scholarly journals Calculation of the Amplitude and Initial Phase of the Signal from Its Most "Reliable" Fragments

2021 ◽  
Vol 2 (1) ◽  
pp. 17-24
Author(s):  
Oleksandr Brezgunov ◽  
Sergey Brezgunov
Keyword(s):  
Initial Phase ◽  
Radio Signal ◽  
High Accuracy ◽  
Maximum Point ◽  
Radio Communication ◽  
Noise Component ◽  
Average Value ◽  
Radio Signals ◽  
Zero Values

The idea of improving the methods of processing the received radio signals used in radio communication and radiolocation systems is considered. It is proposed to consider the radio signal as a noise-resistant code with repetition of its periods (symbols), each of which carries the same information about the value of its amplitude and initial phase. The possibility of realization of coherent reception of radio signals with amplitude or biphasic discrete modulation under the influence of powerful noise on them by their most "reliable" (suitable for calculations) fragments, determined by the values of samples, received at moments when the amplitude of a received signal shall be equal to zero (samples correspond to the value of the noise component – point A) or be maximum – point E (the phase of signals shifted with respect to the phase of noise, by π/2 or 3π/4). The considered approach on processing of a mix of a signal and noise allows to define some varieties of "reliable" fragments (at difference of phases of noise and a signal on π/2 or 3π/4, at a match of zero values of signals and noise, at difference of phases of noise and a signal on the value smaller, than ±π/24) on values of samples in points A and E, and also to exclude from consideration fragments, decision on which often is erroneous. The possibility of obtaining an additional estimation ∆ of the quality of the decision on a fragment of a discrete signal (BPSK), with already calculated its average value SСР on the set of its fragments, which allows to select the best or several best fragments for the decision on the received signal is shown. Fragments with a difference of noise and signal phases on the value smaller than ±π/24 occur most often from all considered variants and allow to distinguish with high accuracy the initial phases of opposite signals (BPSK). To solve the problem, we used all possible temporal representations of fragments of signal, noise and a mixture of signal and noise, mathematical models and formulas of the theory of circuits and signals.

Thread Friction Torque in Bolted Joints

2005 ◽  
Vol 127 (4) ◽  
pp. 387-393 ◽  
Author(s):  
Sayed A. Nassar ◽  
Payam H. Matin ◽  
Gary C. Barber
Keyword(s):  
Friction Coefficient ◽  
Current Practice ◽  
Weighted Average ◽  
High Accuracy ◽  
Friction Torque ◽  
Bolted Joints ◽  
Bolted Joint ◽  
Average Value ◽  
Highly Sensitive

In this paper, formulas are developed for the calculation of the effective thread friction radius in fasteners, in order to determine the thread friction torque component. Due to the lack of exact formulas in the literature, current practice uses the average value of the minor and major thread radii, as an approximation, for determining the thread friction torque component. Results provided by these formulas are compared with those given by the current practice that uses the average value of the minor and major thread radii, instead of the exact value. It is well known that the torque-tension relationship in threaded fastener applications is highly sensitive to the friction torque components: between threads, and under the turning fastener head or nut. Even moderate variations or inaccuracies in determining the friction torque components would significantly impact the fastener tension and the joint clamp load. High accuracy in the estimation of the friction torque components is critical, as it directly affects the reliability, safety, and the quality of bolted assemblies. This analysis focuses on the thread friction torque component. The new formulas for the thread friction radius are developed for a mathematical model of a bolted joint using five assumed scenarios of the contact pressure between male and female threads. Because of the fact that the variation in the sliding speed of various points on a thread surface is insignificant, a uniform thread friction coefficient is used in the analysis. However, a contact area weighted average value is used for the thread friction coefficient. Numerical results and error analysis are presented in terms of a single nondimensional variable, namely, the ratio between the major and minor thread radii.

Measurement-based Statistical Method for Estimating and Verifying Signal Coverage and Coverage Probability in Urban Microcells

2018 ◽  
Vol 8 (6) ◽  
pp. 74
Author(s):  
Joseph Isabona ◽  
Kingsley Obahiagbon
Keyword(s):  
Outage Probability ◽  
Communication Networks ◽  
Coverage Probability ◽  
Statistical Approach ◽  
Radio Signal ◽  
Signal Strength ◽  
Signal Coverage ◽  
Radio Signals ◽  
Coverage Quality

Customer’s complaints and concerns about radio signal coverage at their home are important trigger to performance relevant drive test in the relevant area to observe the coverage quality. In this paper, statistical approach has been employed to assess the quality of the radio coverage and outage probability based on measured radio signals in an established UMTS network, operational in Ikoyi, a typical urban microcell in Nigerian environment. The results shows that the quality of radio signals at the cell edge is very poor in locations 2 and 4, as they recorded poor coverage probability performance of 89.25% and 81.72% and high outage probability performance of 10.74% and 18.28% respectively. It is also observed that the smaller the fade margin, the higher the outage probability and the lower the coverage reliability. This implies that the smaller the fade margin, the smaller the received signal strength at the MS and the more likely outage events. Hence, sufficient signal strength is needed at the mobile terminals at locations 2 and 4 in order to achieve the outage probability and coverage reliability required to effectively operate cellular communication networks.

scholarly journals Testing Radio Signal Range of Selected Components 

2018 ◽  
Vol 20 (2) ◽  
pp. 68-77
Author(s):  
Andrej Velas ◽  
Tomas Lovecek ◽  
Jan Valouch ◽  
Jacek Dworzecki ◽  
Eva Vnencakova
Keyword(s):  
Continuous Improvement ◽  
Radio Signal ◽  
Wireless Systems ◽  
Radio Communication ◽  
Security Systems ◽  
Communication Range ◽  
Testing Methodology ◽  
Radio Signals

The radio signals range of selected wireless components of security systems is defined by the area within which components can communicate properly. In practice, the range of communication between components is often insufficiently taken into account, which results in the system malfunction. There are cases where the radio signal range of wireless components was inadequate due to use in an environment constructed from non-transmitting materials.The installation of wireless systems requires the implementation of a testing methodology of radio-communication range and its continuous improvement. Currently, the procedures within EN 50 131-5-3 and EN 300 220-1 standards can be used to test the wireless components, but they do not target the range between wireless components. Dependability and functionality are the main attributes of electrical security systems and need to be verified by testing the range of wireless components.

TINGKAT KEAKURATAN DAN KEBERTERIMAAN TERJEMAHAN KALIMAT YANG MENGAKOMODASI TINDAK TUTUR KOMISIF PADA NOVEL INSURGENT (THE ACCURACY AND ACCEPTABILITY OF TRANSLATION ON THE SENTENCES WHICH ACCOMODATE COMMISSIVE SPEECH ACT IN THE INSURGENT NOVEL)

Widyaparwa ◽  
2017 ◽  
Vol 45 (2) ◽  
pp. 151-164
Author(s):  
Novita Sumarlin Putri
Keyword(s):  
Focus Group ◽  
Focus Group Discussion ◽  
Speech Act ◽  
Group Discussion ◽  
Document Analysis ◽  
High Accuracy ◽  
Pragmatic Approach ◽  
Componential Analysis ◽  
Pragmatic Aspects

Tindak tutur komisif merupakan salah satu aspek pragmatik yang harus diperhatikan oleh penerjemah ketika menerjemahkan teks. Hal itu dilakukan agar menghasilkan terjemahan yang berkualitas dari aspek keakuratan dan keberterimaan. Berdasarkan alasan tersebut, penelitian ini bertujuan mendiskripsikan tingkat keakuratan dan keberterimaan terjemahan kalimat yang mengakomodasi tindak tutur komisif dengan pendekatan pragmatik. Data yang digunakan ialah tuturan komisif dan hasil penilaian kualitas terjemahan. Data bersumber dari novel Insurgent karya Veronica Roth dan informan. Data dikumpulkan dengan cara analisis dokumen, kuesioner dan Focus Group Discussion. Selanjutnya, data dianalisis dengan cara analisis domain, taksonomi, komponensial, dan tema budaya. Hasil penelitian ini menunjukkan bahwa terjemahan dalam novel Insurgent mempunyai nilai keakuratan dan keberterimaan yang cukup tinggi. Berdasarkan penelitian ini, dapat disimpulkan bahwa tingkat keakuratan dan keberterimaan pada setiap jenis tindak tutur komisif memiliki dampak terhadap kualitas keseluruhan terjemahan kalimat yang mengandung tindak tutur komisif.Commissive speech act is one of the pragmatic aspects to regard by the translator in translating the text. It aims to produce a qualified translation in regarding accuracy and acceptability aspects. According to the aspects, this research aims to describe accuracy and acceptability of translation in sentences which accommodate commissive speech act using pragmatic approach. The data used is commissive speech and qualitative translation value result. The sources of the data are an Insurgent novel by Veronica Roth and informants. The data were collected through document analysis, questionnaire, and Focus Group Discussion then analyzed the domain, taxonomic, componential analysis, and cultural theme. The result shows that translation in the Insurgent novel has high accuracy and acceptability values. This research concludes that the accuracy and acceptability level in each commissive speech act has an impact on quality of whole translated sentences which contain commissive speech act.

Korelasi kreativitas dan motivasi kerja guru terhadap peningkatan mutu pembelajaran

2016 ◽  
Vol 1 (1) ◽  
pp. 51
Author(s):  
Muh Nashiruddin ◽  
Anharurrohman El Muhammadi
Keyword(s):  
Religious Education ◽  
Work Motivation ◽  
Sampling Technique ◽  
Islamic Education ◽  
Learning Improvement ◽  
Average Value ◽  
Teacher Creativity ◽  
Teacher Work ◽  
And Behavior

Penelitian ini bertujuan untuk mengetahui korelasi antara: 1) kreativitas guru PAI terhadap peningkatan mutu pembelajaran Pendidikan Agama dan Budi Pekerti , 2) motivasi kerja guru PAI terhadap peningkatan mutu pembelajaran Pendidikan Agama dan Budi Pekerti , dan 3) kreativitas dan motivasi kerja guru terhadap peningkatan mutu pembelajaran Pendidikan Agama dan Budi. Penelitian ini menggunakan metode deskripsi korelasional dengan melibatkan 33 orang sampel yang dipilih secara dengan metode sensus. Teknik pengumpulan data dilakukan dengan angket/kuesioner. Teknikanalisis data diawali dengan uji prasyarat yaitu uji normalitas dan linieritas. Uji hipotesis menggunakanuji regresi sederhana danuji regresi ganda. Hasil penelitian menunjukkan ; 1) Kreativitas guru berpengaruh terhadap peningkatan mutu pembelajaran Pendidikan Agama Islam dan Budi Pekerti. 2) motivasi kerja guru berpengaruh terhadap peningkatan mutu pembelajaran Pendidikan Agama Islam dan Budi Pekerti. 3) kreativitas guru dan motivasi kerja guru secara bersama-sama atau simultan berpengaruh terhadap mutu pembelajaran. Hasil analisis juga menunjukkan bahwa rata-rata nilai dari ketiga variabel tersebut hanya dapat dimasukkan dalam kategori sedang, sehingga untuk meningkatkan kinerja guru dalam mengajar perlu diperhatikan faktor-faktor lain seperti: gaji, jaminan kerja, jaminan hari tua, penghargaan atas prestasi kerja, dan sebagainya. Kata kunci: kreativitas, motivasi, mutupembelajaran Abstract [The Relationship Between Teachers’ Creativity and Motivation Toward Learning Improvement]. This research aim at determine the correlation between the creativity of teachers on the improvement of learning quality of religious education and behavior, the work motivation of teachers on the improvement of learning quality of religious education and behavior, and the creativity and the work motivation of eachers on the improvement of learning quality of religious education and behavior. This research employed a method of correlation description with 33 Islamic education teacher were selected as sample by means of census sampling. Technique of collecting data employed questionnaire. Technique of data analysis began with prerequisite of normality and linearity. Hypothesis used test of simple regression and double regression.The study revealed that teacher creativity affects on the improvement of learning quality of religious education and behavior, as well as teacher work motivation affects on the improvement of learning quality of religious education and behavior. Futhermore, analysis show that teacher creativity as well as teacher work motivation affects simultaneously on the learning quality of Islamic Education. In conclusion, the average value of those three variables may be only included into medium category. Thus, to increase teacher performance, it needs other factors, such as; salary, job guarantee, pension, appreciation of work achievement, etc. Keywords: Creativity, Motivation, Learning Quality

scholarly journals HEIDELBERG RADIOCARBON LAB – ESTABLISHING A NEW CARBON DIOXIDE EXTRACTION LINE FOR CARBONATE SAMPLES

Radiocarbon ◽  
2021 ◽  
pp. 1-10
Author(s):  
S Therre ◽  
L Proß ◽  
R Friedrich ◽  
M Trüssel ◽  
N Frank
Keyword(s):  
Radiocarbon Dating ◽  
Glass Tube ◽  
Extraction Process ◽  
High Accuracy ◽  
Repeated Measurements ◽  
Average Value ◽  
Carbon Dioxide Extraction ◽  
Favorable Conditions ◽  
Solid Piece ◽  
Environmental Physics

ABSTRACT To achieve high-precision and reproducible results from radiocarbon (14C) dating of carbonate samples in paleoclimate research, a new CO2 extraction line was designed, constructed, and characterized at the Heidelberg Radiocarbon Lab of the Institute of Environmental Physics, Heidelberg. The setup includes a circular glass-tube design, which is operated at vacuum pressure levels of the order of 10–5 mbar. The efficiency of the extraction process was assessed, showing significantly favorable conditions for solid piece samples (99.58 ± 4.69)% over powdered samples (88.28 ± 10.03)%. Process blank values are below 0.2 pMC apparent 14C activity. Repeated measurements of IAEA C2 standards with an average value of (41.09 ± 0.23) pMC attest high accuracy and reproducibility of the instrument. Six consecutive samples of 6 to 12 mg carbonate mass can be processed in one run of roughly 2.5 hours. Thus, the new setup contributes to time-efficient and reproducible radiocarbon dating results for paleoclimate research at the Institute of Environmental Physics. In a first application, Dead Carbon Fraction (DCF) values of a Holocene alpine stalagmite from Schratten Cave are presented, revealing extraordinarily high offsets between atmospheric and stalagmite 14C with DCF values between (49.4 ± 0.4)% and (61.6 ± 0.4)%.

scholarly journals Cryo-EM model validation recommendations based on outcomes of the 2019 EMDataResource challenge

2021 ◽  
Vol 18 (2) ◽  
pp. 156-164 ◽  
Author(s):  
Catherine L. Lawson ◽  
Andriy Kryshtafovych ◽  
Paul D. Adams ◽  
Pavel V. Afonine ◽  
Matthew L. Baker ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Structure Data ◽  
Model Evaluation ◽  
Data Bank ◽  
High Accuracy ◽  
Atomic Resolution ◽  
Software Developers ◽  
Data Archives ◽  
Modeling Software

AbstractThis paper describes outcomes of the 2019 Cryo-EM Model Challenge. The goals were to (1) assess the quality of models that can be produced from cryogenic electron microscopy (cryo-EM) maps using current modeling software, (2) evaluate reproducibility of modeling results from different software developers and users and (3) compare performance of current metrics used for model evaluation, particularly Fit-to-Map metrics, with focus on near-atomic resolution. Our findings demonstrate the relatively high accuracy and reproducibility of cryo-EM models derived by 13 participating teams from four benchmark maps, including three forming a resolution series (1.8 to 3.1 Å). The results permit specific recommendations to be made about validating near-atomic cryo-EM structures both in the context of individual experiments and structure data archives such as the Protein Data Bank. We recommend the adoption of multiple scoring parameters to provide full and objective annotation and assessment of the model, reflective of the observed cryo-EM map density.

The quality of the wood bonding depending on the method of applying the selected thermoplastic biopolymers

2021 ◽  
Vol 116 ◽  
pp. 78-85
Author(s):  
Aneta Gumowska ◽  
Grzegorz Kowaluk
Keyword(s):  
Shear Strength ◽  
Solid Wood ◽  
Average Value ◽  
Wood Bonding ◽  
Research Show

The quality of the wood bonding depending on the method of applying the selected thermoplastic biopolymers. The aim of the research was to determine the effect of the method of applying the biopolymer on the surface of bonding solid wood elements on the quality of the obtained adhesive connection. The results of conducted mechanical research show that the highest average value of shear strength was observed for birch lamellas bonded with PLA, both with the first and second method of application. In case of estimating the quality of the bonding of wooden elements, better results were achieved for PLA and the second method of application the "green" adhesive.

CHANGES IN THE TECHNICAL AND TECHNOLOGICAL LEVEL OF STEAM CULTIVATORS IN THE XXI CENTURY

2021 ◽  
Vol 2 (143) ◽  
pp. 174-183
Author(s):  
Andrey Yu. Nesmiyan ◽  
◽  
Anastasiya S. Kaymakova ◽  
Yuliya S. Tsench ◽  
Keyword(s):  
Weighted Average ◽  
Specific Weight ◽  
Research Purpose ◽  
Utilization Rate ◽  
Average Value ◽  
Technological Level ◽  
Short Test ◽  
Specific Material ◽  
The Cost

Most modern agricultural machines and tools consist of components, the main parameters, design features of which were justified in the first half of the twentieth century. Slowly and evolutionarily, these technical means are developing. (Research purpose) The research purpose is in identifying general trends in the technical and technological level of steam cultivators in the first quarter of the XXI century. (Materials and Methods) For the study there was analyzed the data of the short test reports of the selected machines. The production of steam cultivators in the Russian Federation is gradually increasing. (Results and discussion) For ten years of the beginning of the XXI century, only 27 machines were provided for testing, and from 2014 to 2017 – more than 40, while for "old" cultivators, the weighted average value of the tractor traction class was 2.8, for new ones it is about of four. For the study period (on average 10 years) the quality of soil cultivation in terms of such parameters as deviation from the specified depth of cultivation, crumbling and combing of the field surface has not changed much. The productivity of cultivator units increased by 7-21 percents, which is explained not only by an increase in the power of tractors, but also by an increase in the utilization rate of charge time on average from 0.72 to 0.77. The specific weight of the "new" cultivators was on average 22 kilogram-meters less than that of the "old" analogues, which can be explained by the evolution of their designs. (Conclusions) Increasing the class of tractors by one "level" the specific material consumption of the cultivators aggregated with them increases by about 58 kilogram-meters for both "old" and " new " cultivators. With an increase in the width of the tools from 4 to 16 meters, their weight will increase by 8 times, which affects the cost and operational and environmental characteristics of wide-reach cultivators.

scholarly journals Therapeutic alliance in the initial phase of psychotherapy with adolescents: different perspectives and their association with therapeutic outcomes

2016 ◽  
Vol 19 (1) ◽  
Author(s):  
Olga María Fernandez ◽  
Mariane Krause ◽  
Janet Carola Pérez
Keyword(s):  
Therapeutic Alliance ◽  
Working Alliance ◽  
Initial Phase ◽  
Psychotherapy Research ◽  
Positive Association ◽  
Outcome Questionnaire ◽  
The Third ◽  
Working Alliance Inventory ◽  
Therapeutic Outcomes

Psychotherapy research focusing on adults as well as on children and adolescents has revealed a positive association between the quality of the therapeutic alliance (TA) in the first sessions and therapeutic outcomes. Nevertheless, there is controversy regarding which perspective (of the adolescents, therapists, or parents) and what moment of evaluation (first, second, or third session) is most strongly associated with outcome. This study aims to describe the TA during the initial phase of psychotherapy with adolescents, from several perspectives, and relate it to the intermediate and final outcomes of the therapy. The study is descriptive-correlational and was conducted in naturalistic settings. The sample comprised 20 individual psychotherapeutic processes (15 females, 5 males; average age: 15.8 years; standard deviation=1.04). The variables studied were: TA, measured with the Working Alliance Inventory, applied to adolescents, therapists, and parents, and therapeutic outcomes, measured using Lambert’s Outcome Questionnaire (OQ- 45.2). The results show that the TA improved from session one to session three, both in the adolescents and the therapists. The TA, as perceived by the adolescents in the third session, is positively correlated with final outcomes (r=-.732*, P=.025). The TA evaluated from the therapists’ perspective in the third session, specifically the bond component of the TA, predicts the final success of psychotherapy with adolescent patients [β=0.426, Exp. (B)=1.531, degree of freedom=1, P=0.034]. The importance of the initial construction of the working alliance by both participants is discussed.

Sign in / Sign up

Export Citation Format

Share Document