Evaluation of Permeability Tests of Surface Layer of Concrete of Various Composition

2016 ◽  
Vol 714 ◽  
pp. 171-178 ◽  
Author(s):  
Petr Misák ◽  
Petr Pőssl ◽  
Dalibor Kocáb ◽  
Iva Rozsypalová ◽  
Tomáš Stavař
Keyword(s):  
Surface Layer ◽  
Building Materials ◽  
Statistical Evaluation ◽  
Concrete Durability ◽  
Test Results ◽  
Statistical Methodology ◽  
Concrete Composition ◽  
Cement Ratio ◽  
Difficult Issue

Concrete is one of the most common building materials and its durability has been observed with increased attention. It can be said that concrete durability is closely connected with permeability and, generally speaking, the quality of its surface layer. Evaluating the quality of the surface layer of concrete is a rather difficult issue which can be addressed in different ways. The authors of this paper focus on three internationally used methods – TPT, GWT and ISAT. The paper sums up the results of the experiment whose goal was to investigate the influence of concrete composition on the outputs of the above-mentioned methods. For the purposes of the experiment, specimens were made using 9 mixtures which differed only in the amount of cement and plasticiser, i.e. water/cement ratio. The experiment was designed and evaluated using the statistical methodology DOE (Design of Experiment). Next, the paper discusses a new view of statistical evaluation of test results of the methods described above.

scholarly journals Non-destructive testing of concrete treated with penetrating surface sealant using a Karsten-tube

2018 ◽  
Vol 199 ◽  
pp. 07010
Author(s):  
Sunday O. Nwaubani
Keyword(s):  
Water Uptake ◽  
Initial Moisture Content ◽  
Concrete Surface ◽  
Concrete Durability ◽  
Test Results ◽  
Destructive Testing ◽  
Previously Treated ◽  
Non Destructive ◽  
Exposure Conditions

Surface treatment is increasingly becoming acceptable as a means of ensuring concrete durability by way of controlling or preventing the ingress of various deleterious agents of concrete deterioration. In practice, a combination of non-destructive and semi-destructive evaluation of the concrete surface is often necessary to decide on the need for treatment or re-treatment of previously treated surfaces. The owners of structures and restorers appreciate simple and non-destructive methods in making any interventions on surfaces that have been treated previously. Existing knowledge would suggest that correct interpretation of these test results would depend on an understanding of the effect of factors such as the initial moisture content, quality of the concrete and exposure conditions. This paper presents the result of a study to assess the applicability of the “Karsten-tube” in measuring the water uptake of treated and un-treated concrete surfaces and the effects of the concrete quality, and environmental conditions upon the test results. The results are compared with complementary tests for oxygen permeability and porosity of the concrete specimens studied. Three concrete mixes and five different exposure conditions were investigated. Some specimens were soaked in 3% Sodium Chloride solution to study the effects of aggressive agents. The results indicates that Karsten-tube is a quick non-destructive method for obtaining useful information about the condition of treated and un-treated concrete surfaces and could be used for rapid and reliable assessment of the need for re-treatment of previously treated surfaces. Well-treated surfaces will have low water uptake values, irrespective of the quality of the concrete.

scholarly journals Application of Anodization Process for Cast Aluminium Surface Properties Enhancement

2016 ◽  
Vol 61 (3) ◽  
pp. 1351-1356
Author(s):  
A. Włodarczyk-Fligier ◽  
K. Labisz ◽  
M. Polok-Rubiniec ◽  
J. Konieczny
Keyword(s):  
Corrosion Resistance ◽  
Surface Layer ◽  
Aluminium Alloys ◽  
Light Metal ◽  
Test Results ◽  
Metallographic Examination ◽  
Ceramic Phase ◽  
Treatment Processes ◽  
Anodization Process

Abstract An huge interest is observed in last years in metal matrix composite, mostly light metal based, which have found their applications in many industry branches, among others in the aircraft industry, automotive-, and armaments ones, as well as in electrical engineering and electronics, where one of the most important issue is related to the corrosion resistance, especially on the surface layer of the used aluminium alloys. This elaboration presents the influence of ceramic phase on the corrosion resistance, quality of the surface layer its thickness and structure of an anodic layer formed on aluminium alloys. As test materials it was applied the aluminium alloys Al-Si-Cu and Al-Cu-Mg, for which heat treatment processes and corrosion tests were carried out. It was presented herein grindability test results and metallographic examination, as well. Hardness of the treated alloys with those ones subjected to corrosion process were compared.

Estimation of load-carrying ability of pressure adhesive couplings

2021 ◽  
Vol 0 (3) ◽  
pp. 30-35
Author(s):  
M.A. Lyubchenko ◽  
◽  
O.A. Ryakhovskiy ◽  
A.N. Vorobyev ◽  
G.V. Malysheva ◽  
...  
Keyword(s):  
Surface Layer ◽  
Mechanical Strength ◽  
Experimental Test ◽  
Test Results ◽  
Surface Waviness ◽  
Load Carrying ◽  
Surface Layer Quality

The experimental test results of glued-mechanical couplings of shaft — bush made with the use of anaerobic sealants are presented. Quantitative estimations of the surface layer quality of the mating parts were obtained that made possible to estimate values of surface waviness of the shaft and the bush. The methodology of the waviness determination of cylindrical couplings is described. The influence of fit on mechanical strength of the shaft — bush coupling depending on properties of a used anaerobic sealant was established.

scholarly journals Quality of Surface Texture and Mechanical Properties of PLA and PA-Based Material Reinforced with Carbon Fibers Manufactured by FDM and CFF 3D Printing Technologies

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1671
Author(s):  
Mohd Shahneel Saharudin ◽  
Jiri Hajnys ◽  
Tomasz Kozior ◽  
Damian Gogolewski ◽  
Paweł Zmarzły
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Surface Layer ◽  
3D Printing ◽  
Carbon Fibers ◽  
Tensile Tests ◽  
Mechanical Tests ◽  
Uniaxial Tensile ◽  
Test Results

The paper presents the results of mechanical tests of models manufactured with two 3D printing technologies, FDM and CFF. Both technologies use PLA or PA-based materials reinforced with carbon fibers. The work includes both uniaxial tensile tests of the tested materials and metrological measurements of surfaces produced with two 3D printing technologies. The test results showed a significant influence of the type of technology on the strength of the models built and on the quality of the technological surface layer. After the analysis of the parameters of the primary profile, roughness and waviness, it can be clearly stated that the quality of the technological surface layer is much better for the models made with the CFF technology compared to the FDM technology. Furthermore, the tensile strength of the models manufactured of carbon fiber-enriched material is much higher for samples made with CFF technology compared to FDM.

Implementasi Voip Server Berbasis IPV6 Dengan Raspberry PI

2019 ◽  
Vol 9 (01) ◽  
pp. 47-54
Author(s):  
Rabbai San Arif ◽  
Yuli Fitrisia ◽  
Agus Urip Ari Wibowo
Keyword(s):  
Internet Protocol ◽  
Wireless Transmission ◽  
Raspberry Pi ◽  
Test Results ◽  
Average Delay ◽  
Ipv6 Network ◽  
Ip Network ◽  
Selection Of ◽  
Better Than

Voice over Internet Protocol (VoIP) is a telecommunications technology that is able to pass the communication service in Internet Protocol networks so as to allow communicating between users in an IP network. However VoIP technology still has weakness in the Quality of Service (QoS). VOPI weaknesses is affected by the selection of the physical servers used. In this research, VoIP is configured on Linux operating system with Asterisk as VoIP application server and integrated on a Raspberry Pi by using wired and wireless network as the transmission medium. Because of depletion of IPv4 capacity that can be used on the network, it needs to be applied to VoIP system using the IPv6 network protocol with supports devices. The test results by using a wired transmission medium that has obtained are the average delay is 117.851 ms, jitter is 5.796 ms, packet loss is 0.38%, throughput is 962.861 kbps, 8.33% of CPU usage and 59.33% of memory usage. The analysis shows that the wired transmission media is better than the wireless transmission media and wireless-wired.

THE FEATURES OF BIODESTRUCTION PROCESSES OF THE SURFACES OF HYDRAULIC ENGINEERING CONSTRUCTIONS

2017 ◽  
Author(s):  
Marina Vasilenko ◽  
Marina Vasilenko ◽  
Elena Goncharova ◽  
Elena Goncharova ◽  
Yury Rubanov ◽  
...  
Keyword(s):  
Surface Layer ◽  
Environmental Factors ◽  
Food Chain ◽  
Building Materials ◽  
Microbial Growth ◽  
Mineralogical Composition ◽  
Mechanical Action ◽  
Chemical Processes ◽  
Hydraulic Engineering ◽  
Optimal Conditions

The surfaces of building materials of hydrotechnical constructions undergo the process of algae biofouling. The degree of damage depends on the environmental factors that are affect-ed by the level of anthropogenic load areas. Modeling the biofouling process of concrete with algae under laboratory conditions has allowed determining their impact on the building ma-terial, accompanied by changes in chemical and mineralogical composition of the surface of products. The microscopic examination of sample’s surfaces and evaluation of the effective-ness of various ions leaching from building materials shows the results of "algal attack" relat-ed to the acceleration of biodegradation of materials under the influence of aggressive meta-bolic products, mechanical action neoplasms, creating optimal conditions for the development of subsequent aerobic microbial decomposers. To clarify the nature of chemical processes in the system “algocenosis – concrete” the changes of chemical and phase (mineralogical) com-position of the surface layer of concrete sample were studied. The effect that algae produce on hydraulic engineering constructions is due to the fact that these organisms, belonging to phototrophs and standing at the beginning of the food chain, initiate new microbial growth.

Interrater reliability of a method to assess hypothalamic involvement in pediatric adamantinomatous craniopharyngioma

2020 ◽  
Vol 25 (1) ◽  
pp. 37-42 ◽  
Author(s):  
Ros Whelan ◽  
Eric Prince ◽  
David M. Mirsky ◽  
Robert Naftel ◽  
Aashim Bhatia ◽  
...  
Keyword(s):  
Quality Of Life ◽  
Brain Tumors ◽  
Interrater Reliability ◽  
Statistical Evaluation ◽  
Grading System ◽  
Reliability Study ◽  
Postoperative Mri ◽  
Mri Scans ◽  
Adamantinomatous Craniopharyngioma

OBJECTIVEPediatric adamantinomatous craniopharyngiomas (ACPs) are histologically benign brain tumors that confer significant neuroendocrine morbidity. Previous studies have demonstrated that injury to the hypothalamus is associated with worsened quality of life and a shorter lifespan. This insight helps many surgeons define the goals of surgery for patients with ACP. Puget and colleagues proposed a 3-tiered preoperative and postoperative grading system based on the degree of hypothalamic involvement identified on MRI. In a prospective cohort from their institution, the authors found that use of the system to guide operative goals was associated with decreased morbidity. To date, however, the Puget system has not been externally validated. Here, the authors present an interrater reliability study that assesses the generalizability of this system for surgeons planning initial operative intervention for children with craniopharyngiomas.METHODSA panel of 6 experts, consisting of pediatric neurosurgeons and pediatric neuroradiologists, graded 30 preoperative and postoperative MRI scans according to the Puget system. Interrater reliability was calculated using Fleiss’ κ and Krippendorff’s α statistics.RESULTSInterrater reliability in the preoperative context demonstrated moderate agreement (κ = 0.50, α = 0.51). Interrater reliability in the postoperative context was 0.27 for both methods of statistical evaluation.CONCLUSIONSInterrater reliability for the system as defined is moderate. Slight refinements of the Puget MRI grading system, such as collapsing the 3 grades into 2, may improve its reliability, making the system more generalizable.

THE FEATURES OF BIODESTRUCTION PROCESSES OF THE SURFACES OF HYDRAULIC ENGINEERING CONSTRUCTIONS

2017 ◽  
Author(s):  
Marina Vasilenko ◽  
Marina Vasilenko ◽  
Elena Goncharova ◽  
Elena Goncharova ◽  
Yury Rubanov ◽  
...  
Keyword(s):  
Surface Layer ◽  
Environmental Factors ◽  
Food Chain ◽  
Building Materials ◽  
Microbial Growth ◽  
Mineralogical Composition ◽  
Mechanical Action ◽  
Chemical Processes ◽  
Hydraulic Engineering ◽  
Optimal Conditions

The surfaces of building materials of hydrotechnical constructions undergo the process of algae biofouling. The degree of damage depends on the environmental factors that are affect-ed by the level of anthropogenic load areas. Modeling the biofouling process of concrete with algae under laboratory conditions has allowed determining their impact on the building ma-terial, accompanied by changes in chemical and mineralogical composition of the surface of products. The microscopic examination of sample’s surfaces and evaluation of the effective-ness of various ions leaching from building materials shows the results of "algal attack" relat-ed to the acceleration of biodegradation of materials under the influence of aggressive meta-bolic products, mechanical action neoplasms, creating optimal conditions for the development of subsequent aerobic microbial decomposers. To clarify the nature of chemical processes in the system “algocenosis – concrete” the changes of chemical and phase (mineralogical) com-position of the surface layer of concrete sample were studied. The effect that algae produce on hydraulic engineering constructions is due to the fact that these organisms, belonging to phototrophs and standing at the beginning of the food chain, initiate new microbial growth.

Sinonasal effects of external dacryocystorhinostomy

2021 ◽  
pp. 1-4
Author(s):  
H Eyigor ◽  
E A Cetinkaya ◽  
D T Coban ◽  
G Ozturk ◽  
Ö Erdem
Keyword(s):  
Mucociliary Clearance ◽  
Nasal Symptom ◽  
Ciliary Activity ◽  
Test Results ◽  
Saccharine Test ◽  
Significant Difference ◽  
Symptom Scores ◽  
Endoscopic Score ◽  
External Dacryocystorhinostomy

Abstract Objective External dacryocystorhinostomy is thought to cause mucociliary dysfunction by damaging the mucosa, in turn affecting ciliary activity and mucus quality. This study investigated the effect of external dacryocystorhinostomy on sinonasal function. Methods Patients scheduled for unilateral external dacryocystorhinostomy who underwent endoscopic nasal examination and paranasal sinus computed tomography were included in this study. A saccharine test was performed on the planned surgical side and the mucociliary clearance time was determined. The sinonasal quality of life was measured in all patients, pre-operatively and at six months post-operatively, using the Sino-Nasal Outcome Test-22. The Lund–Kennedy endoscopic score was also determined in all patients, both pre- and post-operatively. Results The study comprised 28 patients (22 females and 6 males). A statistically significant difference was found between the pre- and post-operative saccharine test results (p = 0.006), but not between the pre- and post-operative Sino-Nasal Outcome Test-22 scores (p > 0.05). Conclusion This study is one of only a few to investigate the effect of external dacryocystorhinostomy on sinonasal function. The results showed that external dacryocystorhinostomy impairs mucociliary clearance. The surgical procedure is well tolerated and does not significantly change nasal symptom scores.

Sign in / Sign up

Export Citation Format

Share Document