scholarly journals Optimal Location of IPFC That Handles Operating Constraints for Reducing Transmission Lines Utilization Levels in Electric Power Grid

2021 ◽  
Vol 6 (2) ◽  
pp. 31-39
Author(s):  
S Adetona ◽  
M Iyayi ◽  
R Salawu
Keyword(s):  
Transmission Line ◽  
Transmission Lines ◽  
Energy Demand ◽  
Reactive Power ◽  
Power Grid ◽  
Electric Energy ◽  
Load Flow ◽  
Optimal Location ◽  
Test Bed ◽  
Operating Constraints

The day-to-day increase in electric energy demand with increasing population and urbanization is causing transmission facilities to transfer load at their upper limits; therefore, the probability of failures of these facilities increases. One of the ways of mitigating failures is by constructing more transmission lines; which would serve as alternatives to reduce the transmission line utilization levels (TLUL). However, there are constraints in adopting this method; therefore, the use of Interline Power Flow Controller (IPFC) has been suggested by many researchers; but very few of these studies proposed the IPFC that has capability of handling operating constraints (IPFCthC) in solving power transmission systems issues. Some of the studies that proposed the IPFCthC use trial and error approach in identifying the optimal location for its injection in multi-buses power grid. Also, some of the studies that proposed the IPFCthC do not employ it to investigate its capability in reducing TLUL. In order to reduce the TSUL in the multi-bus grid, this paper therefore proposes optimal location for the injection of IPFCthC using Transmission Line Performance Index (TLPI) and Transmission Line Reactive Power Loss (TLRPL) in Newton-Raphson Load Flow (NRLF) algorithm. The proposed algorithm was tested on IEEE-30 Test-bed in Matlab environment. The results obtained reveal that the TLUL of each of the transmission lines of the Test-bed that is not connected to PV bus is reduced averagely by 4.00 % each, with the injection of the IPFCthC in an optimally location established by the proposed algorithm.

scholarly journals Optimal location of unified power flow controller genetic algorithm based

2020 ◽  
Vol 11 (2) ◽  
pp. 886
Author(s):  
Sana Khalid Abdul Hassan ◽  
Firas Mohammed Tuaimah
Keyword(s):  
Genetic Algorithm ◽  
Power Generation ◽  
Power System ◽  
Transmission Line ◽  
Transmission Lines ◽  
Power Flow ◽  
Optimal Power Flow ◽  
Reactive Power ◽  
Optimal Location ◽  
Power Losses

<p>Now-a-days the Flexible AC Transmission Systems (FACTS) technology is very effective in improving the power flow along the transmission lines and makes the power system more flexible and controllable. This paper deals with overload transmission system problems such as (increase the total losses, raise the rate of power generation, and the transmission line may be exposed to shut down when the load demand increase from the thermal limit of transmission line) and how can solve this problem by choosing the optimal location and parameters of Unified Power Flow Controllers (UPFCs). which was specified based on Genetic Algorithm (GA) optimization method, it was utilized to search for optimum FACT parameters setting and location based to achieve the following objectives: improve voltages profile, reduce power losses, treatment of power flow in overloaded transmission lines and reduce power generation. MATLAB was used for running both the GA program and Newton Raphson method for solving the load flow of the system The proposed approach is examined and tested on IEEE 30-bus system. The practical part has been solved through Power System Simulation for Engineers (PSS\E) software Version 32.0 (The Power System Simulator for Engineering (PSS/E) software created from Siemens PTI to provide a system of computer programs and structured data files designed to handle the basic functions of power system performance simulation work, such as power flow, optimal power flow, fault analysis, dynamic simulations...etc.). The Comparative results between the experimental and practical parts obtained from adopting the UPFC where too close and almost the same under different loading conditions, which are (5%, 10%, 15% and 20%) of the total load. can show that the total active power losses for the system reduce at 69.594% at normal case after add the UPFC device to the system. also the reactive power losses reduce by 75.483% at the same case as well as for the rest of the cases. in the other hand can noted the system will not have any overload lines after add UPFC to the system with suitable parameters.</p>

scholarly journals Optimization for Electric Power Load Forecast

2018 ◽  
Vol 8 (5) ◽  
pp. 3453 ◽  
Author(s):  
I. A. Ethmane ◽  
M. Maaroufi ◽  
A. K. Mahmoud ◽  
A. Yahfdhou
Keyword(s):  
Transmission Lines ◽  
Energy Demand ◽  
Power Flow ◽  
Power Plants ◽  
Reactive Power ◽  
Load Flow ◽  
Voltage Profile ◽  
Demand Forecast ◽  
Reactive Power Flow ◽  
Power Load

Load flow studies are one of the most important aspects of power system planning and operation. The main information obtained from this study comprises the magnitudes and phase angles of load bus voltages, reactive powers at generators buses, real and reactive power flow on transmission lines, other variables being known. To solve the problem of load flow, we use the iterative method, of Newton-Raphson. Analysis of the found results using numerical method programmed on the Matlab software and PSS/E Simulator lead us to seek means of controlling the reactive powers and the bus voltages of the Nouakchott power grid in 2030 year. In our case, we projected the demand forecast at 2015 to 2030 years. To solve the growing demand we injected the power plants in the system firstly and secondly when the production and energy demand are difficult to match due to lack of energy infrastructures in 2030.It is proposed to install a FACTS (Flexible Alternative Current Transmission Systems) system at these buses to compensate or provide reactive power in order to maintain a better voltage profile and transmit more power to customers.

Performance Analysis on Transmission Line for Improvement of Load Flow

2012 ◽  
Vol 433-440 ◽  
pp. 7208-7212
Author(s):  
Ya Min Su Hlaing ◽  
Ze Ya Aung
Keyword(s):  
Steady State ◽  
Power System ◽  
Transmission Line ◽  
Power Flow ◽  
Reactive Power ◽  
Load Flow ◽  
Electric Power System ◽  
Steady State Condition ◽  
Newton Raphson ◽  
Raphson Method

This thesis implements power flow application, Newton-Raphson method. The Newton-Raphson method is mainly employed in the solution of power flow problems. The network of Myanma electric power system is used as the reference case. The system network contains 90 buses and 106 brunches. The weak points are found in the network by using Newton-Raphson method. Bus 16, 17, 85 and 86 have the most weak bus voltages. The medium transmission line between bus 87 and bus 17 is compensated by using MATLAB program software. The transmission line is compensated with shunt reactors, series and shunt capacitors to improve transient and steady-state stability, more economical loading, and minimum voltage dip on load buses and to supply the requisite reactive power to maintain the receiving end voltage at a satisfactory level. The system performance is tested under steady-state condition. This paper investigates and improves the steady–state operation of Myanma Power System Network.

Transmission Line

2020 ◽  
pp. 43-71
Keyword(s):  
Transmission Line ◽  
Transmission Lines ◽  
Magnetic Energy ◽  
Propagation Constant ◽  
Characteristic Impedance ◽  
Electric Energy ◽  
Electromagnetic Energy ◽  
The Other ◽  
Electrical Characteristics ◽  
Lumped Elements

A transmission line (TL) is simply a medium that is capable of guiding or propagating electromagnetic energy. The transmission line stores the electric (E) and magnetic (M) energies and distributes them in space by alternating them between the two forms. This means that at any point along a TL, energy is stored in a mixture of E and M forms and, for an alternating signal at any point on the TL, converted from one form to the other as time progresses. Transmission line is usually modelled using lumped elements (i.e., inductors for magnetic energy, capacitors for electric energy, and resistors for modelling losses). The electrical characteristics of a TL such as the propagation constant, the attenuation constant, the characteristic impedance, and the distributed circuit parameters can only be determined from the knowledge of the fields surrounding the transmission line. This chapter gives a brief overview of various transmission lines, with more detailed discussions on the microstrip and the SIW.

scholarly journals Study on icing and its trip laws of transmission lines in Shanxi Power Grid

2021 ◽  
Vol 252 ◽  
pp. 01055
Author(s):  
Bin Zhao ◽  
Li-chun Zhang ◽  
Jia-lun Yang ◽  
Kun-peng Ji
Keyword(s):  
Transmission Lines ◽  
Power Grid ◽  
Electric Energy ◽  
Energy Transmission ◽  
Safe Operation ◽  
Overhead Transmission Lines ◽  
Power Load ◽  
Capacity Improvement

Overhead transmission lines are important carriers of electric energy transmission. Their icing, galloping and shedding in winter and spring seriously threatened the safe operation of Shanxi power grid. Especially in the recent years, compact lines and double circuit lines on the same tower, typical types of overhead transmission lines in Shanxi Power Grid, were affected by frequent trips induced by icing, galloping, and shedding appeared in their conductors repeatedly, which seriously reduced the capacity of power energy transmission in Shanxi and caused trillions of power load losses. Through detailed investigation and analysis of the characteristics and historical fault cases of compact lines and double circuit lines on the same tower in Shanxi Power Grid, the key causes and main laws of two types of lines in Shanxi Power Grid are clarified, which could provide support for the follow-up line anti-ice technical transformation and capacity improvement.

scholarly journals Load Flow Analysis in Hybrid AC-DC Transmission Network

2021 ◽  
pp. 617-624
Author(s):  
Ajith M ◽  
Dr. R. Rajeswari
Keyword(s):  
Power Systems ◽  
Power System ◽  
Transmission Lines ◽  
Power Flow ◽  
Reactive Power ◽  
Short Circuit ◽  
Flow Analysis ◽  
Load Flow ◽  
System Stability ◽  
And Control

Power-flow studies are of great significance in planning and designing the future expansion of power systems as well as in determining the best operation of existing systems. Technologies such as renewables and power electronics are aiding in power conversion and control, thus making the power system massive, complex, and dynamic. HVDC is being preferred due to limitations in HVAC such as reactive power loss, stability, current carrying capacity, operation and control. The HVDC system is being used for bulk power transmission over long distances with minimum losses using overhead transmission lines or submarine cable crossings. Recent years have witnessed an unprecedented growth in the number of the HVDC projects. Due to the vast size and inaccessibility of transmission systems, real time testing can prove to be difficult. Thus analyzing power system stability through computer modeling and simulation proves to be a viable solution in this case. The motivation of this project is to construct and analyze the load flow and short circuit behavior in an IEEE 14 bus power system with DC link using MATLAB software. This involves determining the parameters for converter transformer, rectifier, inverter and DC cable for modelling the DC link. The line chosen for incorporation of DC link is a weak bus. This project gives the results of load flow and along with comparison of reactive power flow, system losses, voltage in an AC and an AC-DC system.

Investigation of the Normal Working Mode of the Nigerian 330-132 kV Network in View of Perspective Load Growth Forecast up to 10 years

2007 ◽  
Vol 18-19 ◽  
pp. 87-92
Author(s):  
A.O. Melodi
Keyword(s):  
Reactive Power ◽  
Power Grid ◽  
Maximum Load ◽  
Load Flow ◽  
Power Sources ◽  
Load Growth ◽  
Thermal Constraints ◽  
Transfer Capability ◽  
Exponential Trend ◽  
Analysis Of Results

In this paper the normal regimes of the Nigerian 330-132 kV power grid at 2003-2005 year levels were analyzed. The load flow studies were also carried out at perspective load growth forecast up to 10 years based on exponential trend using a program (Newton’s method). An analysis of results shows that with existing available generation and maximum load estimate by the utility there is a deficit which will persist if generation, commensurate with load growth, is not immediately reinforced. The network lacks adequate reactive power sources to maintain permissible bus voltages and the power transfer capability due to thermal constraints.

Optimal location of interline power flow controller in a power system network using ABC algorithm

2013 ◽  
Vol 62 (1) ◽  
pp. 91-110 ◽  
Author(s):  
S. Sreejith ◽  
Sishaj Psimon ◽  
M.P. Selvan
Keyword(s):  
Power System ◽  
Transmission Lines ◽  
Power Flow ◽  
Reactive Power ◽  
Optimal Location ◽  
Voltage Profile ◽  
Optimal Position ◽  
Flow Controller ◽  
Power Flow Controller ◽  
Installation Cost

Abstract This paper proposes a methodology based on installation cost for locating the optimal position of interline power flow controller (IPFC) in a power system network. Here both conventional and non conventional optimization tools such as LR and ABC are applied. This methodology is formulated mathematically based on installation cost of the FACTS device and active power generation cost. The capability of IPFC to control the real and reactive power simultaneously in multiple transmission lines is exploited here. Apart from locating the optimal position of IPFC, this algorithm is used to find the optimal dispatch of the generating units and the optimal value of IPFC parameters. IPFC is modeled using Power Injection (PI) model and incorporated into the problem formulation. This proposed method is compared with that of conventional LR method by validating on standard test systems like 5-bus, IEEE 30-bus and IEEE 118-bus systems. A detailed discussion on power flow and voltage profile improvement is carried out which reveals that incorporating IPFC into power system network in its optimal location significantly enhance the load margin as well as the reliability of the system.

Analysis on Capacity of Transmission Line Based on Thermal Rating

2014 ◽  
Vol 986-987 ◽  
pp. 239-242
Author(s):  
Bo Yang ◽  
Kui Hua Wu ◽  
Yi Qun Wang ◽  
Shen Quan Yang
Keyword(s):  
Transmission Line ◽  
Real Time ◽  
Transmission Lines ◽  
Rapid Growth ◽  
Power Grid ◽  
Transmission Capacity ◽  
Grid Load ◽  
Realistic Significance

The rapid growth of power grid load put forward higher requirements on the transmission capacity of line, with the growing tension of line corridors, building new transmission lines is becoming more and more difficult. Therefore, it is of realistic significance to analyze the transmission capacity of existing transmission line and fully tap the existing power grid transmission capacity. On the basis of previous studies, and consulting a large number of references, this paper summarizes and expounds the methods of improving transmission capacity by using the thermal rating analysis, introducing static thermal rating and real-time static thermal rating. Also, this paper verifies applications of the above methods in actual running environment.

scholarly journals PROPOSAL FOR MANAGING ELECTRIC ENERGY QUALITY IN THE LV GRID USING ON-LOAD TAP CHANGER WITH A STATIC SYNCHRONOUS COMPENSATOR

2018 ◽  
Vol 8 (2) ◽  
pp. 72-78
Author(s):  
Bartłomiej Mroczek ◽  
Karol Fatyga
Keyword(s):  
Reactive Power ◽  
Low Voltage ◽  
Power Grid ◽  
Electric Energy ◽  
Auxiliary Equipment ◽  
Static Synchronous Compensator ◽  
Voltage Quality ◽  
Tap Changer ◽  
Load Tap Changer

The paper proposes the use of auxiliary equipment in the low voltage network: an on-load tap changer and a static synchronous compensator (STATCOM) to improve the quality of energy supply to end users. As part of the research, a section of medium and low voltage power grid was modelled using Matlab & Simulink software, which was tested in three scenarios. The first scenario presents the operation of the power grid with the on-load tap changer installed in the transformer block. The second scenario uses the STATCOM for local reactive power compensation. Additionally, the third scenario is the combined work of the on-load tap-changer along with the STATCOM. According to the authors, the method discussed does not bring the expected results in the area of voltage quality improvement, indicating that further research is required, including tests with energy storage.

Sign in / Sign up

Export Citation Format

Share Document