scholarly journals The impact of deforestation in the Amazonian atmospheric radiative balance: a remote sensing assessment

2012 ◽  
Vol 12 (6) ◽  
pp. 14837-14874 ◽  
Author(s):  
E. T. Sena ◽  
P. Artaxo ◽  
A. L. Correia
Keyword(s):  
Water Vapour ◽  
Biomass Burning ◽  
Radiative Forcing ◽  
Surface Albedo ◽  
Radiative Effect ◽  
Water Vapour Content ◽  
Albedo Change ◽  
Direct Radiative Forcing ◽  
The Mean ◽  
The Impact

Abstract. This paper addresses the Amazonian radiative budget after considering three aspects of deforestation: (i) the emission of aerosols from biomass burning due to forest fires; (ii) changes in surface albedo after deforestation and (iii) modifications in the column water vapour amount over deforested areas. Simultaneous Clouds and the Earth's Radiant Energy System (CERES) shortwave fluxes and aerosol optical depth (AOD) retrievals from the Moderate Resolution Imaging SpectroRadiometer (MODIS) were analysed during the peak of the biomass burning seasons (August and September) from 2000 to 2009. A discrete-ordinate radiative transfer (DISORT) code was used to extend instantaneous remote sensing radiative forcing assessments into 24-h averages. The mean direct radiative forcing of aerosols at the top of the atmosphere (TOA) during the biomass burning season for the 10-yr studied period was −5.6 ± 1.7 W m−2. Furthermore, the spatial distribution of the direct radiative forcing of aerosols over Amazon was obtained for the biomass burning season of each year. It was observed that for high AOD (larger than 1 at 550 nm) the imbalance in the radiative forcing at the TOA may be as high as −20 W m−2 locally. The surface reflectance plays a major role in the aerosol direct radiative effect. The study of the effects of biomass burning aerosols over different surface types shows that the direct radiative forcing is systematically more negative over forest than over savannah-like covered areas. Values of −15.7 ± 2.4 W m−2/τ550 nm and −9.3 ± 1.7 W m−2/τ550 nm were calculated for the mean daily aerosol forcing efficiencies over forest and savannah-like vegetation respectively. The overall mean annual albedo-change radiative forcing due to deforestation over the state of Rondônia, Brazil, was determined as −7.3 ± 0.9 W m−2. Biomass burning aerosols impact the radiative budget for approximately two months per year, whereas the surface albedo impact is observed throughout the year. Because of this difference, the estimated impact in the Amazonian annual radiative budget due to surface albedo-change is approximately 6 times higher than the impact due to aerosol emissions. The influence of atmospheric water vapour content in the radiative budget was also studied using AERONET column water vapour. It was observed that column water vapour is in average smaller by about 0.35 cm over deforested areas compared to forested areas. Our results indicate that this drying impact contributes to an increase in the shortwave radiative effect that varies from 0.4 W m−2 to 1.2 W m−2, depending on the column water vapour content before deforestation. The large radiative forcing values presented in this study point out that deforestation has strong implications in convection, cloud development and photosynthesis rate over the Amazon region.

scholarly journals Spatial variability of the direct radiative forcing of biomass burning aerosols and the effects of land use change in Amazonia

2013 ◽  
Vol 13 (3) ◽  
pp. 1261-1275 ◽  
Author(s):  
E. T. Sena ◽  
P. Artaxo ◽  
A. L. Correia
Keyword(s):  
Land Use ◽  
Land Use Change ◽  
Water Vapour ◽  
Biomass Burning ◽  
Radiative Forcing ◽  
Surface Albedo ◽  
Water Vapour Content ◽  
Direct Radiative Forcing ◽  
The Mean ◽  
The Impact

Abstract. This paper addresses the Amazonian shortwave radiative budget over cloud-free conditions after considering three aspects of deforestation: (i) the emission of aerosols from biomass burning due to forest fires; (ii) changes in surface albedo after deforestation; and (iii) modifications in the column water vapour amount over deforested areas. Simultaneous Clouds and the Earth's Radiant Energy System (CERES) shortwave fluxes and aerosol optical depth (AOD) retrievals from the Moderate Resolution Imaging SpectroRadiometer (MODIS) were analysed during the peak of the biomass burning seasons (August and September) from 2000 to 2009. A discrete-ordinate radiative transfer (DISORT) code was used to extend instantaneous remote sensing radiative forcing assessments into 24-h averages. The mean direct radiative forcing of aerosols at the top of the atmosphere (TOA) during the biomass burning season for the 10-yr studied period was −5.6 ± 1.7 W m−2. Furthermore, the spatial distribution of the direct radiative forcing of aerosols over Amazonia was obtained for the biomass burning season of each year. It was observed that for high AOD (larger than 1 at 550 nm) the maximum daily direct aerosol radiative forcing at the TOA may be as high as −20 W m−2 locally. The surface reflectance plays a major role in the aerosol direct radiative effect. The study of the effects of biomass burning aerosols over different surface types shows that the direct radiative forcing is systematically more negative over forest than over savannah-like covered areas. Values of −15.7 ± 2.4 W m−2τ550 nm and −9.3 ± 1.7 W m−2τ550 nm were calculated for the mean daily aerosol forcing efficiencies over forest and savannah-like vegetation respectively. The overall mean annual land use change radiative forcing due to deforestation over the state of Rondônia, Brazil, was determined as −7.3 ± 0.9 W m−2. Biomass burning aerosols impact the radiative budget for approximately two months per year, whereas the surface albedo impact is observed throughout the year. Because of this difference, the estimated impact in the Amazonian annual radiative budget due to surface albedo-change is approximately 6 times higher than the impact due to aerosol emissions. The influence of atmospheric water vapour content in the radiative budget was also studied using AERONET column water vapour. It was observed that column water vapour is on average smaller by about 0.35 cm (around 10% of the total column water vapour) over deforested areas compared to forested areas. Our results indicate that this drying contributes to an increase in the shortwave radiative forcing, which varies from 0.4 W m−2 to 1.2 W m−2 depending on the column water vapour content before deforestation. The large radiative forcing values presented in this study point out that deforestation could have strong implications in convection, cloud development and the ratio of direct to diffuse radiation, which impacts carbon uptake by the forest.

scholarly journals Radiative impact of an extreme Arctic biomass-burning event

2018 ◽  
Vol 18 (12) ◽  
pp. 8829-8848 ◽  
Author(s):  
Justyna Lisok ◽  
Anna Rozwadowska ◽  
Jesper G. Pedersen ◽  
Krzysztof M. Markowicz ◽  
Christoph Ritter ◽  
...  
Keyword(s):  
Radiative Transfer ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Biomass Burning ◽  
Radiative Forcing ◽  
Radiation Budget ◽  
Plane Parallel ◽  
Direct Radiative Forcing ◽  
The Mean ◽  
The Impact

Abstract. The aim of the presented study was to investigate the impact on the radiation budget of a biomass-burning plume, transported from Alaska to the High Arctic region of Ny-Ålesund, Svalbard, in early July 2015. Since the mean aerosol optical depth increased by the factor of 10 above the average summer background values, this large aerosol load event is considered particularly exceptional in the last 25 years. In situ data with hygroscopic growth equations, as well as remote sensing measurements as inputs to radiative transfer models, were used, in order to estimate biases associated with (i) hygroscopicity, (ii) variability of single-scattering albedo profiles, and (iii) plane-parallel closure of the modelled atmosphere. A chemical weather model with satellite-derived biomass-burning emissions was applied to interpret the transport and transformation pathways. The provided MODTRAN radiative transfer model (RTM) simulations for the smoke event (14:00 9 July–11:30 11 July) resulted in a mean aerosol direct radiative forcing at the levels of −78.9 and −47.0 W m−2 at the surface and at the top of the atmosphere, respectively, for the mean value of aerosol optical depth equal to 0.64 at 550 nm. This corresponded to the average clear-sky direct radiative forcing of −43.3 W m−2, estimated by radiometer and model simulations at the surface. Ultimately, uncertainty associated with the plane-parallel atmosphere approximation altered results by about 2 W m−2. Furthermore, model-derived aerosol direct radiative forcing efficiency reached on average −126 W m-2/τ550 and −71 W m-2/τ550 at the surface and at the top of the atmosphere, respectively. The heating rate, estimated at up to 1.8 K day−1 inside the biomass-burning plume, implied vertical mixing with turbulent kinetic energy of 0.3 m2 s−2.

scholarly journals Impact of a Strong Biomass Burning Event on the Radiative Forcing in the Arctic

2017 ◽  
Author(s):  
Justyna Lisok ◽  
Anna Rozwadowska ◽  
Jesper G. Pedersen ◽  
Krzysztof M. Markowicz ◽  
Christoph Ritter ◽  
...  
Keyword(s):  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Biomass Burning ◽  
Radiative Forcing ◽  
Radiation Budget ◽  
The Arctic ◽  
Plane Parallel ◽  
Direct Radiative Forcing ◽  
The Mean ◽  
The Impact

Abstract. The aim of the presented study was to investigate the impact on the radiation budget of biomass burning smoke plume transported from Alaska to high Arctic region (Ny-Alesund, Svalbard) in early July 2015. This high aerosol load event is considered exceptional in the last 25 years with mean aerosol optical depth increased by the factor of 10 in comparison to the average summer background values. We utilised in-situ data with hygroscopic growth equations as well as remote sensing measurements as inputs to radiative transfer models with an objective to estimate biases associated with (i) hygroscopicity, (ii) variability of ω profiles and (iii) plane-parallel closure of the modelled atmosphere. A chemical weather model with satellite-derived biomass burning emissions was used to interpret the transport and transformations pathways. Provided MODTRAN simulations resulted in the mean aerosol direct radiative forcing on the level of −78.9 W m−2 and −47.0 W m−2 at the surface and the top of the atmosphere respectively for the mean value of aerosol optical depth equal to 0.64 at 550 nm. It corresponded to the average clear-sky direct radiative forcing of −43.3 W m−2 estimated by radiometers and model simulations. Furthermore, model-derived aerosol direct radiative forcing efficiency reached on average −126 W m−2 / τ550 and −71 W m−2 / τ550 at the surface and at the top of the atmosphere. Estimated heating rate up to 1.8 K day−1 inside the BB plume implied vertical mixing with the turbulent kinetic energy of 0.3 m2 s−2. Ultimately, uncertainty connected with the plane-parallel atmosphere approximation altered results by about 2 W m−2.

scholarly journals A novel methodology for large-scale daily assessment of the direct radiative forcing of smoke aerosols

2015 ◽  
Vol 15 (10) ◽  
pp. 5471-5483 ◽  
Author(s):  
E. T. Sena ◽  
P. Artaxo
Keyword(s):  
Remote Sensing ◽  
Spatial Distribution ◽  
Radiative Transfer ◽  
Biomass Burning ◽  
Satellite Remote Sensing ◽  
Radiative Forcing ◽  
High Temporal Resolution ◽  
Radiation Balance ◽  
Direct Radiative Forcing ◽  
The Impact

Abstract. A new methodology was developed for obtaining daily retrievals of the direct radiative forcing of aerosols (24h-DARF) at the top of the atmosphere (TOA) using satellite remote sensing. Simultaneous CERES (Clouds and Earth's Radiant Energy System) shortwave flux at the top of the atmosphere and MODIS (Moderate Resolution Spectroradiometer) aerosol optical depth (AOD) retrievals were used. To analyse the impact of forest smoke on the radiation balance, this methodology was applied over the Amazonia during the peak of the biomass burning season from 2000 to 2009. To assess the spatial distribution of the DARF, background smoke-free scenes were selected. The fluxes at the TOA under clean conditions (Fcl) were estimated as a function of the illumination geometry (θ0) for each 0.5° × 0.5° grid cell. The instantaneous DARF was obtained as the difference between the clean (Fcl (θ0)) and the polluted flux at the TOA measured by CERES in each cell (Fpol (θ0)). The radiative transfer code SBDART (Santa Barbara DISORT Radiative Transfer model) was used to expand instantaneous DARFs to 24 h averages. This new methodology was applied to assess the DARF both at high temporal resolution and over a large area in Amazonia. The spatial distribution shows that the mean 24h-DARF can be as high as −30 W m−2 over some regions. The temporal variability of the 24h-DARF along the biomass burning season was also studied and showed large intraseasonal and interannual variability. We showed that our methodology considerably reduces statistical sources of uncertainties in the estimate of the DARF, when compared to previous approaches. DARF assessments using the new methodology agree well with ground-based measurements and radiative transfer models. This demonstrates the robustness of the new proposed methodology for assessing the radiative forcing for biomass burning aerosols. To our knowledge, this is the first time that satellite remote sensing assessments of the DARF have been compared with ground-based DARF estimates.

scholarly journals CO<sub>2</sub>-equivalence metrics for surface albedo change based on the radiative forcing concept: a critical review

2021 ◽  
Vol 21 (12) ◽  
pp. 9887-9907
Author(s):  
Ryan M. Bright ◽  
Marianne T. Lund
Keyword(s):  
Radiative Forcing ◽  
Surface Albedo ◽  
Decision Makers ◽  
Spatial Disparity ◽  
Time Dependency ◽  
Considerable Research ◽  
Albedo Change ◽  
Co2 Equivalent ◽  
The Impact ◽  
Change Mitigation

Abstract. Management of Earth's surface albedo is increasingly viewed as an important climate change mitigation strategy both on (Seneviratne et al., 2018) and off (Field et al., 2018; Kravitz et al., 2018) the land. Assessing the impact of a surface albedo change involves employing a measure like radiative forcing (RF) which can be challenging to digest for decision-makers who deal in the currency of CO2-equivalent emissions. As a result, many researchers express albedo change (Δα) RFs in terms of their CO2-equivalent effects, despite the lack of a standard method for doing so, such as there is for emissions of well-mixed greenhouse gases (WMGHGs; e.g., IPCC AR5, Myhre et al., 2013). A major challenge for converting Δα RFs into their CO2-equivalent effects in a manner consistent with current IPCC emission metric approaches stems from the lack of a universal time dependency following the perturbation (perturbation “lifetime”). Here, we review existing methodologies based on the RF concept with the goal of highlighting the context(s) in which the resulting CO2-equivalent metrics may or may not have merit. To our knowledge this is the first review dedicated entirely to the topic since the first CO2-eq. metric for Δα surfaced 20 years ago. We find that, although there are some methods that sufficiently address the time-dependency issue, none address or sufficiently account for the spatial disparity between the climate response to CO2 emissions and Δα – a major critique of Δα metrics based on the RF concept (Jones et al., 2013). We conclude that considerable research efforts are needed to build consensus surrounding the RF “efficacy” of various surface forcing types associated with Δα (e.g., crop change, forest harvest), and the degree to which these are sensitive to the spatial pattern, extent, and magnitude of the underlying surface forcings.

scholarly journals CO<sub>2</sub>-equivalence metrics for surface albedo change based on the radiative forcing concept: A critical review

2020 ◽  
Author(s):  
Ryan M. Bright ◽  
Marianne T. Lund
Keyword(s):  
Radiative Forcing ◽  
Surface Albedo ◽  
Decision Makers ◽  
Spatial Disparity ◽  
Time Dependency ◽  
Considerable Research ◽  
Albedo Change ◽  
Co2 Equivalent ◽  
The Impact ◽  
Change Mitigation

Abstract. Management of Earth's surface albedo is increasingly viewed as an important climate change mitigation strategy both on (Seneviratne et al., 2018) and off (Field et al., 2018; Kravitz et al., 2018) the land. Assessing the impact of a surface albedo change involves employing a measure like radiative forcing (RF) which can be challenging to digest for decision-makers who deal in the currency of CO2-equivalent emissions. As a result, many researchers express albedo change (Δα) RFs in terms of their CO2-equivalent effects, despite the lack of a standard method for doing so, such as there is for emissions of well-mixed greenhouse gases (WMGHGs; e.g., IPCC AR5, Myhre et al. (2013)). A major challenge for converting Δα RFs into their CO2-equivalant effects in a manner consistent with current IPCC emission metric approaches stems from the lack of a universal time-dependency following the perturbation (perturbation lifetime). Here, we review existing methodologies based on the RF concept with the goal of highlighting the context(s) in which the resulting CO2-equivalent metrics may or may not have merit. To our knowledge this is the first review dedicated entirely to the topic since the first CO2-eq. metric for Δα surfaced 20 years ago. We find that, although there are some methods that sufficiently address the time-dependency issue, none address or sufficiently account for the spatial disparity between the climate response to CO2 emissions and Δα – a major critique of Δα metrics based on the RF concept (Jones et al., 2013). We conclude that considerable research efforts are needed to build consensus surrounding the RF efficacy of various surface forcing types associated with Δα (e.g., crop change, forest harvest, etc.), and the degree to which these are sensitive to the spatial pattern, extent, and magnitude of the underlying surface forcings.

Radiative forcing over the Arctic of aerosols from the August 2017 Canadian and Greenlandic wildfires

2021 ◽  
Author(s):  
Filippo Calì Quaglia ◽  
Daniela Meloni ◽  
Alcide Giorgio di Sarra ◽  
Tatiana Di Iorio ◽  
Virginia Ciardini ◽  
...  
Keyword(s):  
Radiative Transfer ◽  
Radiative Forcing ◽  
Solar Zenith Angle ◽  
Surface Albedo ◽  
High Arctic ◽  
The Arctic ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Aerosol Layer ◽  
Radiative Effect

&lt;p&gt;Extended and intense wildfires occurred in Northern Canada and, unexpectedly, on the Greenlandic West coast during summer 2017. The thick smoke plume emitted into the atmosphere was transported to the high Arctic, producing one of the largest impacts ever observed in the region. Evidence of Canadian and Greenlandic wildfires was recorded at the Thule High Arctic Atmospheric Observatory (THAAO, 76.5&amp;#176;N, 68.8&amp;#176;W, www.thuleatmos-it.it) by a suite of instruments managed by ENEA, INGV, Univ. of Florence, and NCAR. Ground-based observations of the radiation budget have allowed quantification of the surface radiative forcing at THAAO.&amp;#160;&lt;/p&gt;&lt;p&gt;Excess biomass burning chemical tracers such as CO, HCN, H2CO, C2H6, and NH3 were&amp;#160; measured in the air column above Thule starting from August 19 until August 23. The aerosol optical depth (AOD) reached a peak value of about 0.9 on August 21, while an enhancement of wildfire compounds was&amp;#160; detected in PM10. The measured shortwave radiative forcing was -36.7 W/m2 at 78&amp;#176; solar zenith angle (SZA) for AOD=0.626.&lt;/p&gt;&lt;p&gt;MODTRAN6.0 radiative transfer model (Berk et al., 2014) was used to estimate the aerosol radiative effect and the heating rate profiles at 78&amp;#176; SZA. Measured temperature profiles, integrated water vapour, surface albedo, spectral AOD and aerosol extinction profiles from CALIOP onboard CALIPSO were used as model input. The peak&amp;#160; aerosol heating rate (+0.5 K/day) was&amp;#160; reached within the aerosol layer between 8 and 12 km, while the maximum radiative effect (-45.4 W/m2) is found at 3 km, below the largest aerosol layer.&lt;/p&gt;&lt;p&gt;The regional impact of the event that occurred on August 21 was investigated using a combination of atmospheric radiative transfer modelling with measurements of AOD and ground surface albedo from MODIS. The aerosol properties used in the radiative transfer model were constrained by in situ measurements from THAAO. Albedo data over the ocean have been obtained from Jin et al. (2004). Backward trajectories produced through HYSPLIT simulations (Stein et al., 2015) were also employed to trace biomass burning plumes.&lt;/p&gt;&lt;p&gt;The radiative forcing efficiency (RFE) over land and ocean was derived, finding values spanning from -3 W/m2 to -132 W/m2, depending on surface albedo and solar zenith angle. The fire plume covered a vast portion of the Arctic, with large values of the daily shortwave RF (&lt; -50 W/m2) lasting for a few days. This large amount of aerosol is expected to influence cloud properties in the Arctic, producing significant indirect radiative effects.&lt;/p&gt;

scholarly journals Contrasting the direct radiative effect and direct radiative forcing of aerosols

2014 ◽  
Vol 14 (11) ◽  
pp. 5513-5527 ◽  
Author(s):  
C. L. Heald ◽  
D. A. Ridley ◽  
J. H. Kroll ◽  
S. R. H. Barrett ◽  
K. E. Cady-Pereira ◽  
...  
Keyword(s):  
Energy Balance ◽  
Radiative Forcing ◽  
Transport Model ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Radiative Effect ◽  
Chemical Transport Model ◽  
Anthropogenic Aerosols ◽  
Anthropogenic Aerosol ◽  
Direct Radiative Forcing

Abstract. The direct radiative effect (DRE) of aerosols, which is the instantaneous radiative impact of all atmospheric particles on the Earth's energy balance, is sometimes confused with the direct radiative forcing (DRF), which is the change in DRE from pre-industrial to present-day (not including climate feedbacks). In this study we couple a global chemical transport model (GEOS-Chem) with a radiative transfer model (RRTMG) to contrast these concepts. We estimate a global mean all-sky aerosol DRF of −0.36 Wm−2 and a DRE of −1.83 Wm−2 for 2010. Therefore, natural sources of aerosol (here including fire) affect the global energy balance over four times more than do present-day anthropogenic aerosols. If global anthropogenic emissions of aerosols and their precursors continue to decline as projected in recent scenarios due to effective pollution emission controls, the DRF will shrink (−0.22 Wm−2 for 2100). Secondary metrics, like DRE, that quantify temporal changes in both natural and anthropogenic aerosol burdens are therefore needed to quantify the total effect of aerosols on climate.

scholarly journals Diurnal cycle of the dust instantaneous direct radiative forcing over the Arabian Peninsula

2015 ◽  
Vol 15 (16) ◽  
pp. 9537-9553 ◽  
Author(s):  
S. Osipov ◽  
G. Stenchikov ◽  
H. Brindley ◽  
J. Banks
Keyword(s):  
Diurnal Cycle ◽  
Radiative Forcing ◽  
Surface Albedo ◽  
Arabian Peninsula ◽  
Extreme Values ◽  
Radiation Transport ◽  
Atmospheric Composition ◽  
Diurnal Variability ◽  
Wide Range ◽  
Direct Radiative Forcing

Abstract. In this study we attempted to better quantify radiative effects of dust over the Arabian Peninsula and their dependence on input parameters. For this purpose we have developed a stand-alone column radiation transport model coupled with the Mie, T-matrix and geometric optics calculations and driven by reanalysis meteorological fields and atmospheric composition. Numerical experiments were carried out for a wide range of aerosol optical depths, including extreme values developed during the dust storm on 18–20 March 2012. Comprehensive ground-based observations and satellite retrievals were used to estimate aerosol optical properties, validate calculations and carry out radiation closure. The broadband surface albedo, fluxes at the bottom and top of the atmosphere as well as instantaneous dust radiative forcing were estimated both from the model and observations. Diurnal cycle of the shortwave instantaneous dust direct radiative forcing was studied for a range of aerosol and surface characteristics representative of the Arabian Peninsula. Mechanisms and parameters responsible for diurnal variability of the radiative forcing were evaluated. We found that intrinsic variability of the surface albedo and its dependence on atmospheric conditions, along with anisotropic aerosol scattering, are mostly responsible for diurnal effects.

Sign in / Sign up

Export Citation Format

Share Document