scholarly journals Low Noise Amplifier with Improved Gain and Reduced Noise-Figure in 90nm CMOS Technology

2021 ◽  
pp. 85-94
Author(s):  
Dr. Rashmi S B ◽  
Mr. Raghavendra B ◽  
Mr. Sanketh V
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Ultra Wideband ◽  
Common Source ◽  
Frequency Range ◽  
Common Gate ◽  
Noise Amplifier

A CMOS low noise amplifier (LNA) for ultra-wideband (UWB) wireless applications is presented in this paper. The proposed CMOS low noise amplifier (LNA) is designed using common-gate (CG) topology as the first stage to achieve ultra-wideband input matching. The common-gate (CG) is cascaded with common- source (CS) topology with current-reused configuration to enhance the gain and noise figure (NF) performance of the LNA with low power. The Buffer stage is used as output matching network to improve the reflection coefficient. The proposed low noise amplifier (LNA) is implemented using CADENCE Virtuoso Analog and Digital Design Environment tool in 90nm CMOS technology. The LNA provides a forward voltage gain or power gain (S21) of 32.34dB , a minimum noise figure of 2dB, a reverse-isolation (S12) of less than - 38.74dB and an output reflection coefficient (S22) of less than -7.4dB for the entire ultra-wideband frequency range. The proposed LNA has an input reflection coefficient (S11) of less than -10dB for the ultra-wideband frequency range. It achieves input referred 1-dB compression point of 78.53dBm and input referred 3-dB compression point of 13dBm. It consumes only 24.226mW of power from a Vdd supply of 0.7V.

scholarly journals A 0.7 V, Ultra-Wideband Common Gate LNA with Feedback Body Bias Topology for Wireless Applications

2018 ◽  
Vol 8 (4) ◽  
pp. 42
Author(s):  
Vikram Singh ◽  
Sandeep Arya ◽  
Manoj Kumar
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Average Power ◽  
Low Noise ◽  
Ultra Wideband ◽  
Common Source ◽  
Power Gain ◽  
Wireless Applications ◽  
Common Gate ◽  
Noise Amplifier

An ultra-wideband (UWB) low noise amplifier (LNA) for 3.3–13.0 GHz wireless applications using 90 nm CMOS is proposed in this paper. The proposed LNA uses an improved common-gate (CG) topology utilizing feedback body biasing (FBB), which improves noise figure (NF) by a considerable amount. Parallel-series tuned LC network was used between the common-gate first stage and the cascoded common-source (CS) stage to achieve the maximum signal flow from CG to CS stage. Improved CS topology with a series inductor at the drain terminal in the second stage connected and cascoded CS third stage provides high power gain (S21) and bandwidth enhancement throughout the complete UWB. A common-drain buffer stage at the output provides high output reflection coefficient (S22). It achieves an average power gain (S21) of 14.7 ± 0.5 dB with a noise figure (NF) of 3.0–3.7 dB. It has an input reflection coefficient (S11) less than −11.7 dB for 3.3–13.0 GHz frequency and output reflection coefficient (S22) of less than −10.6 dB with a very high reversion isolation (S12) of less than −72.4 dB. It consumes only 5.2 mW from a 0.7 V power supply.

A 3–14 GHz, Self-Body Biased Common-Gate UWB LNA for Wireless Applications in 90 nm CMOS

2019 ◽  
Vol 28 (04) ◽  
pp. 1950056 ◽  
Author(s):  
Vikram Singh ◽  
Sandeep Kumar Arya ◽  
Manoj Kumar
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Impedance Matching ◽  
Low Noise ◽  
Ultra Wideband ◽  
Common Source ◽  
Cmos Process ◽  
Frequency Range ◽  
Continuous Growth ◽  
Common Gate

Inspired from continuous growth in the field of low power and low noise wireless communication devices, a low noise amplifier (LNA) using self-body biased common-gate (CG) configuration is presented in this paper. The proposed LNA is designed for 3–14[Formula: see text]GHz ultra-wideband (UWB) frequency range using 90[Formula: see text]nm CMOS process. Common-gate configuration with self-body biasing has been used at the input stage to provide wideband input matching with low noise figure (NF) for the complete UWB frequency. An impedance matching network consisting of parallel to series RLC network has been used between common-gate and cascaded common source (CS) stages. Two stages of the CS configuration have been used for bandwidth enhancement and to increase the power gain (S[Formula: see text]) with acceptable NF. Buffer stage at the output has been used to achieve output reflection coefficient (S[Formula: see text]) less than [Formula: see text]10.8[Formula: see text]dB. The proposed LNA achieves an average S[Formula: see text] of 15.9[Formula: see text][Formula: see text][Formula: see text]0.7[Formula: see text]dB with a maximum of 16.7[Formula: see text]dB at 3.0[Formula: see text]GHz and NF of 1.68–2.7[Formula: see text]dB for 3.1–10.6[Formula: see text]GHz UWB frequency range. It provides input reflection coefficient (S[Formula: see text]) less than [Formula: see text]10.2[Formula: see text]dB, reverse isolation (S[Formula: see text]) less than [Formula: see text]75.8[Formula: see text]dB and a NF of 1.68–4.0[Formula: see text]dB throughout the proposed UWB frequency range. The proposed LNA provides input 1[Formula: see text]dB compression point (P1dB) of [Formula: see text]13[Formula: see text]dBm and input third-order intercept point (IIP3) of [Formula: see text]8[Formula: see text]dBm at 6[Formula: see text]GHz. It consumes 20.1[Formula: see text]mW of power from a 1.2[Formula: see text]V power supply.

A 79GHz Adaptive Gain Low Noise Amplifier for Radar Receivers

2018 ◽  
Vol 7 (2.24) ◽  
pp. 227
Author(s):  
J Manjula ◽  
A Ruhan Bevi
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
Input Power ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Center Frequency ◽  
Common Source ◽  
Adaptive Biasing ◽  
Noise Amplifier

This paper presents an Adaptive Gain 79GHz Low Noise Amplifier (LNA) suitable for Radars applications. The circuit schematic is a two stage LNA consists of Differential cascode configuration followed by a simple common source amplifier with an Adaptive Biasing (ADB) circuit. Adaptive biasing is a three- stage common source amplifier to decrease output voltage as input power increases. The circuit is simulated in 180nm CMOS technology and the simulation results have proved that the circuit operates at the center frequency 79GHz with adaptive biasing for adaptive gain. The gain analysis shows a decrease of 35-30dB with an increase in input power -50 to 0 dB. At 79GHz the circuit has achieved the input reflection coefficient (S11) of -24.7dB, reverse isolation (S12) of -3 dB, forward transmission coefficient (S21) of -2.97dB and output reflection coefficient (S22) of -5.62 dB with the reduced noise figure of 0.9 dB and a power consumption of 236 mW.  

scholarly journals A 0.18um CMOS Low Noise Amplifier for 3-5ghz UWB Receivers

2018 ◽  
Vol 7 (3.6) ◽  
pp. 84
Author(s):  
N Malika Begum ◽  
W Yasmeen
Keyword(s):  
Power Supply ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Ultra Wideband ◽  
Noise Amplifier ◽  
5 Ghz ◽  
Chebyshev Filter ◽  
Minimum Noise

This paper presents an Ultra-Wideband (UWB) 3-5 GHz Low Noise Amplifier (LNA) employing Chebyshev filter. The LNA has been designed using Cadence 0.18um CMOS technology. Proposed LNA achieves a minimum noise figure of 2.2dB, power gain of 9dB.The power consumption is 6.3mW from 1.8V power supply.  

scholarly journals A 2.4 GHz low noise amplifier design at 130nm CMOS technology using common gate topology for WiFi / WiMAX application

2017 ◽  
Vol 7 (1.3) ◽  
pp. 69
Author(s):  
M. Ramana Reddy ◽  
N.S Murthy Sharma ◽  
P. Chandra Sekhar
Keyword(s):  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Low Power Consumption ◽  
Common Gate ◽  
Chip Size ◽  
Overall Performance ◽  
Amplifier Design ◽  
Noise Amplifier

The proposed work shows an innovative designing in TSMC 130nm CMOS technology. A 2.4 GHz common gate topology low noise amplifier (LNA) using an active inductor to attain the low power consumption and to get the small chip size in layout design. By using this Common gate topology achieves the noise figure of 4dB, Forward gain (S21) parameter of 14.7dB, and the small chip size of 0.26 mm, while 0.8mW power consuming from a 1.1V in 130nm CMOS gives the better noise figure and improved the overall performance.

Inductive Feedback Technique for Design of High Gain 0.18μm CMOS LNA for 5G Applications

2021 ◽  
pp. 2150236
Author(s):  
Anjana Jyothi Banu ◽  
G. Kavya ◽  
D. Jahnavi
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Common Source ◽  
Matching Network ◽  
Input Matching ◽  
Cmos Lna ◽  
Noise Amplifier

A 26[Formula: see text]GHz low-noise amplifier (LNA) designed for 5G applications using 0.18[Formula: see text][Formula: see text]m CMOS technology is proposed in this paper. The circuit includes a common-source in the first stage to suppress the noise in the amplifier. The successive stage has a Cascode topology along with an inductive feedback to improve the power gain. The input matching network is designed to achieve the input reflection coefficient less than [Formula: see text]7dB at the intended frequency. The matching network at the output is designed using inductor–capacitor (LC) components connected in parallel to attain the output reflection coefficient of [Formula: see text]10[Formula: see text]dB. Due to the inductor added in feedback at the second stage. The [Formula: see text] obtained is 18.208[Formula: see text]dB at 26[Formula: see text]GHz with a noise figure (NF) of 2.8[Formula: see text]dB. The power supply given to the LNA is 1.8[Formula: see text]V. The simulation and layout of the presented circuit are performed using Cadence Virtuoso software.

scholarly journals Design And Analysis Of CMOS Low Noise Amplifier Circuit For 5-GHz Cascode and Folded Cascode In 180nm Technology

2018 ◽  
Vol 7 (3) ◽  
pp. 143
Author(s):  
T. Kanthi ◽  
D. Sharath Babu Rao
Keyword(s):  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Common Source ◽  
Power Gain ◽  
Amplifier Circuit ◽  
Folded Cascode ◽  
Noise Amplifier ◽  
5 Ghz

This paper is about Low noise amplifier topologies based on 0.18µm CMOS technology. A common source stage with inductive degeneration, cascode stage and folded cascode stage is designed, simulated and the performance has been analyzed. The LNA’s are designed in 5GHz. The LNA of cascode stage of noise figure (NF) 2.044dB and power gain 4.347 is achieved. The simulations are done in cadence virtuoso spectre RF.

A wideband CMOS single-ended low noise amplifier employing negative resistance technique

2018 ◽  
Vol 32 (06) ◽  
pp. 1850068 ◽  
Author(s):  
Benqing Guo ◽  
Hongpeng Chen ◽  
Xuebing Wang ◽  
Jun Chen ◽  
Yueyue Li ◽  
...  
Keyword(s):  
Power Dissipation ◽  
Noise Figure ◽  
Cmos Technology ◽  
Negative Resistance ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Common Gate ◽  
Noise Amplifier ◽  
Maximal Gain ◽  
Resistance Structure

A wideband common-gate CMOS low noise amplifier with negative resistance technique is proposed. A novel single-ended negative resistance structure is employed to improve gain and noise of the LNA. The inductor resonating is adopted at the input stage and load stage to meet wideband matching and compensate gain roll-off at higher frequencies. Implemented in a 0.18 [Formula: see text]m CMOS technology, the proposed LNA demonstrates in simulations a maximal gain of 16.4 dB across the 3 dB bandwidth of 0.2–3 GHz. The in-band noise figure of 3.4–4.7 dB is obtained while the IIP3 of 5.3–6.8 dBm and IIP2 of 12.5–17.2 dBm are post-simulated in the designed frequency band. The LNA core consumes a power dissipation of 3.8 mW under a 1.5 V power supply.

scholarly journals Design And Analysis Of CMOS Low Noise Amplifier Circuit For 5-GHz Cascode and Folded Cascode In 180nm Technology

2018 ◽  
Vol 7 (3) ◽  
pp. 149
Author(s):  
T. Kanthi ◽  
D. Sharath Babu Rao
Keyword(s):  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Common Source ◽  
Power Gain ◽  
Amplifier Circuit ◽  
Folded Cascode ◽  
Noise Amplifier ◽  
5 Ghz

This paper is about Low noise amplifier topologies based on 0.18µm CMOS technology. A common source stage with inductive degeneration, cascode stage and folded cascode stage is designed, simulated and the performance has been analyzed. The LNA’s are designed in 5GHz. The LNA of cascode stage of noise figure (NF) 2.044dB and power gain 4.347 is achieved. The simulations are done in cadence virtuoso spectre RF.

scholarly journals Design and Implementation of Low Noise Amplifier At 60ghz using Current Mirror Feedback

2019 ◽  
Vol 8 (9S3) ◽  
pp. 249-254
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Single Stage ◽  
Common Source ◽  
Small Signal ◽  
Total Size ◽  
Noise Amplifier

This discourse used 45nm CMOS technology to design a Low noise amplifier for a Noise figure < 2dB and gain greater than 13dB at the 60GHz unlicensed band of frequency. A single stage, primary cascode LNA is modeled and its small signal model is analyzed. Common source structure is hired in the driver stage to escalate the output power with single stage contours. To enhance small signal gain, simple active transistor feedback and cascode feedback configurations are designed and appended to the basic LNA. In addition to this, current re-use inductor is designed and added to the cascode amplifier which is deliberated to give low power and low noise figure. Small signal analysis of simple active transistor feedback and current re-use inductor has been presented. The measurement results indicated that the input match and the output gain at 60GHz achieves -8dB and 13dB respectively with the supply voltage of 900mV. The frequency response obtained is a narrow band response with 6GHz of bandwidth. The circuit is simulated by Cadence Virtuoso tool. The layout of the related circuit is drawn by means of the Virtuoso Layout editor with total size of 0.1699μm2.

Sign in / Sign up

Export Citation Format

Share Document