Validation of the Splitting Tensile Strength Formula for Concrete Containing Blast Furnace Slag

2017 ◽  
Vol 744 ◽  
pp. 136-140 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Modafar Ati ◽  
Omar Fawwaz Najm
Keyword(s):  
Tensile Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Cementitious Materials ◽  
Splitting Tensile Strength ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Prediction Formula ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

The adverse environmental impact of the construction industry may be mitigated through the partial replacement of cement with supplementary cementitious materials (SCM). SCMs such as ground granulated blast furnace slag (GGBS), impart many favourable fresh and long-term concrete properties. A study by Mohamed [1] assessed the splitting tensile strength of sustainable self- consolidating concrete in which up to 80% of the cement was partially replaced with ground granulated blast furnace slag (GGBS), and developed a prediction formula for the splitting tensile strength. In this paper, the tensile strength prediction formula developed by Mohamed et al. [1] is benchmarked against formulas proposed in different building codes and validated with additional test results obtained from the literature. The proposed prediction formula showed excellent correlation to experimental data obtained from the literature.

scholarly journals Characterization of Supplementary Cementitious Materials and Fibers to Be Implemented in High Temperature Concretes for Thermal Energy Storage (TES) Application

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5190
Author(s):  
Laura Boquera ◽  
David Pons ◽  
Ana Inés Fernández ◽  
Luisa F. Cabeza
Keyword(s):  
Tensile Strength ◽  
Blast Furnace ◽  
High Temperature ◽  
Blast Furnace Slag ◽  
Steel Slag ◽  
Cementitious Materials ◽  
Iron Silicate ◽  
Supplementary Cementitious Materials ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Six supplementary cementitious materials (SCMs) were identified to be incorporated in concrete exposed to high-temperature cycling conditions within the thermal energy storage literature. The selected SCMs are bauxite, chamotte, ground granulated blast furnace slag, iron silicate, silica fume, and steel slag. A microstructural characterization was carried out through an optical microscope, X-ray diffraction analysis, and FT-IR. Also, a pozzolanic test was performed to study the reaction of SCMs silico-aluminous components. The formation of calcium silica hydrate was observed in all SCMs pozzolanic test. Steel slag, iron silicate, and ground granulated blast furnace slag required further milling to enhance cement reaction. Moreover, the tensile strength of three fibers (polypropylene, steel, and glass fibers) was tested after exposure to an alkalinity environment at ambient temperature during one and three months. Results show an alkaline environment entails a tensile strength decrease in polypropylene and steel fibers, leading to corrosion in the later ones.

scholarly journals Performa Beton Dengan Ground Granulated Blast Furnace Slag Terhadap Sulfate Attack

2020 ◽  
Vol 16 (3) ◽  
pp. 185
Author(s):  
Rizki Amalia Tri Cahyani ◽  
Ernawan Setyono ◽  
Yunan Rusdianto
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Cementitious Materials ◽  
Sulfate Attack ◽  
Supplementary Cementitious Materials ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Serangan sulfat (sulfate attack) termasuk hal yang umum terjadi pada struktur beton, mengingat ion sulfat banyak dijumpai pada tanah, air tanah dan air laut. Peningkatan ketahanan beton melawan sulfat akan berdampak besar pada durabilitas dan umur layan struktur beton. Penambahan supplementary cementitious materials seperti GGBFS (ground granulated blast furnace slag) ke campuran beton telah terbukti memberikan pengaruh positif terhadap durabilitas dan properti mekanis beton. Namun, GGBFS tergolong material yang baru dikembangkan di Indonesia dan potensinya dalam meningkatkan durabilitas beton belum dimanfaatkan secara luas. Berdasarkan hal tersebut, perlu dilakukan investigasi terkait aplikasi GGBFS dan pengaruhnya terhadap durabilitas beton, terutama dalam melawan serangan sulfat. Dalam studi ini, durabilitas beton dengan persentase penggantian GGBFS 30%, 50% dan 70% terhadap total volume binder dievaluasi menggunakan perlakuan siklus basah-kering dalam larutan magnesium sulfat. Tingkat degradasi beton diukur dengan melakukan observasi terhadap perubahan kuat tekan dan massa spesimen akibat serangan sulfat. Hasil penelitian menunjukkan bahwa penggantian GGBFS hingga 50% dari total volume binder dapat meningkatkan ketahanan beton terhadap serangan sulfat, ditunjukkan dengan kehilangan massa dan reduksi kekuatan yang lebih rendah dibandingkan spesimen kontrol dengan 100% semen Portland.

Durability of Normal and Lightweight Aggregate Mortars with Different Supplementary Cementitious Materials

2021 ◽  
Vol 17 ◽  
pp. 271-281
Author(s):  
Efstratios Badogiannis ◽  
Eirhnh Makrinou ◽  
Marianna Fount
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Lightweight Aggregate ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Pumice Sand ◽  
Water To Binder Ratio ◽  
Furnace Slag

A study on the durability parameters of normal and lightweight aggregate mortars, incorporated different supplementary cementitious materials (SCM) is presented. Mortars were prepared using limestone or pumice as aggregates and Metakaolin, Fly ash, Granulated Blast Furnace Slag and Silica Fume, as SCM, that they replaced cement, at 10 % by mass. Ten different mortars, having same water to binder ratio and aggregate to cement volumetric ratio, they were compared mainly in terms of durability. The use of pumice sand was proved to be effective not only to the density of the mortars as it was expected, but also in durability, fulfilling at the same time minimum strength requirements. The addition of the different SCM further enhanced the durability of the mortars, where Metakaolin was found to be the most effective one, especially against chloride’s ingress.

scholarly journals Effect of Polypropylene Fiber, GGBS and Fly Ash over the Strength Aspects of Concrete: A Critical Review

2021 ◽  
Vol 9 (VI) ◽  
pp. 978-983
Author(s):  
Khalid Bashir Mir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Polypropylene Fiber ◽  
Synthetic Fiber ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

In this review study the usage of three different kinds of constructional materials was discussed in detail. The three materials comprised of Ground Granulated Blast Furnace Slag, fly and polypropylene fiber. Ground Granulated Blast Furnace Slag is basically the slag derived after the quenching process of iron slag produced during the processing of iron in iron industry. Fly ash is the waste generated from the coal processing industries and is mainly used in the road constructions works. Polypropylene fiber is a synthetic fiber that has very high tensile strength and flexural strength. This fiber is also known as synthetic fiber as it is mainly used in the synthetic industry. Depending upon the results of previous studies over the usage of these materials various conclusions has been drawn which are as follows. The results of studies related to the usage of Ground Granulated Blast Furnace Slag as partial replacement of cement concluded that the most optimum usage percentage of Ground Granulated Blast Furnace Slag as partial replacement of cement was found to be between 20 percent and 30 percent and beyond this limit the strength of concrete was decreasing. The past studies related to the usage of fly ash as partial replacement of cement shoed that the most optimum usage percentage of fly ash was found to be between 15 percent to 20 percent and beyond this percentage the strength parameters of concrete such as compressive strength, flexural strength and split tensile strength starts declining up to a greater extent. The studies related to the usage of polypropylene fiber showed that the usage of this fiber increases the compressive strength of soil and the most optimum results were found between 1.0 percent to 1.5 percent usages of polypropylene fiber. Above this percentage there will be negative effect on the strength aspects and the compressive strength starts declining.

Ground Granulated Blast Furnace Slag as Partial Replacement of the Binder of High Performance Concrete

2014 ◽  
Vol 1054 ◽  
pp. 90-94 ◽  
Author(s):  
Michal Ženíšek ◽  
Tomáš Vlach ◽  
Lenka Laiblová
Keyword(s):  
Tensile Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
High Performance ◽  
High Performance Concrete ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag ◽  
Reference Mixture ◽  
Original Reference

This article deals with influence of the ground granulated blast furnace slag (GGBS) in the mixture of high performance concrete. It is a powder active addition used in concrete which is characterized certain cementitious properties. Influence of this addition was experimentally verified. In the first series, partial replacement of cement by GGBS was tested. In the second series, GGBS was added to the original reference mixture. Studied parameters were compressive strength, tensile strength and workability. The tests have shown that a partial replacement of the cement by GGBS is possible for achieving the desired workability or if we need to reduce the price of concrete.

scholarly journals Performance of Class F Pulverised Fuel Ash and Ground Granulated Blast Furnace Slag in Ternary Concrete Mixes

2017 ◽  
Vol 2 (6) ◽  
pp. 36
Author(s):  
Jhon Kamau ◽  
Ash Ahmed ◽  
Paul Hirst ◽  
Joseph Kangwa
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Granulated Blast Furnace Slag ◽  
Fuel Ash ◽  
Anthropogenic Carbon ◽  
Process Heating ◽  
Carbon Dioxide Co2 ◽  
Furnace Slag

Cement is the most utilised material after water, and the processes that are involved in making it are energy intensive, contributing to about 7% of the total global anthropogenic carbon dioxide (CO2). Energy efficiency can however be achieved by using Supplementary Cementitious Materials (SCMs) such as Pulverised Fuel Ash (PFA) and Ground Granulated Blast Furnace Slag (GGBS) which demand less process heating and emit fewer levels of CO2. This work examined the advantages of substituting cement using PFA and GGBS in ternary (2 SCMs) concrete at steps of 0%, 5%, 7.5%, 10%, 15%, 20%, 25%, and 30%. It was found that PFA increased the workability of GGBS, whereas GGBS improved the strength of PFA. The densities of the resultant concrete were below those of the 0% replacement as well as those of individual binary (1 SCM) concretes. The tensile strengths of the ternary concrete were lower than those of the binary concretes, whereas the gains in compressive strengths over curing time were higher at lower replacements for the ternary concrete compared with the 0% replacement and the binary concretes, but lower at higher replacements. The findings indicate that PFA and GGBS could be used together to improve the properties of concrete where each falls short.

Sign in / Sign up

Export Citation Format

Share Document