scholarly journals Required sampling density of ground-based soil moisture and brightness temperature observations for calibration and validation of L-band satellite observations based on a virtual reality

2020 ◽  
Vol 24 (4) ◽  
pp. 1957-1973
Author(s):  
Shaoning Lv ◽  
Bernd Schalge ◽  
Pablo Saavedra Garfias ◽  
Clemens Simmer
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
Brightness Temperature ◽  
Confidence Level ◽  
Land Surface ◽  
System Modeling ◽  
Microwave Remote Sensing ◽  
Microwave Emission ◽  
Near Surface ◽  
Sampling Distance

Abstract. Microwave remote sensing is the most promising tool for monitoring near-surface soil moisture distributions globally. With the Soil Moisture and Ocean Salinity (SMOS) and Soil Moisture Active Passive (SMAP) missions in orbit, considerable efforts are being made to evaluate derived soil moisture products via ground observations, microwave transfer simulation, and independent remote sensing retrievals. Due to the large footprint of the satellite radiometers of about 40 km in diameter and the spatial heterogeneity of soil moisture, minimum sampling densities for soil moisture are required to challenge the targeted precision. Here we use 400 m resolution simulations with the regional Terrestrial System Modeling Platform (TerrSysMP) and its coupling with the Community Microwave Emission Modelling platform (CMEM) to quantify the maximum sampling distance allowed for soil moisture and brightness temperature validation. Our analysis suggests that an overall sampling distance of finer than 6 km is required to validate the targeted accuracy of 0.04 cm3 cm−3 with a 70 % confidence level in SMOS and SMAP estimates over typical mid-latitude European regions. The maximum allowed sampling distance depends on the land-surface heterogeneity and the meteorological situation, which influences the soil moisture patterns, and ranges from about 6 to 17 km for a 70 % confidence level for a typical year. At the maximum allowed sampling distance on a 70 % confidence level, the accuracy of footprint-averaged soil moisture is equal to or better than brightness temperature estimates over the same area. Estimates strongly deteriorate with larger sampling distances. For the evaluation of the smaller footprints of the active and active–passive products of SMAP the required sampling densities increase; e.g., when a grid resolution of 3 km diameter is sampled by three sites of footprints of 9 km sampled by five sites required, only 50 %–60 % of the pixels have a sampling error below the nominal values. The required minimum sampling densities for ground-based radiometer networks to estimate footprint-averaged brightness temperature are higher than for soil moisture due to the non-linearities of radiative transfer, and only weakly correlated in space and time. This study provides a basis for a better understanding of the sometimes strong mismatches between derived satellite soil moisture products and ground-based measurements.

scholarly journals Required sampling-density of ground-based soil moisture and brightness temperature observations for calibration/validation of L-band satellite observations based on a virtual reality

2019 ◽  
Author(s):  
Shaoning Lv ◽  
Bernd Schalge ◽  
Pablo Saavedra Garfias ◽  
Clemens Simmer
Keyword(s):  
Soil Moisture ◽  
Brightness Temperature ◽  
Confidence Level ◽  
Land Surface ◽  
Microwave Remote Sensing ◽  
Global Scale ◽  
Microwave Emission ◽  
Near Surface ◽  
Temperature Observations ◽  
Better Than

Abstract. Microwave remote sensing is the most promising tool for monitoring global-scale near-surface soil moisture distributions. With the Soil Moisture and Ocean Salinity (SMOS) and Soil Moisture Active Passive (SMAP) missions in orbit, considerable efforts are made to evaluate their soil moisture products via ground observations, forward microwave transfer simulation, and retrievals. Due to the large footprint of the satellite radiometers of about 40 km in diameter and the spatial heterogeneity of soil moisture, minimum sampling densities for soil moisture are required to challenge the targeted precision. Here we use 400 m resolution simulations with the regional terrestrial system model TerrSysMP and its coupling with the Community Microwave Emission Modelling platform (CMEM) to quantify sampling distance required for soil moisture and brightness temperature validation. Our analysis suggests that an overall sampling resolution of better than 6 km is required to validate the targeted accuracy of 0.04 cm3/cm3 (70 % confidence level) in SMOS and SMAP over typical midlatitude European regions. The minimum sampling resolution depends on the land-surface inhomogeneity and the meteorological situation, which influence the soil moisture patterns, and ranges from about 7 km to 17 km for a 70 % confidence level for a typical year. At the minimum sampling resolution for a 70 % confidence level also the accuracy of footprint-averaged brightness temperature estimates is equal or better than 15 K/10 K for H/V polarization. Estimates strongly deteriorate with sparser sampling densities, e.g., at 3/9 km with 3/5 sampling sites the confidence level of derived footprint estimates can reach about 0.5–0.6 for soil moisture which is much less than the standard 0.7 requirements for ground measurements. The representativeness of ground-based soil moisture and brightness temperature observations – and thus their required minimum sampling densities – are only weakly correlated in space and time. This study provides a basis for a better understanding of sometimes strong mismatches between derived satellite soil moisture products and ground-based measurements.

scholarly journals Towards an integrated soil moisture drought monitor for East Africa

2012 ◽  
Vol 9 (4) ◽  
pp. 4587-4631 ◽  
Author(s):  
W. B. Anderson ◽  
B. F. Zaitchik ◽  
C. R. Hain ◽  
M. C. Anderson ◽  
M. T. Yilmaz ◽  
...  
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
East Africa ◽  
Remote Monitoring ◽  
Vegetation Cover ◽  
Land Surface ◽  
Microwave Remote Sensing ◽  
Surface Model ◽  
Monitoring Methods ◽  
Data Scarcity

Abstract. Drought in East Africa is a recurring phenomenon with significant humanitarian impacts. Given the steep climatic gradients, topographic contrasts, general data scarcity, and, in places, political instability that characterize the region, there is a need for spatially distributed, remotely derived monitoring systems to inform national and international drought response. At the same time, the very diversity and data scarcity that necessitate remote monitoring also make it difficult to evaluate the reliability of these systems. Here we apply a suite of remote monitoring techniques to characterize the temporal and spatial evolution of the 2010–2011 Horn of Africa drought. Diverse satellite observations allow for evaluation of meteorological, agricultural, and hydrological aspects of drought, each of which is of interest to different stakeholders. Focusing on soil moisture, we apply triple collocation analysis (TCA) to three independent methods for estimating soil moisture anomalies to characterize relative error between products and to provide a basis for objective data merging. The three soil moisture methods evaluated include microwave remote sensing using the Advanced Microwave Scanning Radiometer – Earth Observing System (AMSR-E) sensor, thermal remote sensing using the Atmosphere-Land Exchange Inverse (ALEXI) surface energy balance algorithm, and physically-based land surface modeling using the Noah land surface model. It was found that the three soil moisture monitoring methods yield similar drought anomaly estimates in areas characterized by extremely low or by moderate vegetation cover, particularly during the below-average 2011 long rainy season. Systematic discrepancies were found, however, in regions of moderately low vegetation cover and high vegetation cover, especially during the failed 2010 short rains. The merged, TCA-weighted soil moisture composite product takes advantage of the relative strengths of each method, as judged by the consistency of anomaly estimates across independent methods. This approach holds potential as a remote soil moisture-based drought monitoring system that is robust across the diverse climatic and ecological zones of East Africa.

Characterising recent drought events using current reanalysis and remote-sensing soil moisture products within a common framework

2021 ◽  
Author(s):  
Martin Hirschi ◽  
Bas Crezee ◽  
Sonia I. Seneviratne
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
Land Surface ◽  
Root Zone ◽  
Microwave Remote Sensing ◽  
Agricultural Drought ◽  
Climate Data ◽  
Data Store ◽  
Common Framework ◽  
Long Term Trends

<p>Drought events cause multiple impacts on the environment, the society and the economy. Here, we analyse recent major drought events with different metrics using a common framework. The analysis is based on current reanalysis (ERA5, ERA5-Land, MERRA-2) and merged remote-sensing products (ESA-CCI soil moisture, gridded satellite soil moisture from the Copernicus Climate Data Store), focusing on soil moisture (or agricultural) drought. The events are characterised by their severity, magnitude, duration and spatial extent, which are calculated from standardised daily anomalies of surface and root-zone soil moisture. We investigate the ability of the different products to represent the droughts and set the different events in context to each other. The considered products also offer opportunities for drought monitoring since they are available in near-real time.</p><p>All investigated products are able to represent the investigated drought events. Overall, ERA5 and ERA5-Land often show the strongest, and the remote-sensing products often weaker responses based on surface soil moisture. The weaker severities of the events in the remote-sensing products are both related to shorter event durations as well as less pronounced average negative standardised soil moisture anomalies, while the magnitudes (i.e., the minimum of the standardised anomalies over time) are comparable to the reanalysis products. Differing global distributions of long-term trends may explain some differences in the drought responses of the products. Also, the lower penetration depth of microwave remote sensing compared to the top layer of the involved land surface models could explain the partly weaker negative standardized soil moisture anomalies in the remote-sensing products during the investigated events. In the root zone (based on the reanalysis products), the drought events often show prolonged durations, but weaker magnitudes and smaller spatial extents.</p>

scholarly journals Earth Observations-Based Evapotranspiration in Northeastern Thailand

2019 ◽  
Vol 11 (2) ◽  
pp. 138 ◽  
Author(s):  
Chaolei Zheng ◽  
Li Jia ◽  
Guangcheng Hu ◽  
Jing Lu
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
Surface Temperature ◽  
Land Surface Temperature ◽  
Land Surface ◽  
Microwave Remote Sensing ◽  
Spatiotemporal Pattern ◽  
Monsoon Climate ◽  
Thermal Remote Sensing ◽  
Clear Sky

Thailand is characterized by typical tropical monsoon climate, and is suffering serious water related problems, including seasonal drought and flooding. These issues are highly related to the hydrological processes, e.g., precipitation and evapotranspiration (ET), which are helpful to understand and cope with these problems. It is critical to study the spatiotemporal pattern of ET in Thailand to support the local water resource management. In the current study, daily ET was estimated over Thailand by ETMonitor, a process-based model, with mainly satellite earth observation datasets as input. One major advantage of the ETMonitor algorithm is that it introduces the impact of soil moisture on ET by assimilating the surface soil moisture from microwave remote sensing, and it reduces the dependence on land surface temperature, as the thermal remote sensing is highly sensitive to cloud, which limits the ability to achieve spatial and temporal continuity of daily ET. The ETMonitor algorithm was further improved in current study to take advantage of thermal remote sensing. In the improved scheme, the evaporation fraction was first obtained by land surface temperature—vegetation index triangle method, which was used to estimate ET in the clear days. The soil moisture stress index (SMSI) was defined to express the constrain of soil moisture on ET, and clear sky SMSI was retrieved according to the estimated clear sky ET. Clear sky SMSI was then interpolated to cloudy days to obtain the SMSI for all sky conditions. Finally, time-series ET at daily resolution was achieved using the interpolated spatio-temporal continuous SMSI. Good agreements were found between the estimated daily ET and flux tower observations with root mean square error ranging between 1.08 and 1.58 mm d−1, which showed better accuracy than the ET product from MODerate resolution Imaging Spectroradiometer (MODIS), especially for the forest sites. Chi and Mun river basins, located in Northeast Thailand, were selected to analyze the spatial pattern of ET. The results indicate that the ET had large fluctuation in seasonal variation, which is predominantly impacted by the monsoon climate.

scholarly journals A bare ground evaporation revision in the ECMWF land-surface scheme: evaluation of its impact using ground soil moisture and satellite microwave data

2012 ◽  
Vol 16 (10) ◽  
pp. 3607-3620 ◽  
Author(s):  
C. Albergel ◽  
G. Balsamo ◽  
P. de Rosnay ◽  
J. Muñoz-Sabater ◽  
S. Boussetta
Keyword(s):  
Soil Moisture ◽  
Brightness Temperature ◽  
Land Surface ◽  
The United States ◽  
Microwave Emission ◽  
Bare Ground ◽  
New Formulation ◽  
The Impact ◽  
Surface Fields

Abstract. In situ soil moisture data from 122 stations across the United States are used to evaluate the impact of a new bare ground evaporation formulation at ECMWF. In November 2010, the bare ground evaporation used in ECMWF's operational Integrated Forecasting System (IFS) was enhanced by adopting a lower stress threshold than for the vegetation, allowing a higher evaporation. It results in more realistic soil moisture values when compared to in situ data, particularly over dry areas. Use was made of the operational IFS and offline experiments for the evaluation. The latter are based on a fixed version of the IFS and make it possible to assess the impact of a single modification, while the operational analysis is based on a continuous effort to improve the analysis and modelling systems, resulting in frequent updates (a few times a year). Considering the field sites with a fraction of bare ground greater than 0.2, the root mean square difference (RMSD) of soil moisture is shown to decrease from 0.118 m3 m−3 to 0.087 m3 m−3 when using the new formulation in offline experiments, and from 0.110 m3 m−3 to 0.088 m3 m−3 in operations. It also improves correlations. Additionally, the impact of the new formulation on the terrestrial microwave emission at a global scale is investigated. Realistic and dynamically consistent fields of brightness temperature as a function of the land surface conditions are required for the assimilation of the SMOS data. Brightness temperature simulated from surface fields from two offline experiments with the Community Microwave Emission Modelling (CMEM) platform present monthly mean differences up to 7 K. Offline experiments with the new formulation present drier soil moisture, hence simulated brightness temperature with its surface fields are larger. They are also closer to SMOS remotely sensed brightness temperature.

scholarly journals Advances in Quantitative Earth Remote Sensing: Past, Present and Future

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5399 ◽  
Author(s):  
Ghassem R. Asrar
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
Surface Temperature ◽  
Land Surface Temperature ◽  
Land Surface ◽  
Microwave Remote Sensing ◽  
Polar Regions ◽  
Earth System ◽  
Earth Remote Sensing ◽  
Earth’S System

A combination of multispectral visible, infra-red and microwave sensors on the constellation of international Earth-observing satellites are providing unprecedented observations for all Earth domains over multiple decades (i.e., atmosphere, land, oceans and polar regions). This Special Issue of Sensors is dedicated to papers that describe such advances in the field of Earth remote sensing and their applications to advance understanding of Earth’s planetary system and applying the resulting knowledge and information to meet the societal needs during recent decades. The papers accepted and published in this issue convey the exciting scientific and technical challenges and opportunities for remote sensing of all domains of Earth system, including terrestrial, aquatic and coastal ecosystems; bathymetry of coasts and islands; oceans and lakes; measurement of soil moisture and land surface temperature that affects both water resources and food production; and advances in use of sun-induced fluorescence (SIF) in measuring and monitoring the contribution of terrestrial vegetation in the cycling of carbon in Earth’s system. Measurements of SIF, for example, has had a profound impact on the field of terrestrial ecosystems research and modelling. The Earth Polychromatic Imaging Camera (EPIC) instrument on the Deep Space Climate Observatory (DSCVR) satellite located at the Sun–Earth Lagrange Point One, about 1.5 million miles away from Earth, is providing unique observations of the Earth’s full sun-lit disk from pole-to-pole and minute-by-minute, which overcomes a major limitation in temporal coverage of Earth by other polar-orbiting Earth-observing satellites. Active and passive microwave remote sensing instruments allow all-weather measurements and monitoring of clouds, weather phenomena, land-surface temperature and soil moisture by overcoming the presence of clouds that affect measurements by visible and infrared sensors. The use of powerful in-space lasers is allowing scientists and engineers to measure and monitor rapidly changing ice sheets in polar regions and mountain glaciers. These sensors and their measurements that are deployed on major space-based observatories and small- and micro-satellites, and the scientific knowledge they provide, are enhancing our understanding of planet Earth and development of Earth system models that are used increasingly to project future conditions due to Earth’s rapidly changing environmental conditions. Such knowledge and information are benefiting people, businesses and governments worldwide.

Evaluation of Assumptions in Soil Moisture Triple Collocation Analysis

2014 ◽  
Vol 15 (3) ◽  
pp. 1293-1302 ◽  
Author(s):  
M. Tugrul Yilmaz ◽  
Wade T. Crow
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
Land Surface ◽  
Land Surface Model ◽  
Microwave Remote Sensing ◽  
Surface Model ◽  
Correlated Errors ◽  
Cross Covariance ◽  
Mutual Independence ◽  
The Impact

Abstract Triple collocation analysis (TCA) enables estimation of error variances for three or more products that retrieve or estimate the same geophysical variable using mutually independent methods. Several statistical assumptions regarding the statistical nature of errors (e.g., mutual independence and orthogonality with respect to the truth) are required for TCA estimates to be unbiased. Even though soil moisture studies commonly acknowledge that these assumptions are required for an unbiased TCA, no study has specifically investigated the degree to which errors in existing soil moisture datasets conform to these assumptions. Here these assumptions are evaluated both analytically and numerically over four extensively instrumented watershed sites using soil moisture products derived from active microwave remote sensing, passive microwave remote sensing, and a land surface model. Results demonstrate that nonorthogonal and error cross-covariance terms represent a significant fraction of the total variance of these products. However, the overall impact of error cross correlation on TCA is found to be significantly larger than the impact of nonorthogonal errors. Because of the impact of cross-correlated errors, TCA error estimates generally underestimate the true random error of soil moisture products.

Experimental Study of C Band Passive Microwave Remote Sensing of Soil Moisture

2013 ◽  
Vol 477-478 ◽  
pp. 624-627
Author(s):  
Xiao Liu Gao ◽  
Hui Hui Zhang
Keyword(s):  
Remote Sensing ◽  
Soil Moisture ◽  
Emission Rate ◽  
Soil Surface ◽  
Microwave Remote Sensing ◽  
Passive Microwave ◽  
Microwave Emission ◽  
Passive Microwave Remote Sensing ◽  
Soil Surface Roughness ◽  
Relationship Of

Passive microwave remote sensing is one of the most effective methods for inversing soil moisture. Under the condition of laboratory, firstly, C band microwave radiation was used to achieve the trial of ground-based remote sensing soil moisture, and then regression analysis was carried out according to the data measured, finally, got the C band experience regression model of soil moisture inversion. The results showed that: in the level-off state of soil surface, soil humidity and soil microwave emission rate is linear negative correlation, in the other words, soil microwave emission rate decreased while the soil moisture increased. Besides, with the increasing of soil surface roughness, both the value of microwave polarization index (MPDI) and microwave emission rate polarization difference Δe have the same trend of quick drop, stabilization and slow raise, and it presented the relationship of quadratic curve with the change of roughness.

scholarly journals Application of satellite microwave remote sensed brightness temperature in the regional soil moisture simulation

2009 ◽  
Vol 6 (1) ◽  
pp. 1233-1260 ◽  
Author(s):  
X. K. Shi ◽  
J. Wen ◽  
L. Wang ◽  
T. T. Zhang ◽  
H. Tian ◽  
...  
Keyword(s):  
Soil Moisture ◽  
Brightness Temperature ◽  
Land Surface ◽  
Surface Soil ◽  
Microwave Remote Sensing ◽  
Temperature Data ◽  
Fine Tuning ◽  
Tibet Plateau ◽  
Surface Model ◽  
Satellite Microwave

Abstract. As the satellite microwave remote sensed brightness temperature is sensitive to land surface soil moisture (SM) and SM is a basic output variable in model simulation, it is of great significance to use the brightness temperature data to improve SM numerical simulation. In this paper, the theory developed by Yan et al. (2004) about the relationship between satellite microwave remote sensing polarization index and SM was used to estimate the land surface SM from AMSR-E (Advanced Microwave Scanning Radiometer – Earth Observing System) brightness temperature data. With consideration of land surface soil texture, surface roughness, vegetation optical thickness, and the AMSR-E monthly SM products, the regional daily land surface SM was estimated over the eastern part of the Qinghai-Tibet Plateau. The results show that the estimated SM is lower than the ground measurements and the NCEP (American National Centers for Environmental Prediction) reanalysis data at the Maqu Station (33.85° N, 102.57° E) and the Tanglha Station (33.07° N, 91.94° E), but its regional distribution is reasonable and somewhat better than that from the daily AMSR-E SM product, and its temporal variation shows a quick response to the ground daily precipitations. Furthermore, in order to improve the simulating ability of the WRF (Weather Research and Forecasting) model to land surface SM, the estimated SM was assimilated into the Noah land surface model by the Newtonian relaxation (NR) method. The results indicate that, by fine tuning of the quality factor in NR method, the simulated SM values are improved most in desert area, followed by grassland, shrub and grass mixed zone. At temporal scale, Root Mean Square Error (RMSE) values between simulated and observed SM are decreased 0.03 and 0.07 m3/m3 by using the NR method in the Maqu Station and the Tanglha Station, respectively.

Sign in / Sign up

Export Citation Format

Share Document