scholarly journals Estimation of hazard assessment by FINSIM for west coast and son narmada faults

2018 ◽  
Author(s):  
Shivamanth Angadi ◽  
Mayank Desai
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
West Coast ◽  
Soil Classification ◽  
Earthquake Simulation ◽  
Worst Case ◽  
Site Class ◽  
Class D ◽  
Finite Fault

Abstract. The Seismic hazard study was carried out for Maharashtra state, Bombay (Latitude 18.940 N, Longitude 72.840 E). In the present study the geological fault is known as West coast fault and Son Narmada Faults were studied and used for the earthquake simulation, extended finite fault method originally FINSIM given by M. Atkinson (1998), was used to simulate an earthquake of 6.5 Mw. The soil classification was carried out by the Shear wave velocity and the relation between Shear wave velocity and SPT valves were also recommended by Sumedh Y. Mhaske (2011), since the Mumbai has been formed by the conglomeration of various islands which has come together to form a single landmass. The soil investigation suggested that Most of the region comes under the Class D and C for the worst case simulation we have used the site class D. The peak ground accelerations (PGA) vary from 0.03g to 0.133 g. While coming to zonal area IS1893:2002 still consider the Mumbai city under zone III with the Z value of 0.16 and the result have been compared with the analysis done by many researchers in the same area.

Shear Wave Velocity Investigation for Ten Representative Sites of National Capital Territory, New Delhi, India

2011 ◽  
Vol 2 (1) ◽  
pp. 29-43 ◽  
Author(s):  
A.K. Mahajan ◽  
A.K. Shukla ◽  
Ajit Pandey ◽  
Mukesh Chauhan ◽  
Neetu Chauhan ◽  
...  
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Soft Soil ◽  
River Sediments ◽  
Soil Classification ◽  
New Delhi ◽  
Site Class ◽  
Class B ◽  
Masw Method

In this paper, shear wave velocity (Vs) investigations are carried out using Multichannel analysis of surface waves (MASW) method at ten representative sites in the NCT region, New Delhi. The analysis shows that the Vs obtained from the sites located on Alwar quartzites of Delhi Super Group ranges from 770 m/s to 2800 m/s, whereas on other sites located on lake/river sediments (Nazafgarh, Balsava and Akshar Dham) have Vs less than 180 m/s. The sites located on thick sediments shows Vs of the order of 180 m/s to 250 m/s. According to the soil classification, the sites covered can be classified under three categories: Class ‘B’ (Vs30 as >760m/s; JNU site and Asola site), class ‘D’ (Vs30>180 m/sec-360; Bhavana, Suhalpur, Ghazipur and Kirbi cantt. sites), whereas the sites located near lake/river sediments are classified as class ‘E’ (with very soft soil) and will be prone to liquefaction potential during strong earthquake shaking.

scholarly journals ROCK FORMATION AND SITE CLASS IN BANDAR LAMPUNG

2020 ◽  
Vol 6 (3) ◽  
pp. 183-189
Author(s):  
Rustadi Rustadi ◽  
Eko Rananda
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Sedimentary Rock ◽  
Soil Characteristics ◽  
Shallow Depth ◽  
Site Class ◽  
Rock Formations ◽  
Class D ◽  
The Impact

Soil characteristics are important impact for the scale of damage caused by earthquake vibrations. The impact caused by an earthquake in a location depends on the shear wave velocity (Vs). The study examined the effect of sedimentary rock formations on shear wave velocity and site class based on SPT tests in two rock formations in Bandar Lampung. The value of Vs, Vs30 and site class is determined based on the N-SPT value. Older rock formations of Quaternary age, have produced compaction at a shallow depth of 2 m from the surface, with Vs30 360 m/s and site class C. While the formation is younger, compactions are formed at a depth of 20 m, Vs30 200 m/s and site class D.

scholarly journals Multi-method site characterization to verify the hard rock (Site Class A) assumption at 25 seismograph stations across Eastern Canada

2021 ◽  
pp. 875529302110010
Author(s):  
Sameer Ladak ◽  
Sheri Molnar ◽  
Samantha Palmer
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Hard Rock ◽  
Site Characterization ◽  
Eastern Canada ◽  
Site Class ◽  
Paleozoic Rock ◽  
Rock Types ◽  
Site Period

Site characterization is a crucial component in assessing seismic hazard, typically involving in situ shear-wave velocity ( VS) depth profiling, and measurement of site amplification including site period. Noninvasive methods are ideal for soil sites and become challenging in terms of field logistics and interpretation in more complex geologic settings including rock sites. Multiple noninvasive active- and passive-seismic techniques are applied at 25 seismograph stations across Eastern Canada. It is typically assumed that these stations are installed on hard rock. We investigate which site characterization methods are suitable at rock sites as well as confirm the hard rock assumption by providing VS profiles. Active-source compression-wave refraction and surface wave array techniques consistently provide velocity measurements at rock sites; passive-source array testing is less consistent but it is our most suitable method in constraining the rock VS. Bayesian inversion of Rayleigh wave dispersion curves provides quantitative uncertainty in the rock VS. We succeed in estimating rock VS at 16 stations, with constrained rock VS estimates at 7 stations that are consistent with previous estimates for Precambrian and Paleozoic rock types. The National Building Code of Canada uses solely the time-averaged shear-wave velocity of the upper 30 m ( VS30) to classify rock sites. We determine a mean VS30 of ∼ 1600 m/s for 16 Eastern Canada stations; the hard rock assumption is correct (>1500 m/s) but not as hard as often assumed (∼2000 m/s). Mean variability in VS30 is ∼400 m/s and can lead to softer rock classifications, in particular, for Paleozoic rock types with lower average rock VS near the hard/soft rock boundary. Microtremor and earthquake horizontal-to-vertical spectral ratios are obtained and provide site period classifications as an alternative to VS30.

scholarly journals A Comparative Study on the VS30 and N30 Based Seismic Site Classification in Kahramanmaras, Turkey

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Dalia Munaff Naji ◽  
Muge K. Akin ◽  
Ali Firat Cabalar
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Soil Structure ◽  
Site Response ◽  
Dead Sea ◽  
Site Classification ◽  
Earthquake Hazards ◽  
Class D ◽  
Average Shear

Assessment of seismic site classification (SSC) using either the average shear wave velocity (VS30) or the average SPT-N values (N30) for upper 30 m in soils is the simplest method to carry out various studies including site response and soil-structure interactions. Either the VS30- or the N30-based SSC maps designed according to the National Earthquake Hazards Reduction Program (NEHRP) classification system are effectively used to predict possible locations for future seismic events. The main goal of this study is to generate maps using the Geographic Information System (GIS) for the SSC in Kahramanmaras city, influenced by both East Anatolian Fault and Dead Sea Fault Zones, using both VS30 and N30 values. The study also presents a series of GIS maps produced using the shear wave velocity (VS) and SPT-N values at the depths of 5 m, 10 m, 15 m, 20 m, and 25 m. Furthermore, the study estimates the bed rock level and generates the SSC maps for the average VS values through overburden soils by using the NEHRP system. The VS30 maps categorize the study area mainly under class C and limited number of areas under classes B and D, whereas the N30 maps classify the study area mainly under class D. Both maps indicate that the soil classes in the study area are different to a high extent. Eventually, the GIS maps complied for the purpose of urban development may be utilized effectively by engineers in the field.

scholarly journals Risks of Solely Relying on VS30 in Ground Motion Response Studies

2018 ◽  
Vol 4 (12) ◽  
pp. 2937
Author(s):  
Amin Ghanbari ◽  
Younes Daghigh ◽  
Forough Hassanvand
Keyword(s):  
Shear Wave ◽  
Ground Motion ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Ground Surface ◽  
Earthquake Excitation ◽  
Site Class ◽  
Velocity Models ◽  
Average Shear ◽  
Classification Tool

The average shear wave velocity of the uppermost 30 m of earth (Vs30) is widely used in seismic geotechnical engineering and soil-structure interaction studies. In this regard, any given subsurface profile is assigned to a specific site class according to its average shear wave velocity. However, in a real-world scenario, entirely different velocity models could be considered in the same class type due to their identical average velocities. The objective of the present study is to underline some of the risks associated with solely using Vs30 as a classification tool. To do so, three imaginary soil profiles that are quite different in nature, but all with the same average Vs were considered and were subjected to the same earthquake excitation. Seismic records acquired at the ground surface demonstrated that the three sites have different ground motion amplifications. Then, the different ground responses were used to excite a five-story structure. Results confirmed that even sites from the same class can indeed exhibit different responses under identical seismic excitations. Our results demonstrated that caution should be practiced when large-contrast velocity models are involved as such profiles are prone to pronounced ground motion amplification. This study, which serves as link between soil dynamics and structural dynamics, warns practitioners about the risks associated with oversimplifying the subsurface profile. Such oversimplifications can potentially undermine the safety of existing or future structures.

scholarly journals Struktur Kecepatan Gelombang Geser (Vs) di Daerah Rawan Gerakan Tanah (Longsor) Jalan Lintas Kabupaten Bengkulu Tengah-Kepahiang

2021 ◽  
Vol 11 (2) ◽  
pp. 134
Author(s):  
Nanang Sugianto ◽  
Refrizon Refrizon
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Velocity Structure ◽  
Soft Rock ◽  
Rock Properties ◽  
Subsurface Structure ◽  
Class D ◽  
Class B ◽  
Hard Structures

Shear wave velocity <em>(V<sub>s</sub>)</em> structure at along of Central Bengkulu-Kepahiang crossline has been mapped. This research aims to identify the subsurface structure and to estimate the constituent material type of rock in landslide-prone areas (Central Bengkulu-Kepahiang crossline). Shear wave velocity structure on each site is obtained by the HVSR-inversion of 146 microtremor data (ambient noise recording of seismometer). <em>V<sub>s</sub></em> structure at the line mapped from the surface until to 30 meters of the depth. Groups of Vs are identified in class E (<em>V<sub>s</sub></em> &lt;180), Class D (180≤<em> V<sub>s</sub></em> &lt;360), Class C (360≤<em> V<sub>s</sub></em> &lt;760), and Class B (760≤<em> V<sub>s</sub></em> &lt;1500). The subsurface structure at the depth of 0 to 10 meters are dominated by stiff soil, very dense soil, and soft rock which has highly fractured and weathered rock properties. At the depth of 15 meters to 30 meters, the subsurface structure is dominated by hard rock but it is high potential or easy to fracturing and weathering like the properties of the rocks in areas that have landslides in the past. Based on <em>V<sub>s</sub></em> value, rock constituent materials are deposition of sand, clay, gravel and alluvium ranging from soft to relatively hard structures at the depth.

scholarly journals Shear Wave Velocity (Vs) at Reactor Building, Experimental Power Reactor Indonesia

2021 ◽  
Vol 2048 (1) ◽  
pp. 012040
Author(s):  
Eko Rudi Iswanto ◽  
Theo Alvin Ryanto ◽  
Abimanyu BW Setiaji ◽  
Hadi Suntoko
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Power Reactor ◽  
Soil Layer ◽  
Hydrogen Gas ◽  
Design Activity ◽  
Foundation Design ◽  
Site Class ◽  
Reactor Building

Abstract Experimental Power Reactor (RDE) is a Gen IV Reactor type with Hydrogen Gas Cooler. Despite this type of reactor has high safety performance, earthquake hazard should be demonstrated. Detail Engineering Design Activity on RDE has been conducted in the past 3 years. In the end of this phase, preliminary parameter design such as shear wave velocity (Vs) should be defined. This parameter correlated with subsurface condition which has high uncertainty. This study is conducted in order to estimate values of Vs. Generally, the data collection is carried out through geotechnical investigation but this method cost more time and resources. In the recent decades, another method has been widely introduced which is geophysical passive source Microtremor Array Measurement (MAM) with Spatial Auto Correlation (SPAC) method. This method can be used to estimate values of Vs and can be used as preliminary reference to define the position of borehole before construction phase getting started. The result shows, the location of reactor building is estimated to have 5 soil layers with varying Vs value. The Vs value of the first soil layer is about 152 m/s started from the surface to 8 m depth. The second soil layer has 169 m/s Vs value started from 8 m to 20 m depth. The third soil layer, started from 20 m to 36 m depth, has 384 m/s Vs value. The next layer as the fourth layer of soil, started from 36 m to 70 m depth with a value of Vs around 526 m/s. The last soil layer with a depth 70 m to 100 m, has Vs value of 667 m/s. Based on these Vs value estimation from surface to 30 m depth, the average value of the shear wave velocity (Vs 30) is m/s. Thus, reactor building is located in the site class SD with medium soil categories according to SNI 1726-2012. The foundation design and excavation planning phase, this information is needed.

scholarly journals Investigation of Soil Characterization in Hatay Province in Turkey by Using Seismic Refraction, Multichannel Analysis of Surface Waves and Microtremor

2021 ◽  
Vol 24 (4) ◽  
pp. 473-484
Author(s):  
Cengiz Kurtuluş ◽  
Ibrahim Sertcelik ◽  
Fadime Sertçelik ◽  
Hamdullah Livaoğlu ◽  
Cüneyt Şaş
Keyword(s):  
Surface Waves ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Seismic Refraction ◽  
Strong Motion ◽  
Site Classification ◽  
Eurocode 8 ◽  
Site Class ◽  
Multichannel Analysis

In this study, shallow seismic surveys, including seismic refraction, Multichannel Analysis of Surface Waves (MASW), Refraction Microtremor (ReMi), and Microtremor measurements were conducted to estimate site characterization at 26 strong-motion stations of AFAD (Disaster and Emergency Management Presidency) in the province of Hatay, situated in one of the most seismically active regions in southern Turkey. The Horizontal to vertical spectral ratio (HVSR) technique was applied, using smoothed Fourier spectra derived from a long duration series to determine dominant frequency values at different amplification levels. Shear wave velocity up to 30 m of the ground was detected with MASW analysis. In the ReMi analysis, up to 80 m was reached with a corresponding average of 650 m/s shear wave velocity. The shear wave velocities estimated by the MASW method up to 30 m were compared with those found by the ReMi method, and they were observed to be very compatible. The province of Hatay was classified according to Vs30 based NEHRP Provisions, Eurocode-8, the Turkish Building Earthquake Regulation (TBDY-2018), and Rodriguez-Marek et al. (2001). The shear-wave velocity (Vs30), Horizontal to Vertical ratio’s (H/V) peak amplitude, dominant period, and site class of each site were determined. The H/V peak amplitudes range between 1.9 and 7.6, while the predominant periods vary from 0.23 sec to 2.94sec in the study area. These results are investigated to explain the consistency of site classification schemes.

Sign in / Sign up

Export Citation Format

Share Document