Achieving Tier 2 Bin 5 Emission Levels with a Medium Duty Diesel Pick-Up and a NOX Adsorber, Diesel Particulate Filter Emissions System-Exhaust Gas Temperature Management

2004 ◽  
Author(s):  
Cynthia C. Webb ◽  
Phillip A. Weber ◽  
Matthew Thornton
Keyword(s):  
Diesel Particulate Filter ◽  
Particulate Filter ◽  
Temperature Management ◽  
Exhaust Gas ◽  
Tier 2 ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Nox Adsorber ◽  
Exhaust Gas Temperature

Cylinder Pressure Information-Based Postinjection Timing Control for Aftertreatment System Regeneration in a Diesel Engine—Part II: Active Diesel Particulate Filter Regeneration

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Hyunjun Lee ◽  
Jaesik Shin ◽  
Manbae Han ◽  
Myoungho Sunwoo
Keyword(s):  
Diesel Particulate Filter ◽  
Fuel Injection ◽  
Control Method ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

The successful utilization of a diesel particulate filter (DPF) to reduce particulate matter (PM) in a passenger car diesel engine necessitates a periodic regeneration of the DPF catalyst without deterioration of the drivability and emission control performance. For successful active DPF regeneration, the exhaust gas temperature should be over 500 °C to oxidize the soot loaded in the DPF. Previous research increased the exhaust gas temperature by applying early and late post fuel injection with a look-up table (LUT) based feedforward control implemented into the engine management system (EMS). However, this method requires enormous calibration work to find the optimal timing and quantity of the main, early, and late post fuel injection with less certainty of accurate torque control. To address this issue, we propose a cylinder pressure based multiple fuel injection (MFI) control method for active DPF regeneration. The feedback control of the indicated mean effective pressure (IMEP), lambda, and DPF upstream temperature was applied to precisely control the injection quantity of the main, early, and late post fuel injection. To determine their fuel injection timings, a mass fraction burned 60% after location of the rate of heat release maximum (MFB60aLoROHRmax) was proposed based on the cylinder pressure information. The proposed control method was implemented in an in-house EMS and validated at several engine operating conditions. During the regeneration period, the exhaust gas temperature tracked the desired temperature, and the engine torque fluctuation was minimized with minimal PM and NOx emissions.

Effect of the Fuel Injection Strategy on Diesel Particulate Filter Regeneration in a Single-Cylinder Diesel Engine

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) have forced automotive manufacturers to equip a diesel particulate filter (DPF) on diesel cars. Generally, postinjection is used as a method to regenerate the DPF. However, it is known that postinjection deteriorates the specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration is one of the key technologies for diesel powertrains equipped with a DPF. This paper presents correlations between the fuel injection strategy and exhaust gas temperature for DPF regeneration. The experimental apparatus consists of a single-cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, the postinjection timing was in the range of 40 deg aTDC to 110 deg aTDC and double postinjection was considered. In addition, the effects of the injection pressure were investigated. The engine load was varied among low load to midload conditions, and the amount of fuel of postinjection was increased up to 10 mg/stk. The oil dilution during the fuel injection and combustion processes was estimated by the diesel loss measured by comparing two global equivalences ratios: one measured from a lambda sensor installed at the exhaust port and one estimated from the intake air mass and injected fuel mass. In the present study, the differences of the global equivalence ratios were mainly caused by the oil dilution during postinjection. The experimental results of the present study suggest optimal engine operating conditions including the fuel injection strategy to obtain an appropriate exhaust gas temperature for DPF regeneration. The experimental results of the exhaust gas temperature distributions for various engine operating conditions are discussed. In addition, it was revealed that the amount of oil dilution was reduced by splitting the postinjection (i.e., double postinjection). The effects of the injection pressure on the exhaust gas temperature were dependent on the combustion phasing and injection strategies.

scholarly journals Nanostructure changes in diesel soot during NO2–O2 oxidation under diesel particulate filter-like conditions toward filter regeneration

2018 ◽  
Vol 20 (8-9) ◽  
pp. 953-966 ◽  
Author(s):  
Madhu Singh ◽  
Mek Srilomsak ◽  
Yujun Wang ◽  
Katsunori Hanamura ◽  
Randy Vander Wal
Keyword(s):  
Diesel Particulate Filter ◽  
Surface Oxidation ◽  
Soot Oxidation ◽  
Diesel Soot ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Fringe Analysis ◽  
Diesel Particulate ◽  
Oxidation Rates ◽  
Passive Regeneration

Development of the regeneration process on diesel particulate filters requires a better understanding of soot oxidation phenomena, especially its relation to soot nanostructure. Nitrogen dioxide (NO2) is known to play an essential role in passive regeneration by oxidizing soot at low temperatures, especially in the presence of oxygen (O2) in the exhaust. However, change in soot nanostructure due to oxidation by NO2–O2 mixtures has not received much attention. This work focuses on nanostructure evolution during passive regeneration of the diesel particulate filter by oxidation of soot at normal exhaust gas temperatures (300°C–400°C). High-resolution transmission electron microscopy of partially oxidized model carbons (R250, M1300, arc-generated soot) and diesel soot under NO2–O2 mixtures is used to investigate physical changes in nanostructure correlating with the material’s behavior during oxidation. Microscopy reveals the changing nanostructure of model carbons during oxidation while fringe analysis of the images points to the differences in the structural metrics of fringe length and tortuosity of the resultant structures. The variation in oxidation rates highlights the inter-dependence of the material’s reactivity with its structure. NO2 preferentially oxidizes edge-site carbon, promotes surface oxidation by altering the particle’s burning mode with increased overall reactivity of NO2+O2 resulting in inhibition of internal burning, typically observed by O2 at exhaust gas temperatures.

scholarly journals Late Fuel Post-Injection Influence on the Dynamics and Efficiency of Wall-Flow Particulate Filters Regeneration

2019 ◽  
Vol 9 (24) ◽  
pp. 5384 ◽  
Author(s):  
José Ramón Serrano ◽  
Pedro Piqueras ◽  
Joaquín de la Morena ◽  
Enrique José Sanchis
Keyword(s):  
Fuel Consumption ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Particulate Filters ◽  
Exhaust Temperature ◽  
Injection Parameters ◽  
Wall Flow

Late fuel post-injections are the most usual strategy to reach high exhaust temperature for the active regeneration of diesel particulate filters. However, it is important to optimise these strategies in order to mitigate their negative effect on the engine fuel consumption. This work aims at understanding the influence of the post-injection parameters, such as its start of injection and its fuel quantity, on the duration of the regeneration event and the fuel consumption along it. For this purpose, a set of computational models are employed to figure out in a holistic way the involved phenomena in the interaction between the engine and the exhaust gas aftertreatment system. Firstly, an engine model is implemented to evaluate the effect of the late fuel post-injection pattern on the gas properties at the exhaust aftertreatment system inlet in different steady-state operating conditions. These are selected to provide representative boundary conditions of the exhaust gas flow concerning dwell time, exhaust temperature and O 2 concentration. In this way, the results are later applied to the analysis of the diesel oxidation catalyst and wall-flow particulate filter responses. The dependence of the diesel particulate filter (DPF) inlet temperature is discussed based on the efficiency of each post-injection strategy to increase the exhaust gas temperature. Next, the influence on the dynamics of the regeneration of the post-injection parameters through the change in gas temperature and O 2 concentration is finally studied distinguishing the pre-heating, maximum reactivity and late soot oxidation stages as well as the required fuel consumption to complete the regeneration process.

Experimental Analysis of Sudden Pressure Increase Phenomenon by Real-Time Internal Observation of Diesel Particulate Filter

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Rui Fukui ◽  
Yuki Okamoto ◽  
Masayuki Nakao
Keyword(s):  
Particulate Matter ◽  
Pressure Drop ◽  
Diesel Particulate Filter ◽  
Operating Conditions ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Visualization Method ◽  
Diesel Particulate ◽  
Wide Perspective ◽  
Deposit Layer

As a way of reducing the amount of particulate matter (PM) contained in the exhaust gas, diesel particulate filter (DPF) is widely used. To keep the condition of DPF normal and effective, estimation of the amount of PM deposits in the DPF is important. The estimation is mainly conducted based on the value of pressure drop across the DPF. Occasionally, the value of the pressure drop rises suddenly and it leads to overestimation of the amount of PM deposits. In order to elucidate the cause of the sudden pressure drop increase phenomenon, this paper first reveals the engine operating conditions which invoke this phenomenon. The authors also have developed a visualization method to realize the wide-perspective internal observation of the DPF. The observation experiment has been conducted with a commercial engine and DPF under the revealed conditions. Experimental results make clear that the phenomenon is caused by PM deposit layer collapse and channel plugging.

Sign in / Sign up

Export Citation Format

Share Document