrip LPF(low-pass filter) was designed using the single-pole band-stop and slow-wave characteristics of the rectangular ring DGS(Defected Ground Structure) and SISS(Step-Impedance Shunt Stub) structure. Compared with traditional LPF, this LPF presents the advantages of compact size, low insertion loss, broad stop-band and high steep. It also validates the requirements of miniaturization and high performance for filters.

Improved Stator Flux Estimation for Direct Torque Control of Induction Motor Drives

2016 ◽  
Vol 7 (4) ◽  
pp. 1049
Author(s):  
Yahya Ahmed Alamri ◽  
Nik Rumzi Nik Idris ◽  
Ibrahim Mohd. Alsofyani ◽  
Tole Sutikno
Keyword(s):  
Induction Motor ◽  
Cutoff Frequency ◽  
Direct Torque Control ◽  
Motor Drives ◽  
Torque Control ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass ◽  
Flux Estimation ◽  
Stator Flux

<p>Stator flux estimation using voltage model is basically the integration of the induced stator back electromotive force (emf) signal. In practical implementation the pure integration is replaced by a low pass filter to avoid the DC drift and saturation problems at the integrator output because of the initial condition error and the inevitable DC components in the back emf signal. However, the low pass filter introduces errors in the estimated stator flux which are significant at frequencies near or lower than the cutoff frequency. Also the DC components in the back emf signal are amplified at the low pass filter output by a factor equals to . Therefore, different integration algorithms have been proposed to improve the stator flux estimation at steady state and transient conditions. In this paper a new algorithm for stator flux estimation is proposed for direct torque control (DTC) of induction motor drives. The proposed algorithm is composed of a second order high pass filter and an integrator which can effectively eliminates the effect of the error initial condition and the DC components. The amplitude and phase errors compensation algorithm is selected such that the steady state frequency response amplitude and phase angle are equivalent to that of the pure integrator and the multiplication and division by stator frequency are avoided. Also the cutoff frequency selection is improved; even small value can filter out the DC components in the back emf signal. The simulation results show the improved performance of the induction motor direct torque control drive with the proposed stator flux estimation algorithm. The simulation results are verified by the experimental results.</p>

CMOS Implementation of Current Differencing Operational Amplifier and Its Notch Filter Application

2019 ◽  
Vol 29 (08) ◽  
pp. 2050132
Author(s):  
Muhammed Emin Başak
Keyword(s):  
Operational Amplifier ◽  
Process Model ◽  
Active Element ◽  
Harmonic Distortion ◽  
Notch Filter ◽  
Current Mode ◽  
Monte Carlo Analysis ◽  
Cmos Process ◽  
Band Pass Filter ◽  
Pass Filter

Active elements are fundamental circuits for a wide scope of scientific and industrial processes. Many researchers have examined active devices to implement filters, oscillators, rectifiers, and converters. This paper presents the current differencing operational amplifier (CDOA) as an active element, firstly implemented with CMOS transistors. The input part of this circuit is a current differencing unit and the conventional operational amplifier (Op-Amp) pursues it. A new realization of a notch filter consists of CDOA is suggested. Voltage-mode band-pass filter and current-mode notch filter are presented as a different filter applications. Simulation results using TSMC 0.18-[Formula: see text]m CMOS process model are used to verify the theoretical analyses. The sensitivity, noise, total harmonic distortion (THD) and the Monte Carlo analysis have been performed to demonstrate the effectiveness of the proposed active element and notch filter.

Sign in / Sign up

Export Citation Format

Share Document