scholarly journals EBSD-Based Techniques for Characterization of Microstructural Restoration Processes during Annealing of Metals Deformed to Large Plastic Strains

2012 ◽  
Vol 715-716 ◽  
pp. 203-210 ◽  
Author(s):  
Andrew Godfrey ◽  
O.V. Mishin ◽  
T.B. Yu
Keyword(s):  
Equal Channel Angular Extrusion ◽  
Electron Backscatter Diffraction ◽  
Dislocation Cell ◽  
Plastic Strains ◽  
High Angle ◽  
Microstructural Refinement ◽  
Before And After ◽  
Backscatter Diffraction ◽  
Misorientation Angles

Some methods for quantitative characterization of the microstructures deformed to large plastic strains both before and after annealing are discussed and illustrated using examples of samples after equal channel angular extrusion and cold-rolling. It is emphasized that the microstructures in such deformed samples exhibit a heterogeneity in the microstructural refinement by high angle boundaries. Based on this, a new parameter describing the fraction of regions containing predominantly low angle boundaries is introduced. This parameter has some advantages over the simpler high angle boundary fraction parameter, in particular with regard to data collected from electron-backscatter diffraction investigations, where boundaries with very low misorientation angles cannot be reliably detected. It is shown how this parameter can be related to the recrystallization behavior. Another parameter, based on mode of the distribution of dislocation cell sizes is outlined, and it is demonstrated how this parameter can be used to investigate the uniformity, or otherwise, of the restoration processes occurring during annealing of metals deformed to large plastic strains.

The Spectrum of Crystallographic Misorientations of Intercrystalline Boundaries for BCC-HCP Phase Transformation in Additively Manufactured Ti-6Al-4V

2021 ◽  
Vol 410 ◽  
pp. 867-871
Author(s):  
Andrey A. Redikultsev ◽  
Stepan I. Stepanov ◽  
Mikhail L. Lobanov
Keyword(s):  
Electron Backscatter Diffraction ◽  
Experimental Spectrum ◽  
High Angle ◽  
Structural And Phase Transformations ◽  
Orientation Microscopy ◽  
Α Phase ◽  
Interphase Boundaries ◽  
Intercrystalline Boundaries ◽  
Backscatter Diffraction ◽  
Misorientation Angles

Electron backscatter diffraction is a modern experimental method for local structure and texture investigation, which makes it possible to establish the presence and types of the various boundaries between the elements of the mesostructure such as low or high angle, special and interphase boundaries. Moreover, this technique can demonstrate the migration of boundaries during structural and phase transformations. This study estimated the possible spectrum of crystallographic misorientations of intercrystalline boundaries in additively manufactured titanium alloy Ti-6Al-4V using orientation microscopy and crystallographic calculations based on Burgers orientation relationship during β→α-transformation. The study has established that the boundaries between grains of α-phase are characterized by the misorientation angles of 11±2 °, 61±5 °, 89±3 °. The majority of high-angle boundaries are characterized by misorientation angles in the range of 57-65 °. The study also ascertained that the experimental spectrum of intercrystalline boundaries in the α-phase reveals the displacive nature of β→α-transformation in titanium alloys.

Crystal orientation of β-Sn grain in Ni(P)/Sn–0.5Cu/Cu and Ni(P)/Sn–1.8Ag/Cu joints

2010 ◽  
Vol 25 (10) ◽  
pp. 1950-1957 ◽  
Author(s):  
Sun-Kyoung Seo ◽  
Moon Gi Cho ◽  
Hyuck Mo Lee
Keyword(s):  
Grain Boundary ◽  
Crystal Orientation ◽  
Electron Backscatter Diffraction ◽  
Boundary Crossing ◽  
High Angle ◽  
Before And After ◽  
Columnar Grains ◽  
Sn Grain Orientation ◽  
Backscatter Diffraction ◽  
Solder Composition

Electron backscatter diffraction analysis was used to compare the crystal orientation of β-Sn grains in Ni(P)/Sn–0.5Cu/Cu and Ni(P)/Sn–1.8Ag/Cu joints before and after aging. In Ni(P)/solder/Cu joints, the solder composition (Cu versus Ag) significantly affects β-Sn grain orientation. In Ni(P)/Sn–0.5Cu/Cu, there are two types of small columnar grains grown from Ni(P) and Cu under bump metallurgy with a high-angle grain boundary crossing the joint closer to the Ni side; in contrast, Ni(P)/Sn–1.8Ag/Cu has large grains with low-angle boundaries. During thermal aging at 150 °C for 250 h, the Ni(P)/Sn–0.5Cu/Cu joints undergo a more significant microstructural change than the Ni(P)/Sn–1.8Ag/Cu joint. Additionally, obvious ledges developed along the high-angle grain boundary between the upper and lower areas in the Sn–0.5Cu joint.

scholarly journals Comparative Study of Microstructural Characteristics and Hardness of β-Quenched Zr702 and Zr–2.5Nb Alloys

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3752 ◽  
Author(s):  
Jiahong Dai ◽  
Haotian Guan ◽  
Linjiang Chai ◽  
Kang Xiang ◽  
Yufan Zhu ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Electron Backscatter Diffraction ◽  
Microstructural Characteristics ◽  
Plate Structures ◽  
Average Width ◽  
Before And After ◽  
Quantitative Analyses ◽  
Backscatter Diffraction ◽  
Equiaxed Grains ◽  
Misorientation Angles

In this study, two commercial Zr alloys (Zr702 and Zr–2.5Nb) were subjected to the same β-quenching treatment (water cooling after annealing at 1000 °C for 10 min). Their microstructural characteristics and hardness before and after the heat treatment were well characterized and compared by electron channel contrast (ECC) imaging, electron backscatter diffraction (EBSD) techniques, and microhardness measurements. Results show that after the β quenching, prior equiaxed grains in Zr702 are transformed into Widmanstätten plate structures (the average width ~0.8 μm) with many fine precipitates distributed along their boundaries, while the initial dual-phase (α + β) microstructure in Zr–2.5Nb is fully replaced by fine twinned martensitic plates (the average width ~0.31 μm). Differences in alloying elements (especially Nb) between Zr702 and Zr–2.5Nb are demonstrated to play a key role in determining their phase transformation behaviors during the β quenching. Analyses on crystallographic orientations show that the Burgers orientation relationship is well obeyed in both the alloys with misorientation angles between α plates essentially focused on ~60°. After β quenching, the hardnesses of both alloys were increased by ~35%–40%. Quantitative analyses using the Hall–Petch equation suggest that such an increase was mainly attributable to phase transformation-induced grain refinements. Since Nb is able to effectively refine the β-quenched structures, a higher hardness increment is produced in Zr–2.5Nb than in Zr702.

scholarly journals Analysis of Strain Partitioning in Intercritically Deformed Microstructures via Interrupted Tensile Tests

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 112
Author(s):  
Unai Mayo ◽  
Nerea Isasti ◽  
José M. Rodríguez-Ibabe ◽  
Pello Uranga
Keyword(s):  
Electron Backscatter Diffraction ◽  
Tensile Tests ◽  
Correlation Technique ◽  
Strain Partitioning ◽  
High Angle ◽  
Electron Backscatter ◽  
Different Types ◽  
Final Deformation ◽  
Micro Alloyed Steel ◽  
Backscatter Diffraction

Intercritically deformed steels present combinations of different types of ferrite, such as deformed ferrite (DF) and non-deformed ferrite (NDF) grains, which are transformed during the final deformation passes and final cooling step. Recently, a grain identification and correlation technique based on EBSD has been employed together with a discretization methodology, enabling a distinction to be drawn between different ferrite populations (NDF and DF grains). This paper presents a combination of interrupted tensile tests with crystallographic characterization performed by means of Electron Backscatter Diffraction (EBSD), by analyzing the evolution of an intercritically deformed micro-alloyed steel. In addition to this, and using the nanoindentation technique, both ferrite families were characterized micromechanically and the nanohardness was quantified for each population. NDF grains are softer than DF ones, which is related to the presence of a lower fraction of low-angle grain boundaries. The interrupted tensile tests show the different behavior of low- and high-angle grain boundary evolution as well as the strain partitioning in each ferrite family. NDF population accommodates most of the deformation at initial strain intervals, since strain reaches 10%. For higher strains, NDF and DF grains behave similarly to the strain applied.

Application of Electron Backscatter Diffraction for Crystallographic Characterization of Tin Whiskers

2012 ◽  
Vol 18 (4) ◽  
pp. 876-884 ◽  
Author(s):  
Joseph R. Michael ◽  
Bonnie B. McKenzie ◽  
Donald F. Susan
Keyword(s):  
Electron Backscatter Diffraction ◽  
Growth Direction ◽  
Tin Whiskers ◽  
Physical Growth ◽  
Final Choice ◽  
Advantages And Disadvantages ◽  
Electron Backscatter ◽  
Backscatter Diffraction

AbstractUnderstanding the growth of whiskers or high aspect ratio features on substrates can be aided when the crystallography of the feature is known. This study has evaluated three methods that utilize electron backscatter diffraction (EBSD) for the determination of the crystallographic growth direction of an individual whisker. EBSD has traditionally been a technique applied to planar, polished samples, and thus the use of EBSD for out-of-surface features is somewhat more difficult and requires additional steps. One of the methods requires the whiskers to be removed from the substrate resulting in the loss of valuable physical growth relationships between the whisker and the substrate. The other two techniques do not suffer this disadvantage and provide the physical growth information as well as the crystallographic growth directions. The final choice of method depends on the information required. The accuracy and the advantages and disadvantages of each method are discussed.

scholarly journals Application of Electron Backscatter Diffraction (EBSD) for Crystallographic Characterization of Aluminum-Doped Zinc Oxide Sputtered Films

2013 ◽  
Vol 19 (S4) ◽  
pp. 103-104
Author(s):  
C.B. Garcia ◽  
E. Ariza ◽  
C.J. Tavares
Keyword(s):  
Electron Microscopy ◽  
Grain Size ◽  
Zinc Oxide ◽  
Electron Backscatter Diffraction ◽  
Wide Range ◽  
Electron Backscatter ◽  
Aluminum Doped Zinc Oxide ◽  
Ebsd Technique ◽  
Backscatter Diffraction

Zinc Oxide is a wide band-gap compound semiconductor that has been used in optoelectronic and photovoltaic applications due to its good electrical and optical properties. Aluminium has been an efficient n-type dopant for ZnO to produce low resistivity films and high transparency to visible light. In addition, the improvement of these properties also depends on the morphology, crystalline structure and deposition parameters. In this work, ZnO:Al films were produced by d.c. pulsed magnetron sputtering deposition from a ZnO ceramic target (2.0 wt% Al2O3) on glass substrates, at a temperature of 250 ºC.The crystallographic orientation of aluminum doped zinc oxide (ZnO:Al) thin films has been studied by Electron Backscatter Diffraction (EBSD) technique. EBSD coupled with Scanning Electron Microscopy (SEM) is a powerful tool for the microstructural and crystallographic characterization of a wide range of materials.The investigation by EBSD technique of such films presents some challenges since this analysis requires a flat and smooth surface. This is a necessary condition to avoid any shadow effects during the experiments performed with high tilting conditions (70º). This is also essential to ensure a good control of the three dimensional projection of the crystalline axes on the geometrical references related to the sample.Crystalline texture is described by the inverse pole figure (IPF) maps (Figure 1). Through EBSD analysis it was observed that the external surface of the film presents a strong texture on the basal plane orientation (grains highlighted in red colour). Furthermore it was possible to verify that the grain size strongly depends on the deposition time (Figure 1 (a) and (b)). The electrical and optical film properties improve with increasing of the grain size, which can be mainly, attributed to the decrease in scattering grain boundaries which leads to an increasing in carrier mobility (Figure 2).The authors kindly acknowledge the financial support from the Portuguese Foundation for Science and Technology (FCT) scientific program for the National Network of Electron Microscopy (RNME) EDE/1511/RME/2005.

scholarly journals Characterization of Coarse-Grained Heat-Affected Zones in Al and Ti-Deoxidized Offshore Steels

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1096
Author(s):  
Henri Tervo ◽  
Antti Kaijalainen ◽  
Vahid Javaheri ◽  
Satish Kolli ◽  
Tuomas Alatarvas ◽  
...  
Keyword(s):  
Prior Austenite ◽  
Electron Backscatter Diffraction ◽  
Coarse Grained ◽  
Grain Coarsening ◽  
Austenite Grain ◽  
The Matrix ◽  
Backscatter Diffraction ◽  
Prior Austenite Grain ◽  
Deoxidation Practice

Deterioration of the toughness in heat-affected zones (HAZs) due to the thermal cycles caused by welding is a known problem in offshore steels. Acicular ferrite (AF) in the HAZ is generally considered beneficial regarding the toughness. Three experimental steels were studied in order to find optimal conditions for the AF formation in the coarse-grained heat-affected zone (CGHAZ). One of the steels was Al-deoxidized, while the other two were Ti-deoxidized. The main focus was to distinguish whether the deoxidation practice affected the AF formation in the simulated CGHAZ. First, two different peak temperatures and prolonged annealing were used to study the prior austenite grain coarsening. Then, the effect of welding heat input was studied by applying three cooling times from 800 °C to 500 °C in a Gleeble thermomechanical simulator. The materials were characterized using electron microscopy, energy-dispersive X-ray spectrometry, and electron backscatter diffraction. The Mn depletion along the matrix-particle interface was modelled and measured. It was found that AF formed in the simulated CGHAZ of one of the Ti-deoxidized steels and its fraction increased with increasing cooling time. In this steel, the inclusions consisted mainly of small (1–4 μm) TiOx-MnS, and the tendency for prior austenite grain coarsening was the highest.

Use of Electron Backscatter Diffraction Technique in Characterization of 6XXX Aluminum Alloy Extrusions

2000 ◽  
Vol 6 (S2) ◽  
pp. 954-955
Author(s):  
Steven R. Claves ◽  
Wojciech Z. Misiolek ◽  
William H. Van Geertruyden ◽  
David B. Williams
Keyword(s):  
Electron Backscatter Diffraction ◽  
Metal Flow ◽  
Extrusion Process ◽  
Cross Sectional ◽  
Electron Backscattering Diffraction ◽  
Electron Backscatter ◽  
Individual Grains ◽  
Backscatter Diffraction ◽  
6Xxx Series

Electron Backscattering Diffraction (EBSD) is an important tool for analyzing the crystal grain orientation of a microstructure and can be used to formulate conclusions about microtexture, texture determined from individual grains. This technique has been used to study a 6xxx series aluminum alloy's response to the deformation of the extrusion process. Extrusion is the process by which a billet of material is forced, under high pressure, through a die. The material undergoes a significant decrease in cross sectional area, and is formed into a shape equivalent to the geometry of the die orifice. Different bearing lands are shown in shown in Figure 1. These surfaces form the part, and are designed to control the metal flow making it uniform through the die, thus yielding good mechanical properties. This research was focused on the resultant microstructure. The shaded regions of Figure 2 show the two surface regions where EBSD measurements were taken.

Sign in / Sign up

Export Citation Format

Share Document