The sensitivity of CRNS and Sentinel-2 products to detect differences in soil water content along a toposequence with two contrasting parent materials

2021 ◽  
Author(s):  
Leticia Gaspar ◽  
Trenton Franz ◽  
Ivan Lizaga ◽  
Borja Latorre ◽  
Ana Navas
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Parent Material ◽  
Low Permeability ◽  
Parent Materials ◽  
The Us ◽  
Neutron Sensors ◽  
Sentinel 2

<p>Soil moisture controls hydrological processes in natural and agricultural systems. A clear understanding of their temporal dynamics and spatial variability is essential to control soil degradation processes, irrigation management and water use efficiency. In recent years, the measurement of soil water content (SWC) with ground-based neutron sensors and remote sensing products have become promising non-invasive methods for different spatial scales. In this study, we are investigating the sensitivity of using cosmic ray neutron sensor (CRNS) and Sentinel-2 SWC index for quantifying different dynamics of soil moisture along a toposequence with underlying contrasting parent materials. For this study, three sites were selected in the upper section (US) soils on limestones correspond to Muschelkalk facies, and another three in the lower section (LS) siliciclastic materials composed of low-permeability marls and claystone formation with primarily silty clay texture (Keuper facies). During two surveys, which correspond to wet (spring 2018/05/05) and dry conditions (summer 2018/08/05), a set of soil moisture data were obtained by using i) portable CRNS backpack, ii) satellite-based information and iii) HS200 sensor Delta-T Devices. The physical composition of the studied soils reflects the clear difference in parent material, with mean content of soil organic carbon of 6% in US against 1% in LW, while the mean clay content was lower in US (21%) than in LS (26%). The infiltration measurements also show different responses for water infiltration capacity, with a much higher mean value of hydraulic conductivity for the soils in the US (317 mm per day), reflecting the karst features, than in the LS (35 mm per day) corresponding to the siliciclastic materials. Our results show similar trends during the two surveys, obtaining significantly lower soil water content on limestones at the US where infiltration processes prevailed thus facilitating leaching and limiting runoff. In contrast, the higher soil water content was on siliciclastic soils at the LS where the low permeability of soils due to the clayed substrate promoted increased runoff. Focusing on the comparison of soil moisture data obtained during the wet and dry surveys, a soil characteristic dependency is observed, with a more different soil moisture state on siliciclastic soils (LS) between the two surveys than for the soils on limestones. Our preliminary results pinpoint that CRNS, Sentinel-2 index and field data captured soil moisture dynamics along the toposequence and demonstrated the sensitivity of neutron sensors and remote sensing products to investigate the effect of parent material on soil water content at sampling scale.</p>

scholarly journals Use of cosmic ray neutron sensors for soil moisture monitoring in forests

2015 ◽  
Vol 12 (9) ◽  
pp. 9813-9864 ◽  
Author(s):  
I. Heidbüchel ◽  
A. Güntner ◽  
T. Blume
Keyword(s):  
Time Series ◽  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Cosmic Ray ◽  
Soil Samples ◽  
Calibration Function ◽  
Neutron Sensors ◽  
Hydrogen Mass

Abstract. Cosmic ray neutron sensors (CRS) are a promising technique to measure soil moisture at intermediate scales. To convert neutron counts to average volumetric soil water content a simple calibration function can be used (the N0-calibration of Desilets et al., 2010). This calibration function is based on soil water content derived directly from soil samples taken within the footprint of the sensor. We installed a CRS in a mixed forest in the lowlands of north-eastern Germany and calibrated it 10 times throughout one calendar year. Each calibration with the N0-calibration function resulted in a different CRS soil moisture time series, with deviations of up to 0.12 m3 m-3 for individual values of soil water content. Also, many of the calibration efforts resulted in time series that could not be matched with independent in situ measurements of soil water content. We therefore suggest a new calibration function with a different shape that can vary from one location to another. A two-point calibration proved to be adequate to correctly define the shape of the new calibration function if the calibration points were taken during both dry and wet conditions covering at least 50 % of the total range of soil moisture. The best results were obtained when the soil samples used for calibration were linearly weighted as a function of depth in the soil profile and non-linearly weighted as a function of distance from the CRS, and when the depth-specific amount of soil organic matter and lattice water content was explicitly considered. The annual cycle of tree foliation was found to be a negligible factor for calibration because the variable hydrogen mass in the leaves was small compared to the hydrogen mass changes by soil moisture variations. Finally, we provide a best practice calibration guide for CRS in forested environments.

scholarly journals Relating surface backscatter response from TRMM Precipitation Radar to soil moisture: results over a semi-arid region

2009 ◽  
Vol 6 (5) ◽  
pp. 6425-6454
Author(s):  
H. Stephen ◽  
S. Ahmad ◽  
T. C. Piechota ◽  
C. Tang
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Arid Regions ◽  
Vegetation Index ◽  
Temporal Trends ◽  
Model Parameters ◽  
Precipitation Radar ◽  
Semi Arid

Abstract. The Tropical Rainfall Measuring Mission (TRMM) carries aboard the Precipitation Radar (TRMMPR) that measures the backscatter (σ°) of the surface. σ° is sensitive to surface soil moisture and vegetation conditions. Due to sparse vegetation in arid and semi-arid regions, TRMMPR σ° primarily depends on the soil water content. In this study we relate TRMMPR σ° measurements to soil water content (ms) in Lower Colorado River Basin (LCRB). σ° dependence on ms is studied for different vegetation greenness values determined through Normalized Difference Vegetation Index (NDVI). A new model of σ° that couples incidence angle, ms, and NDVI is used to derive parameters and retrieve soil water content. The calibration and validation of this model are performed using simulated and measured ms data. Simulated ms is estimated using Variable Infiltration Capacity (VIC) model whereas measured ms is acquired from ground measuring stations in Walnut Gulch Experimental Watershed (WGEW). σ° model is calibrated using VIC and WGEW ms data during 1998 and the calibrated model is used to derive ms during later years. The temporal trends of derived ms are consistent with VIC and WGEW ms data with correlation coefficient (R) of 0.89 and 0.74, respectively. Derived ms is also consistent with the measured precipitation data with R=0.76. The gridded VIC data is used to calibrate the model at each grid point in LCRB and spatial maps of the model parameters are prepared. The model parameters are spatially coherent with the general regional topography in LCRB. TRMMPR σ° derived soil moisture maps during May (dry) and August (wet) 1999 are spatially similar to VIC estimates with correlation 0.67 and 0.76, respectively. This research provides new insights into Ku-band σ° dependence on soil water content in the arid regions.

Root effects on soil water and hydraulic properties

Biologia ◽  
2007 ◽  
Vol 62 (5) ◽  
Author(s):  
Horst Gerke ◽  
Rolf Kuchenbuch
Keyword(s):  
Soil Moisture ◽  
Moisture Content ◽  
Water Content ◽  
Bulk Density ◽  
Soil Water ◽  
Soil Water Content ◽  
Hydraulic Properties ◽  
Soil Hydraulic Properties ◽  
Soil Hydraulic ◽  
Root Effects

AbstractPlants can affect soil moisture and the soil hydraulic properties both directly by root water uptake and indirectly by modifying the soil structure. Furthermore, water in plant roots is mostly neglected when studying soil hydraulic properties. In this contribution, we analyze effects of the moisture content inside roots as compared to bulk soil moisture contents and speculate on implications of non-capillary-bound root water for determination of soil moisture and calibration of soil hydraulic properties.In a field crop of maize (Zea mays) of 75 cm row spacing, we sampled the total soil volumes of 0.7 m × 0.4 m and 0.3 m deep plots at the time of tasseling. For each of the 84 soil cubes of 10 cm edge length, root mass and length as well as moisture content and soil bulk density were determined. Roots were separated in 3 size classes for which a mean root porosity of 0.82 was obtained from the relation between root dry mass density and root bulk density using pycnometers. The spatially distributed fractions of root water contents were compared with those of the water in capillary pores of the soil matrix.Water inside roots was mostly below 2–5% of total soil water content; however, locally near the plant rows it was up to 20%. The results suggest that soil moisture in roots should be separately considered. Upon drying, the relation between the soil and root water may change towards water remaining in roots. Relations depend especially on soil water retention properties, growth stages, and root distributions. Gravimetric soil water content measurement could be misleading and TDR probes providing an integrated signal are difficult to interpret. Root effects should be more intensively studied for improved field soil water balance calculations.

Effect of water on common lambsquarters (Chenopodium album L.) and barnyardgrass [Echinochloa crus-galli (L.) Beauv.] seedling emergence in corn

2002 ◽  
Vol 82 (4) ◽  
pp. 855-859 ◽  
Author(s):  
M. L. Leblanc ◽  
D. C. Cloutier ◽  
C. Hamel
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Chenopodium Album ◽  
Seedling Emergence ◽  
Field Capacity ◽  
Emergence Period ◽  
Common Lambsquarters ◽  
Weed Emergence

A 2-year field study was conducted in corn to determine the influence of rainfall, irrigation and soil water content on common lambsquarters and barnyardgrass emergence. Rainfall or irrigation had no influence on the final weed density and little on the pattern of weed emergence because the soil water content was at or greater than field capacity during the main weed emergence period. Irrigation may hasten the first weed emergence by warming the soil when temperature is limiting for germination. In southwestern Quebec, temperature appears to be the most important factor regulating germination in the spring since soil moisture is normally at field capacity for a long period, in part because of the melting of snow. Key words: Irrigation, weed emergence, soil moisture

scholarly journals On the scaling characteristics of observed and simulated spatial soil moisture fields

2009 ◽  
Vol 16 (1) ◽  
pp. 141-150 ◽  
Author(s):  
M. Gebremichael ◽  
R. Rigon ◽  
G. Bertoldi ◽  
T. M. Over
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Spatial Correlation ◽  
Hydrologic Model ◽  
Invariance Property ◽  
Spatial Average ◽  
Hydrologic Models ◽  
Model Simulations

Abstract. By providing continuous high-resolution simulations of soil moisture fields, distributed hydrologic models could be powerful tools to advance the scientific community's understanding of the space-time variability and scaling characteristics of soil moisture fields. However, in order to use the soil moisture simulations from hydrologic models with confidence, it is important to understand whether the models are able to represent in a reliable way the processes regulating soil moisture variability. In this study, a comparison of the scaling characteristics of spatial soil moisture fields derived from a set of microwave radiometer observations from the Southern Great Plains 1997 experiment and corresponding simulations using the distributed hydrologic model GEOtop is performed through the use of generalized variograms. Microwave observations and model simulations are in agreement with respect to suggesting the existence of a scale-invariance property in the variograms of spatial soil moisture fields, and indicating that the scaling characteristics vary with changes in the spatial average soil water content. However, observations and simulations give contradictory results regarding the relationship between the scaling parameters (i.e. spatial organization) and average soil water content. The drying process increased the spatial correlation of the microwave observations at both short and long separation distances while increasing the rate of decay of correlation with distance. The effect of drying on the spatial correlation of the model simulations was more complex, depending on the storm and the simulation examined, but for the largest storm in the simulation most similar to the observations, drying increased the long-range correlation but decreased the short-range. This is an indication that model simulations, while reproducing correctly the total streamflow at the outlet of the watershed, may not accurately reproduce the runoff production mechanisms. Consideration of the scaling characteristics of spatial soil moisture fields can therefore serve as a more intensive means for validating distributed hydrologic models, compared to the traditional approach of only comparing the streamflow hydrographs.

scholarly journals Rainfall Intensification Enhances Deep Percolation and Soil Water Content in Tilled and No-Till Cropping Systems of the US Midwest

2018 ◽  
Vol 17 (1) ◽  
pp. 180128 ◽  
Author(s):  
Laura J.T. Hess ◽  
Eve-Lyn S. Hinckley ◽  
G. Philip Robertson ◽  
Stephen K. Hamilton ◽  
Pamela A. Matson
Keyword(s):  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Cropping Systems ◽  
Deep Percolation ◽  
No Till ◽  
The Us ◽  
Us Midwest

scholarly journals Enhancing Soil Water Content for Increased Food Production in Semi-Arid Areas of Kenya Results From an On-Farm Trial in Mwala District, Kenya

2014 ◽  
Vol 6 (4) ◽  
pp. 125 ◽  
Author(s):  
Anne Karuma ◽  
Peter Mtakwa ◽  
Nyambilila Amuri ◽  
Charles K. Gachene ◽  
Patrick Gicheru
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Water Conservation ◽  
Crop Yields ◽  
Conservation Tillage ◽  
Cropping Systems ◽  
Soil Conditions ◽  
Tillage Methods

Soil water conservation through tillage is one of the appropriate ways of addressing soil moisture deficit in rainfed agriculture. This study evaluated the effects of tillage practices on soil moisture conservation and crop yields in Mwala District, Eastern Kenya during the long rains (LR) and short rains (SR) of 2012/13. Six tillage systems: Disc plough (MB), Disc plough and harrowing (MBH), Ox-ploughing (OX), Subsoiling – ripping (SR), Hand hoe and Tied Ridges (HTR) and Hand hoe only (H) and, three cropping systems namely, sole maize, sole bean and maize - bean intercrop, were investigated in a split-plot design with four replicates. Data on soil water content was monitored at different weeks after planting and the crop yields at end of each growing season. A three-season average shows that soil water content and crop yields were higher in conventional tillage methods compared to the conservation tillage methods. Long term tillage experiments are thus required at different locations, under various environmental and soil conditions to validate the study findings.

scholarly journals Soil Structure and Texture Effects on the Precision of Soil Water Content Measurements with a Capacitance- Based Electromagnetic Sensor

2020 ◽  
Vol 63 (1) ◽  
pp. 141-152
Author(s):  
Jasreman Singh ◽  
Derek M. Heeren ◽  
Daran R. Rudnick ◽  
Wayne E. Woldt ◽  
Geng Bai ◽  
...  
Keyword(s):  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Sensor Calibration ◽  
Soil Water Depletion ◽  
Undisturbed Soil ◽  
Water Depletion ◽  
Soil Moisture Sensors ◽  
Electromagnetic Sensor

HighlightsCapacitance-based electromagnetic soil moisture sensors were tested in disturbed and undisturbed soils.The uncertainty in estimation of soil water depth was lower using the undisturbed soil sample calibrations.The uncertainty in estimation of soil water depletion was lower than the uncertainty in volumetric water content.Undisturbed calibration of water depletion quantifies water demand with better precision and avoids over-watering.Abstract. The physical properties of soil, such as structure and texture, can affect the performance of an electromagnetic sensor in measuring soil water content. Historically, calibrations have been performed on repacked samples in the laboratory and on soils in the field, but little research has been done on laboratory calibrations with intact (undisturbed) soil cores. In this study, three replications each of disturbed and undisturbed soil samples were collected from two soil texture classes (Yutan silty clay loam and Fillmore silt loam) at a field site in eastern Nebraska to investigate the effects of soil structure and texture on the precision of a METER Group GS-1 capacitance-based sensor calibration. In addition, GS-1 sensors were installed in the field near the soil collection sites at three depths (0.15, 0.46, and 0.76 m). The soil moisture sensor had higher precision in the undisturbed laboratory setup, as the undisturbed calibration had a better correlation [slope closer to one, R2undisturbed (0.89) > R2disturbed (0.73)] than the disturbed calibrations for the Yutan and Fillmore texture classes, and the root mean square difference using the laboratory calibration (RMSDL) was higher for pooled disturbed samples (0.053 m3 m-3) in comparison to pooled undisturbed samples (0.023 m3 m-3). The uncertainty in determination of volumetric water content (?v) was higher using the factory calibration (RMSDF) in comparison to the laboratory calibration (RMSDL) for the different soil structures and texture classes. In general, the uncertainty in estimation of soil water depth was greater than the uncertainty in estimation of soil water depletion by the sensors installed in the field, and the uncertainties in estimation of depth and depletion were lower using the calibration developed from the undisturbed soil samples. The undisturbed calibration of soil water depletion would determine water demand with better precision and potentially avoid over-watering, offering relief from water shortages. Further investigation of sensor calibration techniques is required to enhance the applicability of soil moisture sensors for efficient irrigation management. Keywords: Calibration, Capacitance, Depletion, Irrigation, Precision, Sensor, Soil water content, Structure, Uncertainty.

scholarly journals Application of Ground-Penetrating Radar and a Combined Penetrometer–Moisture Probe for Evaluating Spatial Distribution of Soil Moisture and Soil Hardness in Coastal and Inland Windbreaks

Geosciences ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 238
Author(s):  
Kenta Iwasaki ◽  
Makoto Tamura ◽  
Hirokazu Sato ◽  
Kazuhiko Masaka ◽  
Daisuke Oka ◽  
...  
Keyword(s):  
Spatial Distribution ◽  
Soil Moisture ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Ground Penetrating Radar ◽  
Soil Compaction ◽  
Soil Moisture Condition ◽  
Soil Hardness ◽  
Ground Penetrating

The development of a method to easily investigate the spatial distribution of soil moisture and soil hardness in tree windbreaks is necessary because these windbreaks often decline due to inappropriate soil moisture condition and soil compaction. This research examined the applicability of ground-penetrating radar (GPR) and a combined penetrometer–moisture probe (CPMP) for evaluating the spatial distribution of soil moisture and soil hardness in four windbreaks with different soil characteristics. A GPR-reflecting interface was observed at a less permeable layer in a coastal windbreak and at a depth affected by soil compaction in an inland windbreak with andosol. The spatial distribution of the groundwater table could also be evaluated by examining the attenuation of GPR reflection in a coastal windbreak. In contrast, GPR was not applicable in an inland windbreak with peat because of high soil water content near the soil surface. The CPMP could detect vertical distributions of soil hardness and soil water content regardless of soil type. The CPMP was useful for interpreting GPR profiles, and GPR was useful for interpolating the information about the horizontal distribution of soil moisture and soil hardness between survey points made with the CPMP. Thus, the combination of GPR and a CPMP is ideal for examining the two-dimensional spatial distribution of soil moisture and soil hardness at windbreaks with soils for which both methods are applicable.

Hydrologic soil properties and application of a soil moisture model in a balsam fir forest

1988 ◽  
Vol 18 (4) ◽  
pp. 427-434 ◽  
Author(s):  
Richard Barry ◽  
André P. Plamondon ◽  
Jean Stein
Keyword(s):  
Soil Moisture ◽  
Soil Properties ◽  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Crop Coefficient ◽  
Balsam Fir ◽  
Physical Parameters ◽  
Volumetric Soil Water Content ◽  
Soil Moisture Model

An analysis of hydrologic soil properties and the prediction of volumetric soil water content during four summers have been done for a site located in the balsam fir (Abiesbalsamea (L.) Mill.) forest of the Lac Laflamme watershed. The hydrologic properties were used to identify three different soil layers, THIRSTY, a soil moisture model using the Penman evapotranspiration formula, was applied to predict daily volumetric water content of these layers. Predictions of soil moisture with the calibrated model were close to the observed data for the median layer (20–60 cm from the soil surface) and less accurate for the surface layer (0–20 cm) where important transpiration activities take place. The model appeared unreliable for predicting soil water content of the bottom layer (60–100 cm) which was often saturated by groundwater. The calibration of the model required modifications of the observed values of the available water content at field capacity and the relative root density factor and was adjusted with the crop coefficient of the Penman evapotranspiration formula. These modifications of observed physical parameters raise the question of the feasibility of extrapolating the model to other sites without extensive calibration. The high sensitivity to variations of the crop coefficient applied to the evapotranspiration equation indicated that a more physically based transpiration model, supported by field-oriented process studies, would be required to improve the model's performance.

Sign in / Sign up

Export Citation Format

Share Document