Preparation and Characterization of CdSe Nanoparticles Synthesized Using the Ultrasonic Irradiation

2007 ◽  
Vol 124-126 ◽  
pp. 1229-1232 ◽  
Author(s):  
Myoung Seok Sung ◽  
Yoon Bok Lee ◽  
Yong Jin Kim ◽  
Yang Do Kim
Keyword(s):  
Ultrasonic Irradiation ◽  
Photoelectron Spectroscopy ◽  
Irradiation Time ◽  
Xrd Analysis ◽  
Cdse Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Emission ◽  
Transmission Electron ◽  
Average Size

Cadmium selenide(CdSe) nanoparticles were prepared in the aqueous solution containing isopropyl alcohol by the ultrasonic irradiation at room temperature. The cadmium chloride (CdCl2) and sodium selenosulfate (Na2SeSO3) were used as the cadmium and selenium source, respectively. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), UV-Vis absorption spectra and PL spectra were used to characterize the CdSe nanoparticles. XRD analysis revealed the formation of cubic structure CdSe. TEM images showed aggregated CdSe nanoparticles with the size of nanometer scale. Average size of CdSe nanoparticles were about 3.9, 5.0 and 5.1nm with sonication time of 6, 30 and 40 minutes, respectively. The surface emission became less intensive and shifted to red with increasing irradiation time. This paper presents the effects of ultrasonic on the formation of CdSe nanoparticles and its characteristics.

scholarly journals Hydrothermal Synthesis of MnWO4@GO Composite as Non-Precious Electrocatalyst for Urea Oxidation

Nanomaterials ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 85
Author(s):  
Patnamsetty Chidanandha Nagajyothi ◽  
Kisoo Yoo ◽  
Rajavaram Ramaraghavulu ◽  
Jaesool Shim
Keyword(s):  
Electron Microscopy ◽  
Hydrothermal Synthesis ◽  
Photoelectron Spectroscopy ◽  
Xrd Analysis ◽  
Morphological Characterization ◽  
Energy Storage And Conversion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Density Values

In this study, manganese tungstate (MW) and MW/graphene oxide (GO) composites were prepared by a facile hydrothermal synthesis at pH values of 7 and 12. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy were used for the structural, compositional, and morphological characterization of the nanoparticles (NPs). The XRD analysis revealed that the formation of monoclinic MnWO4 did not have impurities. The SEM and TEM analyses showed that the synthesized NPs were rod-shaped and well-distributed on the GO. The as-synthesized samples can be used as electrocatalysts for the urea oxidation reaction (UOR). The MW@GO-12 electrocatalyst exhibited higher current density values compared to other electrocatalysts. This study provides a new platform for synthesizing inexpensive nanocomposites as promising electrocatalysts for energy storage and conversion applications.

scholarly journals Activity and Stability of Trypsin Immobilized onto Chitosan Magnetic Nanoparticles

2017 ◽  
Vol 2017 ◽  
pp. 1-10
Author(s):  
Jun Sun ◽  
Bin Xu ◽  
Yu Shi ◽  
Lin Yang ◽  
Hai-le Ma
Keyword(s):  
Magnetic Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Covalent Immobilization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Immobilized Trypsin ◽  
Alkaline Conditions ◽  
Ph Range ◽  
Average Size

The aim of this study was to develop a thermally and operationally stable trypsin through covalent immobilization onto chitosan magnetic nanoparticles (Fe3O4 @CTS). The successful preparation of the Fe3O4 @CTS nanoparticles was verified by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and transmission electron microscopy (TEM), which indicated that the prepared Fe3O4 @CTS nanoparticles have superparamagnetic properties, with an average size of approximately 17 nm. Then, trypsin was covalently immobilized onto the Fe3O4 @CTS nanoparticles at a high loading capacity (149.25 mg/g). The FTIR data demonstrated that the trypsin had undergone a conformational change compared with free trypsin, and the Michaelis constant (Km) and the maximum hydrolysis reaction rate (Vmax) showed that the trypsin immobilized on the Fe3O4 @CTS had a lower affinity for BAEE and lower activity compared with free trypsin. However, the immobilized trypsin showed higher activity than free trypsin at pH 6.0 and in alkaline conditions and retained more than 84% of its initial activity at 60°C after 8 h incubation. Its excellent performance across a broader pH range and high thermal stability, as well as its effective hydrolysis of bovine serum albumin (BSA) and its reusability, make it more attractive than free trypsin for application in protein digestion.

scholarly journals Synthesis of gold nanoparticles using Platycodon grandiflorum extract and its antipathogenic activity under optimal conditions

2020 ◽  
Vol 10 ◽  
pp. 184798042096169
Author(s):  
Periasamy Anbu ◽  
Subash CB Gopinath ◽  
S Jayanthi
Keyword(s):  
Electron Microscopy ◽  
Gold Nanoparticles ◽  
Plant Extracts ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Platycodon Grandiflorum ◽  
Transmission Electron ◽  
Flower Plant ◽  
Average Size

Gold nanoparticles have many applications in the biomedical field, mainly for drug delivery, cancer therapy, and detection of pathogenic microorganisms. In this study, gold nanoparticles synthesized using Platycodon grandiflorum (Balloon flower plant) extracts were evaluated for their antibacterial potential. Gold nanoparticles were synthesized at 20–50°C using different volumes of the leaf extract. Biosynthesis of gold nanoparticles was confirmed by ultraviolet–visible spectral absorption at 545 nm by surface plasmon resonance. The morphology and size of the P. grandiflorum gold nanoparticles were further characterized as spherical in shape with an average size of 15 nm in diameter by scanning electron microscopy and transmission electron microscopy. Energy-dispersive X-ray analysis clearly displayed the presence of gold particles. The structural analysis results with face central cubic crystalline nature and elemental composition, including gold, were confirmed by X-ray diffraction and X-ray photoelectron spectroscopy, respectively. In addition, Fourier transform infrared results identified the functional group in P. grandiflorum that is involved in the reduction of metal ions to gold nanoparticles. The synthesized P. grandiflorum gold nanoparticles exhibited efficient antibacterial activity against Escherichia coli (16 mm) and Bacillus subtilis (11 mm). This report confirms the synthesis of gold nanoparticle from balloon flower plant extracts, which can be used as a reducing and stabilizing agent and demonstrates its antibacterial applications.

Novel Nanoarchitechtonics Olive-Like Pd/BiVO4 for the Degradation of Gaseous Formaldehyde Under Visible Light Irradiation

2020 ◽  
Vol 20 (5) ◽  
pp. 2689-2697 ◽  
Author(s):  
Zhen Zhu ◽  
Wei-Gang Hong ◽  
Chin-Yuan Chen ◽  
Ren-Jang Wu
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
Irradiation Time ◽  
Light Irradiation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Formaldehyde Degradation ◽  
Gaseous Formaldehyde

In this research, olive-like Pd/BiVO4 was successfully prepared through a facile hydrothermal coreduction method for the photocatalytic degradation of formaldehyde under visible light irradiation. The structure, composition, and optical properties of the as-prepared Pd/BiVO4 were characterized through X-ray diffraction, transmission electron microscopy, ultraviolet-visible spectrophotometry, X-ray photoelectron spectroscopy, and photoluminescence. In addition, the photocatalytic activities of Pd/BiVO4 were evaluated through the photodegradation of formaldehyde. The experimental results demonstrated that the degradation efficiency of formaldehyde increased with increasing irradiation time. Moreover, 1.0 wt% Pd/BiVO4 exhibited the highest photocatalytic performance for formaldehyde degradation in 180 min, with the formaldehyde degradation rate as high as 87.5%.

scholarly journals A study of electrocatalytic ethanol oxidation of nanoporous PtSi alloy

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Nali Lu ◽  
Yao Li ◽  
Lei Zhang ◽  
Yong Fang ◽  
Bin Qian ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Three Dimensional ◽  
Oxidation Reactions ◽  
X Ray Diffraction ◽  
Direct Ethanol Fuel Cells ◽  
X Ray ◽  
Transmission Electron ◽  
Bicontinuous Structure ◽  
Average Size ◽  
Catalyzed Oxidation

In recent years, nanoporous alloys have presented the advantages of a large specific surface area, low density, and simple operation, and they have been widely used in the fields of catalysis, magnetism, and medicine. Nanoporous Pt-Si alloy was prepared by melt-spun and chemical dealloying, and was characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscope, and transmission electron microscopy. Pt-Si alloys possess a three-dimensional bicontinuous structure and an average size of 5 nanometers. Compared with commercial Pt/C catalysts, nanoporous Pt-Si alloys exhibit excellent electrocatalytic activity and stability in ethanol-catalyzed oxidation reactions. It is taken into consideration to be a promising catalyst in direct ethanol fuel cells.

scholarly journals α-Cellulose Fibers of Paper-Waste Origin Surface-Modified with Fe3O4 and Thiolated-Chitosan for Efficacious Immobilization of Laccase

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 581
Author(s):  
Gajanan S. Ghodake ◽  
Surendra K. Shinde ◽  
Ganesh D. Saratale ◽  
Rijuta G. Saratale ◽  
Min Kim ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Photoelectron Spectroscopy ◽  
Cellulose Fibers ◽  
Relative Activity ◽  
Significant Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Laccase Immobilization ◽  
Surface Modified

The utilization of waste-paper-biomass for extraction of important α-cellulose biopolymer, and modification of extracted α-cellulose for application in enzyme immobilization can be extremely vital for green circular bio-economy. Thus, in this study, α-cellulose fibers were super-magnetized (Fe3O4), grafted with chitosan (CTNs), and thiol (-SH) modified for laccase immobilization. The developed material was characterized by high-resolution transmission electron microscopy (HR-TEM), HR-TEM energy dispersive X-ray spectroscopy (HR-TEM-EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses. Laccase immobilized on α-Cellulose-Fe3O4-CTNs (α-Cellulose-Fe3O4-CTNs-Laccase) gave significant activity recovery (99.16%) and laccase loading potential (169.36 mg/g). The α-Cellulose-Fe3O4-CTNs-Laccase displayed excellent stabilities for temperature, pH, and storage time. The α-Cellulose-Fe3O4-CTNs-Laccase applied in repeated cycles shown remarkable consistency of activity retention for 10 cycles. After the 10th cycle, α-Cellulose-Fe3O4-CTNs possessed 80.65% relative activity. Furthermore, α-Cellulose-Fe3O4-CTNs-Laccase shown excellent degradation of pharmaceutical contaminant sulfamethoxazole (SMX). The SMX degradation by α-Cellulose-Fe3O4-CTNs-Laccase was found optimum at incubation time (20 h), pH (3), temperatures (30 °C), and shaking conditions (200 rpm). Finally, α-Cellulose-Fe3O4-CTNs-Laccase gave repeated degradation of SMX. Thus, this study presents a novel, waste-derived, highly capable, and super-magnetic nanocomposite for enzyme immobilization applications.

scholarly journals Surface Stoichiometry and Depth Profile of Tix-CuyNz Thin Films Deposited by Magnetron Sputtering

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3191
Author(s):  
Arun Kumar Mukhopadhyay ◽  
Avishek Roy ◽  
Gourab Bhattacharjee ◽  
Sadhan Chandra Das ◽  
Abhijit Majumdar ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Film Surface ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
Relative Composition ◽  
Transmission Electron ◽  
Deposited Film ◽  
Deposited Films

We report the surface stoichiometry of Tix-CuyNz thin film as a function of film depth. Films are deposited by high power impulse (HiPIMS) and DC magnetron sputtering (DCMS). The composition of Ti, Cu, and N in the deposited film is investigated by X-ray photoelectron spectroscopy (XPS). At a larger depth, the relative composition of Cu and Ti in the film is increased compared to the surface. The amount of adventitious carbon which is present on the film surface strongly decreases with film depth. Deposited films also contain a significant amount of oxygen whose origin is not fully clear. Grazing incidence X-ray diffraction (GIXD) shows a Cu3N phase on the surface, while transmission electron microscopy (TEM) indicates a polycrystalline structure and the presence of a Ti3CuN phase.

scholarly journals An Insight into Chemistry and Structure of Colloidal 2D-WS2 Nanoflakes: Combined XPS and XRD Study

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1969
Author(s):  
Riccardo Scarfiello ◽  
Elisabetta Mazzotta ◽  
Davide Altamura ◽  
Concetta Nobile ◽  
Rosanna Mastria ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Xrd Analysis ◽  
Crystal Habit ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Evaluation ◽  
Rational Understanding ◽  
Structural Inspection

The surface and structural characterization techniques of three atom-thick bi-dimensional 2D-WS2 colloidal nanocrystals cross the limit of bulk investigation, offering the possibility of simultaneous phase identification, structural-to-morphological evaluation, and surface chemical description. In the present study, we report a rational understanding based on X-ray photoelectron spectroscopy (XPS) and structural inspection of two kinds of dimensionally controllable 2D-WS2 colloidal nanoflakes (NFLs) generated with a surfactant assisted non-hydrolytic route. The qualitative and quantitative determination of 1T’ and 2H phases based on W 4f XPS signal components, together with the presence of two kinds of sulfur ions, S22− and S2−, based on S 2p signal and related to the formation of WS2 and WOxSy in a mixed oxygen-sulfur environment, are carefully reported and discussed for both nanocrystals breeds. The XPS results are used as an input for detailed X-ray Diffraction (XRD) analysis allowing for a clear discrimination of NFLs crystal habit, and an estimation of the exact number of atomic monolayers composing the 2D-WS2 nanocrystalline samples.

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

scholarly journals Aluminum Nitride-Silicon Carbide Alloy Crystals Grown on SiC Substrates by Sublimation

2005 ◽  
Vol 10 ◽  
Author(s):  
Z. Gu ◽  
L. Du ◽  
J.H. Edgar ◽  
E.A. Payzant ◽  
L. Walker ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
X Ray Diffraction ◽  
Original Source ◽  
X Ray ◽  
Alloy Crystal ◽  
Transmission Electron ◽  
Crystal Substrate ◽  
Vapor Distribution ◽  
Uniform Composition

AlN-SiC alloy crystals, with a thickness greater than 500 µm, were grown on 4H- and 6H-SiC substrates from a mixture of AlN and SiC powders by the sublimation-recondensation method at 1860-1990 °C. On-axis SiC substrates produced a rough surface covered with hexagonal grains, while 6H- and 4H- off-axis SiC substrates with different miscut angles (8° or 3.68°) formed a relatively smooth surface with terraces and steps. The substrate misorientation ensured that the AlN-SiC alloy crystals grew two dimensionally as identified by scanning electron microscopy (SEM). X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed that the AlN-SiC alloys had the wurtzite structure. Electron probe microanalysis (EPMA) and x-ray photoelectron spectroscopy (XPS) demonstrated that the resultant alloy crystals had non-stoichiometric ratios of Al:N and Si:C and a uniform composition throughout the alloy crystal from the interface to the surface. The composition ratio of Al:Si of the alloy crystals changed with the growth temperature, and differed from the original source composition, which was consistent with the results predicted by thermodynamic calculation of the solid-vapor distribution of each element. XPS detected the bonding between Si-C, Si-N, Si-O for the Si 2p spectra. The dislocation density decreased with the growth, which was lower than 106 cm−2 at the alloy surface, more than two orders of magnitude lower compared to regions close to the crystal/substrate interface, as determined by TEM.

Sign in / Sign up

Export Citation Format

Share Document