Surface Finish Techniques for FDM Parts

2015 ◽  
Vol 818 ◽  
pp. 45-48 ◽  
Author(s):  
Ivan Gajdoš ◽  
Emil Spišák ◽  
Luboš Kaščák ◽  
Volodymyr Krasinskyi
Keyword(s):  
Surface Finish ◽  
Fused Deposition Modeling ◽  
Engineering Industry ◽  
Surface Finishing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Pre Treatment ◽  
Manufacturing Technologies ◽  
The Impact

Additive manufacturing technologies decrease production time and costs in engineering industry but also in other industries. Parts produced with Fused Deposition Modeling (FDM) have typical low surface finish quality. This paper is aimed on research of surface finishing technologies applicable to improve the quality of FDM prototypes surface finish. Pretreated samples were blasted with sodium bicarbonate and glass beads. The values of Raand Rzwere measured on the samples and compared the impact of selected pre-treatment, blasting medium and blasting conditions on surface finish quality of FDM prototypes.

scholarly journals Analysis of the surface quality of polycaprolactam 3D prints enriched with carbon and glass fiber

2021 ◽  
Vol 338 ◽  
pp. 01005
Author(s):  
Damian Dzienniak ◽  
Jan Pawlik
Keyword(s):  
Glass Fiber ◽  
Surface Quality ◽  
Fused Deposition Modeling ◽  
Polyamide 6 ◽  
Fiber Glass ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact ◽  
The Relationship

Additive manufacturing has been gaining popularity and availability year by year, which has resulted in its dynamic development. The most common 3D printing method as of today, FDM (Fused Deposition Modeling), owing to its peculiarity, does not always guarantee producing objects with low surface roughness. The authors of the present article have taken on the analysis of the impact of FDM printing on the roughness of the filament thus processed. They also investigate the relationship between the roughness of the unprocessed filament (made of polycaprolactam, that is, polyamide 6 or PA6) with admixtures of other materials (carbon fiber, glass fiber) and the surface quality of the manufactured object. The main subject of the analysis is the side surfaces of 3D prints, as it is their quality that is usually directly dependent on many factors connected with the process of the laying of the consecutive layers. The authors check step by step whether there exists a pronounced relationship between the roughness of the original filament material and the roughness of the obtained surface.

scholarly journals Automated Testing and Characterization of Additive Manufacturing (ATCAM)

2021 ◽  
Author(s):  
Arash Alex Mazhari ◽  
Randall Ticknor ◽  
Sean Swei ◽  
Stanley Krzesniak ◽  
Mircea Teodorescu
Keyword(s):  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Cell System ◽  
Automated Testing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Machine Calibration

AbstractThe sensitivity of additive manufacturing (AM) to the variability of feedstock quality, machine calibration, and accuracy drives the need for frequent characterization of fabricated objects for a robust material process. The constant testing is fiscally and logistically intensive, often requiring coupons that are manufactured and tested in independent facilities. As a step toward integrating testing and characterization into the AM process while reducing cost, we propose the automated testing and characterization of AM (ATCAM). ATCAM is configured for fused deposition modeling (FDM) and introduces the concept of dynamic coupons to generate large quantities of basic AM samples. An in situ actuator is printed on the build surface to deploy coupons through impact, which is sensed by a load cell system utilizing machine learning (ML) to correlate AM data. We test ATCAM’s ability to distinguish the quality of three PLA feedstock at differing price points by generating and comparing 3000 dynamic coupons in 10 repetitions of 100 coupon cycles per material. ATCAM correlated the quality of each feedstock and visualized fatigue of in situ actuators over each testing cycle. Three ML algorithms were then compared, with Gradient Boost regression demonstrating a 71% correlation of dynamic coupons to their parent feedstock and provided confidence for the quality of AM data ATCAM generates.

scholarly journals Desain dan Pembuatan Prototype Piston Honda MEGAPRO FI Menggunakan 3D Printing

2020 ◽  
Vol 1 (2) ◽  
pp. 81-91
Author(s):  
Frince Marbun ◽  
Richard A.M. Napitupulu
Keyword(s):  
3D Printing ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Layer By Layer ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Manufacturing Technologies ◽  
Aided Design

3D printing technology has great potential in today's manufacturing world, one of its uses is in making miniatures or prototypes of a product such as a piston. One of the most famous and inexpensive 3D printing (additive manufacturing) technologies is Fused Deposition Modeling (FDM), the principle FDM works by thermoplastic extrusion through a hot nozzle at melting temperature then the product is made layer by layer. The two most commonly used materials are ABS and PLA so it is very important to know the accuracy of product dimensions. FDM 3D Printing Technology is able to make duplicate products accurately using PLA material. FDM machines work by printing parts that have been designed by computer-aided design (CAD) and then exported in the form of STL or .stl files and uploaded to the slicer program to govern the printing press according to the design. Using Anet A8 brand 3D printing tools that are available to the public, Slicing of general CAD geometry files such as autocad and solidwork is the basis for making this object. This software is very important to facilitate the design process to be printed. Some examples of software that can be downloaded and used free of charge such as Repetier-Host and Cura. by changing the parameters in the slicer software is very influential in the 3D printing manufacturing process.

Effect of process parameters on flexural strength and surface roughness in fused deposition modeling of PC-ABS material

2021 ◽  
pp. 251659842110311
Author(s):  
Shrikrishna Pawar ◽  
Dhananjay Dolas1
Keyword(s):  
Surface Roughness ◽  
Flexural Strength ◽  
Response Surface ◽  
Layer Thickness ◽  
Process Parameters ◽  
Surface Finish ◽  
Fused Deposition Modeling ◽  
Build Orientation ◽  
Fused Deposition ◽  
Deposition Modeling

Fused deposition modeling (FDM) is one of the most commonly used additive manufacturing (AM) technologies, which has found application in industries to meet the challenges of design modifications without significant cost increase and time delays. Process parameters largely affect the quality characteristics of AM parts, such as mechanical strength and surface finish. This article aims to optimize the parameters for enhancing flexural strength and surface finish of FDM parts. A total of 18 test specimens of polycarbonate (PC)-ABS (acrylonitrile–butadiene–styrene) material are printed to analyze the effect of process parameters, viz. layer thickness, build orientation, and infill density on flexural strength and surface finish. Empirical models relating process parameters with responses have been developed by using response surface regression and further analyzed by analysis of variance. Main effect plots and interaction plots are drawn to study the individual and combined effect of process parameters on output variables. Response surface methodology was employed to predict the results of flexural strength 48.2910 MPa and surface roughness 3.5826 µm with an optimal setting of parameters of 0.14-mm layer thickness and 100% infill density along with horizontal build orientation. Experimental results confirm infill density and build orientation as highly significant parameters for impacting flexural strength and surface roughness, respectively.

Investigation of Recycled Acrylonitrile Butadiene Styrene for Additive Manufacturing

2020 ◽  
pp. 130-154
Author(s):  
Shajahan Bin Maidin ◽  
Zulkeflee Abdullah ◽  
Ting Kung Hieng
Keyword(s):  
Mechanical Properties ◽  
Test Specimen ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Travel Speed ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Processes ◽  
Butadiene Styrene

One of the disadvantages of fused deposition modeling (FDM) is waste produced during the printing processes. This investigation focuses on using 100% recycled Acrylonitrile Butadiene Styrene (ABS) for the FDM process. The recycling begins with re-granule the waste ABS material and produces it into a new filament. The new recycled filament was used to print the test specimen. Investigation on the mechanical properties and the surface quality of the test specimen and comparison with standard ABS specimen was done. The result shows that the recycled ABS can be produced into filament with 335°C of extrusion temperature and 1.5 mm/s travel speed of the extruder conveyor. The surface roughness of recycled specimen is 6.94% higher than the standard ABS specimen. For ultimate tensile strength, there is a small difference in X and Y orientation between the standard and the recycled ABS specimen which are 22.93% and 19.98%, respectively. However, in Z orientation, it is 52.33% lower. This investigation proves that ABS can be recycled without significantly affecting its mechanical properties.

scholarly journals Parameters Influencing the Outcome of Additive Manufacturing of Tiny Medical Devices Based on PEEK

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 466 ◽  
Author(s):  
Yiqiao Wang ◽  
Wolf-Dieter Müller ◽  
Adam Rumjahn ◽  
Andreas Schwitalla
Keyword(s):  
Medical Devices ◽  
Fused Deposition Modeling ◽  
High Accuracy ◽  
Design Parameters ◽  
Fused Deposition ◽  
Polyether Ether Ketone ◽  
Deposition Modeling ◽  
3D Printed ◽  
Ether Ketone

In this review, we discuss the parameters of fused deposition modeling (FDM) technology used in finished parts made from polyether ether ketone (PEEK) and also the possibility of printing small PEEK parts. The published articles reporting on 3D printed PEEK implants were obtained using PubMed and search engines such as Google Scholar including references cited therein. The results indicate that although many have been experiments conducted on PEEK 3D printing, the consensus on a suitable printing parameter combination has not been reached and optimized parameters for printing worth pursuing. The printing of reproducible tiny-sized PEEK parts with high accuracy has proved to be possible in our experiments. Understanding the relationships among material properties, design parameters, and the ultimate performance of finished objects will be the basis for further improvement of the quality of 3D printed medical devices based on PEEK and to expand the polymers applications.

Effect of layer thickness on irreversible thermal expansion and interlayer strength in fused deposition modeling

2017 ◽  
Vol 23 (5) ◽  
pp. 943-953 ◽  
Author(s):  
Anthony A. D’Amico ◽  
Analise Debaie ◽  
Amy M. Peterson
Keyword(s):  
Mechanical Properties ◽  
Thermal Expansion ◽  
Flexural Strength ◽  
Layer Thickness ◽  
Fused Deposition Modeling ◽  
Thermal Strain ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
The Impact

Purpose The aim of this paper is to examine the impact of layer thickness on irreversible thermal expansion, residual stress and mechanical properties of additively manufactured parts. Design/methodology/approach Samples were printed at several layer thicknesses, and their irreversible thermal expansion, tensile strength and flexural strength were determined. Findings Irreversible thermal strain increases with decreasing layer thickness, up to 22 per cent strain. Tensile and flexural strengths exhibited a peak at a layer thickness of 200 μm although the maximum was not statistically significant at a 95 per cent confidence interval. Tensile strength was 54 to 97 per cent of reported values for injection molded acrylonitrile butadiene styrene (ABS) and 29 to 73 per cent of those reported for bulk ABS. Flexural strength was 18 to 41 per cent of reported flexural strength for bulk ABS. Practical implications The large irreversible thermal strain exhibited that corresponding residual stresses could lead to failure of additively manufactured parts over time. Additionally, the observed irreversible thermal strains could enable thermally responsive shape in additively manufactured parts. Variation in mechanical properties with layer thickness will also affect manufactured parts. Originality/value Tailorable irreversible thermal strain of this magnitude has not been previously reported for additively manufactured parts. This strain occurs in parts made with both high-end and consumer grade fused deposition modeling machines. Additionally, the impact of layer thickness on tensile and flexural properties of additively manufactured parts has received limited attention in the literature.

Development of Rapid Tooling for Investment Casting Using Fused Deposition Modeling Process

2014 ◽  
Vol 970 ◽  
pp. 155-165 ◽  
Author(s):  
Sambasiva Rao Addanki ◽  
Medha A. Dharap ◽  
Jonnalagedda V.L. Venkatesh
Keyword(s):  
Surface Finish ◽  
Chemical Treatment ◽  
Fused Deposition Modeling ◽  
Processing Technique ◽  
Rapid Tooling ◽  
Parent Material ◽  
Fused Deposition ◽  
Good Surface ◽  
Deposition Modeling ◽  
Good Surface Finish

Fused Deposition Modeling (FDM) process can be used to produce the rapid tooling directly or indirectly. However, rapid tooling application demands good surface finish since the poor surface finish of FDM parts has become a limitation for its tool application. So there is need to improve the surface finish of FDM made tools. In this study, surface roughness of FDM tools are drastically reduced by a post processing technique called chemical treatment process. Surface finish was improved by filling the gap between layers by diffusion of parent material. Thus FDM made tools can be used as direct as well as indirect tools after the chemical treatment. Comparative study was made between Silicon Rubber Moulding and FDM Tooling towards the cost, time, life of mould, quality and feasibility aspects. It was found that FDM tooling is more economical, easy to use, reduced cycle time, improved quality, long life of mould and more feasibility towards complex parts etc.

Sign in / Sign up

Export Citation Format

Share Document