Formation and Characteristics of Thin Films of ZrO2-8 mol % Y2O3 Solid Electrolytes

2004 ◽  
Vol 97-98 ◽  
pp. 153-158 ◽  
Author(s):  
Darius Milčius ◽  
L.L. Pranevičius ◽  
V. Širvinskaitė ◽  
T. Šalkus ◽  
A. Kežionis ◽  
...  
Keyword(s):  
Thin Films ◽  
Solid Electrolytes ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
Cubic Symmetry ◽  
X Ray ◽  
Pulsed Dc ◽  
Pulsed Dc Magnetron Sputtering ◽  
Diffraction Patterns

Thin films of ZrO2-8mol%Y2O3 have been deposed by pulsed DC magnetron sputtering method. The substrates of Ni-cermet and alloy-600 for the films were used. The results of the investigation of the X-ray diffraction patterns and SEM showed that the films are nanocrystalline and belong to cubic symmetry. The relaxation process is related to the ion transport in thin films. The results of the investigation of the temperature dependencies of thin films ionic conductivity (σ) showed that the dependence σ(T) is caused by the temperature dependence of oxygen vacancy mobility, while the number of charge carriers remains constant with temperature.

Preparation of Thin Cu Electrode on Al2O3 + Clay Substrate by Pulsed DC Magnetron Sputtering

2013 ◽  
Vol 770 ◽  
pp. 335-338
Author(s):  
Nuansiri Chansimuang ◽  
Tosawat Seetawan
Keyword(s):  
Magnetron Sputtering ◽  
Thermoelectric Module ◽  
Mean Value ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
X Ray ◽  
Hardness Tester ◽  
Pulsed Dc ◽  
Pulsed Dc Magnetron Sputtering ◽  
Diffraction Patterns

Aluminum oxide (Al2O3) and Copper (Cu) are popular into insulator and electrode for thermoelectric module. The Al2O3 + clay substrate was prepared by solid state reaction and the thin Cu electrode prepared by pulsed DC magnetron sputtering. Crystal structure and microstructure of the substrate were measured by using the X-ray diffraction and scanning electron microscopy techniques. The Vicker hardness and density were measured by Micro Hardness tester and Archimedes method, respectively. The X-ray diffraction patterns of the substrate were obtained mix phases such as Al2O3, clay and Cu phases. The hardness and density were obtained mean value of 332.11 HV and 2.47 g/cm3.

Characterization of Ti–Zr–V thin films deposited by DC and unipolar pulsed DC magnetron sputtering

Vacuum ◽  
2021 ◽  
Vol 188 ◽  
pp. 110200
Author(s):  
Sihui Wang ◽  
Wei Wei ◽  
Yonghao Gao ◽  
Haibin Pan ◽  
Yong Wang
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Dc Magnetron Sputtering ◽  
Pulsed Dc ◽  
Pulsed Dc Magnetron Sputtering

Determining the C60 molecular arrangement in thin films by means of X-ray diffraction

2011 ◽  
Vol 44 (5) ◽  
pp. 983-990 ◽  
Author(s):  
Chris Elschner ◽  
Alexandr A. Levin ◽  
Lutz Wilde ◽  
Jörg Grenzer ◽  
Christian Schroer ◽  
...  
Keyword(s):  
Thin Films ◽  
Structural Information ◽  
Grazing Incidence ◽  
Test Material ◽  
C60 Fullerene ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molecular Arrangement ◽  
Diffraction Patterns

The electrical and optical properties of molecular thin films are widely used, for instance in organic electronics, and depend strongly on the molecular arrangement of the organic layers. It is shown here how atomic structural information can be obtained from molecular films without further knowledge of the single-crystal structure. C60 fullerene was chosen as a representative test material. A 250 nm C60 film was investigated by grazing-incidence X-ray diffraction and the data compared with a Bragg–Brentano X-ray diffraction measurement of the corresponding C60 powder. The diffraction patterns of both powder and film were used to calculate the pair distribution function (PDF), which allowed an investigation of the short-range order of the structures. With the help of the PDF, a structure model for the C60 molecular arrangement was determined for both C60 powder and thin film. The results agree very well with a classical whole-pattern fitting approach for the C60 diffraction patterns.

ITO Thin Films on Silicon Buffer by Sol Gel Method

2006 ◽  
Vol 514-516 ◽  
pp. 1155-1160 ◽  
Author(s):  
Talaat Moussa Hammad
Keyword(s):  
Thin Films ◽  
Indium Tin Oxide ◽  
Optical Transmission ◽  
Sol Gel ◽  
Precursor Solution ◽  
Charge Carriers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ito Thin Films ◽  
Uv Visible

Sol gel indium tin oxide thin films (In: Sn = 90:10) were prepared by the sol-gel dipcoating process on silicon buffer substrate. The precursor solution was prepared by mixing SnCl2.2H2O and InCl3 dissolved in ethanol and acetic acid. The crystalline structure and grain orientation of ITO films were determined by X-ray diffraction. The surface morphology of the films was characterized by scanning electron microscope (SEM). Optical transmission and reflectance spectra of the films were analyzed by using a UV-visible spectrophotometer. The transport properties of majority charge carriers for these films were studied by Hall measurement. ITO thin film with electrical resistivity of 7.6 ×10-3 3.cm, Hall mobility of approximately 2 cm2(Vs)-1 and free carrier concentration of approximately 4.2 ×1020 cm-3 are obtained for films 100 nm thick films. The I-V curve measurement showed typical I-V characteristic behavior of sol gel ITO thin films.

Transparent Conductive Cu-In-O Thin Films Deposited by Reactive DC Magnetron Sputtering with Different Targets

2011 ◽  
Vol 239-242 ◽  
pp. 2752-2755
Author(s):  
Fan Ye ◽  
Xing Min Cai ◽  
Fu Ping Dai ◽  
Dong Ping Zhang ◽  
Ping Fan ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Optical Band Gap ◽  
Diffraction Peak ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
Flow Rates ◽  
X Ray ◽  
Equal Distance ◽  
Transmittance Curve

Transparent conductive Cu-In-O thin films were deposited by reactive DC magnetron sputtering. Two types of targets were used. The first was In target covered with a fan-shaped Cu plate of the same radius and the second was Cu target on which six In grains of 1.5mm was placed with equal distance between each other. The samples were characterized with scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), UV/VIS spectrophotometer, four-probe measurement etc. SEM shows that the surfaces of all the samples are very smooth. EDX shows that the samples contain Cu, In as well as O, and different targets result in different atomic ratios of Cu to In. A diffraction peak related to rhombohedra-centered In2O3(012) is observed in the XRD spectra of all the samples. For both the two targets, the transmittance decreases with the increase of O2flow rates. The direct optical band gap of all the samples is also estimated according to the transmittance curve. For both the two targets, different O2flow rates result in different sheet resistances and conductivities. The target of Cu on In shows more controllability in the composition and properties of Cu-In-O films.

scholarly journals Effect of indium content on X- ray diffraction and optical constants of InxSe1-x thin films

2019 ◽  
Vol 14 (29) ◽  
pp. 55-72
Author(s):  
Bushra A. Hasan
Keyword(s):  
Thin Films ◽  
Optical Constants ◽  
Indium Content ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Dispersion Energy ◽  
X Ray ◽  
Evaporation Technique ◽  
High Indium Content ◽  
Diffraction Patterns

Alloys of InxSe1-x were prepared by quenching technique withdifferent In content (x=10, 20, 30, and 40). Thin films of these alloyswere prepared using thermal evaporation technique under vacuum of10-5 mbar on glass, at room temperature R.T with differentthicknesses (t=300, 500 and 700 nm). The X–ray diffractionmeasurement for bulk InxSe1-x showed that all alloys havepolycrystalline structures and the peaks for x=10 identical with Se,while for x=20, 30 and 40 were identical with the Se and InSestandard peaks. The diffraction patterns of InxSe1-x thin film showthat with low In content (x=10, and 20) samples have semicrystalline structure, The increase of indium content to x=30decreases degree of crystallinity and further increase of indiumcontent to x=40 leads to convert structure to amorphous. Increase ofthickness from 300 to 700nm increases degree of crystallinity for allindium content. Transmittance measurements were used to calculaterefractive index n and the extinction coefficient k using Swanepole’smethod. The optical constants such as refractive index (n), extinctioncoefficient (k) and dielectric constant (εr, εi) increases for low indiumcontent samples and decreases for high indium content samples,while increase of thickness increases optical constants for all xvalues. The oscillator energy E0, dispersion energy Ed, and otherparameters have been determined by Wemple - DiDomenico singleoscillator approach.

The Use of BaF2 Buffer Layers for the Sputter-Deposition of Ticabacuo Thin-Film Superconductors

1989 ◽  
Vol 169 ◽  
Author(s):  
K.M. Hubbard ◽  
P.N. Arendt ◽  
D.R. Brown ◽  
D.W. Cooke ◽  
N.E. Elliott ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Sputter Deposition ◽  
Buffer Layers ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
X Ray ◽  
Film Substrate ◽  
Ion Backscattering ◽  
Scanning Electron

AbstractThin films of the Tl‐based superconductors often have relatively poor properties because of film/substrate interdiffusion which occurs during the anneal. We have therefore investigated the use of BaF2 as a diffusion barrier. TICaBaCuO thin films were deposited by dc magnetron sputtering onto MgO <100> substrates, both with and without an evaporation‐deposited BaF2 buffer layer, and post‐annealed in a Tl over‐pressure. Electrical properties of the films were determined by four‐point probe analysis, and compositions were measured by ion‐backscattering spectroscopy. Structural analysis was performed by X‐ray diffraction and scanning electron microscopy. The BaF2 buffer layers were found to significantly improve the properties of the TICaBaCuO thin films.

Sign in / Sign up

Export Citation Format

Share Document