D.I. Diesel Engine In-Cylinder Pressure Data Analysis Under T.D.C. Setting Error

1993 ◽  
Author(s):  
V. Rocco
Keyword(s):  
Data Analysis ◽  
Diesel Engine ◽  
Cylinder Pressure ◽  
Pressure Data ◽  
Setting Error

Preliminary Energy-Efficiency Analysis on Multi-Pulse Injection Schedule in a Diesel Engine

2005 ◽  
Author(s):  
Raj Kumar ◽  
Ming Zheng ◽  
Graham T. Reader
Keyword(s):  
Energy Efficiency ◽  
Diesel Engine ◽  
Heat Release ◽  
Fuel Injection ◽  
Efficiency Analysis ◽  
Simulation Software ◽  
Cylinder Pressure ◽  
Pressure Data ◽  
Exhaust Temperature ◽  
Energy Efficiency Analysis

The multi-pulse fuel injection in a diesel engine is considered an effective way to reduce nitrogen oxides (NOx) emissions by heat-release shaping. In this research a preliminary energy efficiency analysis has been conducted for various split injection rates and schedules using the in-house and the commercial engine simulation software. Theoretical findings have been validated using experimentally obtained cylinder pressure data for various injection timings from a single-cylinder engine. The theoretical analysis on the shape of heat- release has been made to evaluate the energy efficiency of the post injection pulses on the engine exhaust temperature increases. An investigation of the cycle-to-cycle variation has also been performed for the measured cylinder pressure data.

Real-Time IMEP Estimation and Control Using an In-Cylinder Pressure Sensor for a Common-Rail Direct Injection Diesel Engine

2011 ◽  
Vol 133 (6) ◽  
Author(s):  
Seungsuk Oh ◽  
Junsoo Kim ◽  
Byounggul Oh ◽  
Kangyoon Lee ◽  
Myoungho Sunwoo
Keyword(s):  
Diesel Engine ◽  
Real Time ◽  
Direct Injection ◽  
Common Rail ◽  
Cylinder Pressure ◽  
Pressure Data ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Estimation And Control ◽  
And Control

An in-cylinder pressure-based control method is capable of improving engine performance, as well as reducing harmful emissions. However, this method is difficult to be implemented in a conventional engine management system due to the excessive data acquisition and long computation time. In this study, we propose a real-time indicated mean effective pressure (IMEP) estimation method using cylinder pressure in a common-rail direct injection diesel engine. In this method, difference pressure integral (DPI) was applied to the estimation. The DPI requires only 180 pressure data points during one engine cycle from top dead center to bottom dead center when pressure data are captured at every crank angle. Therefore, the IMEP can be estimated in real time. To further reduce the computational load, the IMEP was also estimated using DPI at 2 deg, 3 deg, and 4 deg crank angle resolutions. Furthermore, based on the estimated IMEP, we controlled IMEP using a radial basis function network and linear feedback controller. As a result of the study, successful estimation and control were demonstrated through engine experiments.

Modeling and validation of crankshaft speed fluctuations of a single-cylinder four-stroke diesel engine

2021 ◽  
pp. 095440702110262
Author(s):  
Mustafa Babagiray ◽  
Hamit Solmaz ◽  
Duygu İpci ◽  
Fatih Aksoy
Keyword(s):  
Diesel Engine ◽  
Dynamic Model ◽  
Moment Of Inertia ◽  
Mass Motion ◽  
Cylinder Pressure ◽  
Motion Equations ◽  
Single Cylinder ◽  
Mass Moment ◽  
Mass Moment Of Inertia ◽  
Speed Fluctuations

In this study, a dynamic model of a single-cylinder four-stroke diesel engine has been created, and the crankshaft speed fluctuations have been simulated and validated. The dynamic model of the engine consists of the motion equations of the piston, conrod, and crankshaft. Conrod motion was modeled by two translational and one angular motion equations, by considering the kinetic energy resulted from the mass moment of inertia and conrod mass. Motion equations involve in-cylinder gas pressure forces, hydrodynamic and dry friction, mass inertia moments of moving parts, starter moment, and external load moment. The In-cylinder pressure profile used in the model was obtained experimentally to increase the accuracy of the model. Pressure profiles were expressed mathematically using the Fourier series. The motion equations were solved by using the Taylor series method. The solution of the mathematical model was performed by coding in the MATLAB interface. Cyclic speed fluctuations obtained from the model were compared with experimental results and found compitable. A validated model was used to analyze the effects of in-cylinder pressure, mass moment of inertia of crankshaft and connecting rod, friction, and piston mass. In experiments for 1500, 1800, 2400, and 2700 rpm engine speeds, crankshaft speed fluctuations were observed as 12.84%, 8.04%, 5.02%, and 4.44%, respectively. In simulations performed for the same speeds, crankshaft speed fluctuations were calculated as 10.45%, 7.56%, 4.49%, and 3.65%. Besides, it was observed that the speed fluctuations decreased as the average crankshaft speed value increased. In the simulation for 157.07, 188.49, 219.91, 251.32, and 282.74 rad/s crankshaft speeds, crankshaft speed fluctuations occurred at rates of 10.45%, 7.56%, 5.84%, 4.49%, and 3.65%, respectively. The effective engine power was achieved as 5.25 kW at an average crankshaft angular speed of 219.91 rad/s. The power of friction loss in the engine was determined as 0.68 kW.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Numerical and Experimental Study on the Impact of Mild Cold EGR on Exhaust Emissions in a Biodiesel Fueled Diesel Engine

2021 ◽  
Author(s):  
Alex Oliveira ◽  
Junfeng Yang ◽  
Jose Sodre
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Exhaust Emissions ◽  
Pollutant Emissions ◽  
Cylinder Pressure ◽  
Nox Formation ◽  
Ratio Distribution ◽  
Engine Model ◽  
Gas Recirculation ◽  
The Impact

Abstract This work evaluated the effect of cooled exhaust gas recirculation (EGR) on fuel consumption and pollutant emissions from a diesel engine fueled with B8 (a blend of biodiesel and Diesel 8:92%% by volume), experimentally and numerically. Experiments were carried out on a Diesel power generator with varying loads from 5 kW to 35 kW and 10% of cold EGR ratio. Exhaust emissions (e.g. THC, NOX, CO etc.) were measured and evaluated. The results showed mild EGR and low biodiesel content have minor impact of engine specific fuel consumption, fuel conversion efficiency and in-cylinder pressure. Meanwhile, the combination of EGR and biodiesel reduced THC and NOX up to 52% and 59%, which shows promising effect on overcoming the PM-NOX trade-off from diesel engine. A 3D CFD engine model incorporated with detailed biodiesel combustion kinetics and NOx formation kinetics was validated against measured in-cylinder pressure, temperature and engine-out NO emission from diesel engine. This valid model was then employed to investigate the in-cylinder temperature and equivalence ratio distribution that predominate NOx formation. The results showed that the reduction of NOx emission by EGR and biodiesel is obtained by a little reduction of the local in-cylinder temperature and, mainly, by creating comparatively rich combusting mixture.

Sign in / Sign up

Export Citation Format

Share Document