Researches on the Structure of Rubber

1928 ◽  
Vol 1 (3) ◽  
pp. 401-409 ◽  
Author(s):  
Paul Bary ◽  
Ernst A. Hauser
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
X Ray ◽  
Physico Chemical

Abstract The theory according to which rubber consists of two components which normally are dissolved one in the other (Bary), is based on a number of physico-chemical observations, and is in general agreement with the results of x-ray work. The very nature of the x-ray diagrams substantiates the theory by introducing the idea that stretching rubber causes a separation of part of the dissolved component from its solvent (theory of Hauser and Mark). It may be concluded that rubber consists of a network of β-rubber which is capable of giving x-ray diagrams only when it is sufficiently condensed, that is, when its chains of carbon atoms have little freedom of oscillation. This result can be obtained either by freezing the rubber, which increases the proportion of the β-form, or by elongation, which expels the a-portion and concentrates the β-portion. This concept appears to explain all observations on the physical and mechanical properties of rubber.

Physical and Mechanical Properties of Tenun Pahang Fabrics using Alternative Yarns

2016 ◽  
Vol 13 (2) ◽  
pp. 67
Author(s):  
Engku Liyana Zafirah Engku Mohd Suhaimi ◽  
Jamil Salleh ◽  
Suzaini Abd Ghani ◽  
Mohamad Faizul Yahya ◽  
Mohd Rozi Ahmad
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Silk Fabrics ◽  
Recovery Angle ◽  
Made In

An investigation on the properties of Tenun Pahang fabric performances using alternative yarns was conducted. The studies were made in order to evaluate whether the Tenun Pahang fabric could be produced economically and at the same time maintain the fabric quality. Traditional Tenun Pahang fabric uses silk for both warp and weft. For this project, two alternative yarns were used which were bamboo and modal, which were a little lower in cost compared to silk. These yarns were woven with two variations, one with the yarns as weft only while maintaining the silk warp and the other with both warp and weft using the alternative yarns. Four (4) physical testings and three (3) mechanical testings conducted on the fabric samples. The fabric samples were evaluated including weight, thickness, thread density, crease recovery angle, stiffness and drapability. The results show that modal/silk and bamboo silk fabrics are comparable in terms of stiffness and drapability, hence they have the potential to replace 100% silk Tenun Pahang.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

scholarly journals Features of the hydration process of the modified blended cement for fiber cement panels

2018 ◽  
Vol 170 ◽  
pp. 03030 ◽  
Author(s):  
Rustem Mukhametrakhimov ◽  
Liliya Lukmanova
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Blended Cement ◽  
Physical And Mechanical Properties ◽  
Hydration Process ◽  
Cement Matrix ◽  
X Ray Diffraction ◽  
Structure Form ◽  
Silicate Phase ◽  
X Ray

The paper studies features of the hydration process of the modified blended cement for fiber cement panels (FCP) using differential thermal analysis, X-ray diffraction analysis, electron microscopy and infrared spectroscopy. It is found that deeper hydration process in silicate phase, denser and finer crystalline structure form in fiber cement matrix based on the modified blended cement. Generalization of this result to the case of fiber cement panels makes it possible to achieve formation of a denser and homogeneous structure with increased physical and mechanical properties.

scholarly journals EFFECT OF THERMO-MECHANICAL TREATMENT ON PROPERTIES OF PARICA PLYWOODS (Schizolobium amazonicum Huber ex Ducke)

2017 ◽  
Vol 41 (1) ◽  
Author(s):  
Mírian de Almeida Costa ◽  
Cláudio Henrique Soares Del Menezzi
Keyword(s):  
Mechanical Properties ◽  
Mechanical Treatment ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Modulus Of Rupture ◽  
Thermal Treatments ◽  
Mechanical Compression ◽  
Specific Mass ◽  
Thermo Mechanical Treatment ◽  
Temperature And Pressure

ABSTRACT Thermo-mechanical treatment is a technique for wood modification in which samples are densified by means of heat and mechanical compression, applied perpendicularly to fibers, which under different combinations of time, temperature, and pressure increases wood density and thus improve some of its properties. This study aimed to treat thermo-mechanically parica plywood and observe the effects on its physical and mechanical properties. Specimens were submitted to two treatments, 120 and 150 ºC, remaining under pressure for seven minutes and, subsequently, under zero pressure for 15 minutes. Results showed a significant increase in specific mass from 0.48 g cm-3 to an average of 0.56 g cm-3, and a compression ratio of about 31.7% on average. Physical properties also varied significantly and results showed that treated samples swelled and absorbed more water than those untreated, leading to a greater thickness non-return rate. This indicates the proposed thermal treatments did not release the internal compressive stress generated during panel pressing, not improving its dimensional stability as a result. On the other hand, mechanical properties were positively affected, leading to an increase of 27.5% and 51.8% in modulus of rupture after treatments at 120 and 150 ºC, respectively. Modulus of elasticity and glue-line shear strength did not vary statistically and Janka hardness was 29.7% higher after treatment at 150 ºC.

Contribution of the hybrid component to the structure and properties of ceramics based on metastable phases Al2O3

2021 ◽  
pp. 127-136
Author(s):  
A. V. Maletsky ◽  
T. E. Konstantinova ◽  
D. R. Belichko ◽  
G. K. Volkova ◽  
V. V. Burkhovetsky
Keyword(s):  
Mechanical Properties ◽  
Yttrium Aluminum Garnet ◽  
Metastable Phase ◽  
Physical And Mechanical Properties ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Mutual Inhibition ◽  
X Ray ◽  
Tetragonal Lattice ◽  
Yttrium Aluminum

The paper presents results of the study of the effect of doping with yttrium oxide on ceramics of the composition (γ + θ) Al2O3 + nY2O3 (n = 0, 1, 2, 3 wt%), sintered at 1550°C for 2 h, from powders of the specified composition annealed at temperatures of 500 , 800, 1000°С. X-ray diffraction analysis established the formation in ceramics of yttrium aluminum garnet Y3Al5O12 (YAG) and a metastable phase of the same composition with a tetragonal lattice type in powders at temperatures above 1200°C. The effect of YAG on the physical and mechanical properties was established: high properties were demonstrated by ceramics of the composition α-Al2O3 + 2wt% Y2O3, obtained from a powder annealed at 1000°C. In addition, high physical and mechanical properties were observed in ceramics of the composition α-Al2O3 + 0wt% Y2O3, obtained from a powder annealed at 800°C. The effect of the so-called “mutual protection against crystallization” was discovered, which consists in the mutual inhibition of crystallization processes in powders of the Al2O3 – Y2O3 system.

TiO2 and ZnO Water Sol Preparation by Sol–Gel Method and Application on Polyester Fabric of Antistatic Finishing

2011 ◽  
Vol 331 ◽  
pp. 270-274 ◽  
Author(s):  
Yan Yan Chu ◽  
Qing Wang ◽  
Shi Zhong Cui
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Sol Gel ◽  
Physical And Mechanical Properties ◽  
Polyester Fabric ◽  
Pure Tio2 ◽  
The Other ◽  
Baking Process ◽  
Result Show ◽  
The Stability

Abstract：Pure TiO2 water sol, pure ZnO water sol and three compound TiO2/ZnO water sols are prepared under low temperature. Then the padding and baking process is used to put the functional sol liquid on the fabric. SEM is use to analyzed the change of surface feature and the result show that all of the water sol except pure ZnO water sol liquid formed a thin film on the fiber The stability of pure ZnO water sol is the best one and the pure TiO2 water sol is the worst one at temperature of 15°C. The compound water sols stabilities are between these two water sols and with the more amount of ZnO, the stability last longer. Both mole of TiO2 and ZnO with the rate of 5 to 5 and 7 to 3 display the best antistatic behavior, but the washing fastnesses are not good. After treatment, the moisture regain displays most dramatically changes; the next one is whiteness of fabric, but the other physical and mechanical properties have a little change.

Physical and Mechanical Properties of Bi0.5(Na0.81K0.19)0.5TiO3 Ceramic Modified by KNbO3

2019 ◽  
Vol 805 ◽  
pp. 71-75
Author(s):  
Suchittra Inthong ◽  
Chatchai Kruae-In ◽  
Wuttikrai Thanomsiang ◽  
Suppanat Kosolwattana ◽  
Denis Russell Sweatman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mixed Oxides ◽  
Perovskite Phase ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Ceramic Samples ◽  
Pure Phase ◽  
Knoop Microhardness

This research reports the physical and mechanical properties of (1-x) Bi0.5(Na0.81K0.19)0.5TiO3-xKNbO3 (x=0.00-0.06) ceramics. The Modified Bi0.5(Na0.81K0.19)0.5TiO3 ceramics were synthesized by solid state reaction technique. The mixed oxides powders were calcined at 850 °C, 4 h and sintered at 1120 °C, 2 h to form pure phase perovskite and the optimum bulk density, respectively. The phase formation of the modified ceramic samples was determined by X-ray diffraction technique. All of the modified Bi0.5(Na0.81K0.19)0.5TiO3 ceramics exhibited a single perovskite phase. The bulk densities of the modified ceramic samples were 5.41±0.27-5.75±0.28 g/cm3 using the Archimedes’ method. The microstructure was revealed by the scanning electron microscope. The rectangular-like shape was found of all studied ceramics which had the grain size between 1.31±0.02-1.56±0.03 mm. The mechanical properties were studied by both Vickers and Knoop microhardness tester. The results are discussed in term of the relation among hardness properties, Young’s modulus, and fracture toughness.

Effect of Alumina (Al2O3) to the Properties of Whiteware Porcelain

2020 ◽  
Vol 1010 ◽  
pp. 194-199
Author(s):  
Hamdan Yahya ◽  
Aspaniza Ahmad ◽  
Ismail Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Water Absorption ◽  
Bulk Density ◽  
Physical And Mechanical Properties ◽  
Porcelain Body ◽  
The Other ◽  
Alumina Content ◽  
Crystalline Phases ◽  
Mullite Phase

The effect of Al2O3 to the properties of whiteware porcelain such as water absorption, bulk density, flexural strength and crystalline phases were studied systematically. The result shows that the addition of alumina at maximum 5 wt.% in porcelain bodies increased the flexural strength of the fired bodies which can reach 55.5 MPa, 30% higher than 0.0% alumina content. However, slight decrease in the other physical and mechanical properties was observed with Al2O3 addition higher than 5 wt.%, which is believed to be due to increased corundum phase compared to mullite phase in porcelain body.

Use of Ash from the Incineration of Elephant Grass (Pennisetum purpureums shaum) into Clayey Ceramic

2012 ◽  
Vol 727-728 ◽  
pp. 993-998 ◽  
Author(s):  
A.M.F.D. Silva ◽  
L.S. Lovise ◽  
Sérgio Neves Monteiro ◽  
Carlos Maurício Fontes Vieira
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Large Scale ◽  
Chemical Characterization ◽  
Physical And Mechanical Properties ◽  
Linear Shrinkage ◽  
The Other ◽  
Industrial Processes ◽  
Elephant Grass ◽  
Calcium Compounds

Ashes generated in industrial processes are usually discarded and contribute to environmental pollution. Large scale incorporation into clayey ceramic products for civil construction, such as bricks and tiles, could be a permanent solution. Based on this rationale, this works has as its objective to characterize an ash waste from the incineration of elephant grass and to evaluate its incorporation into a clay to produce red ceramic. The waste was submitted to mineralogical and chemical characterization. Compositions were prepared with incorporation of the waste in amounts of up to 20 wt.% into the clay. Specimens were prepared by extrusion and fired in a laboratory furnace at 850°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural strength. The results showed that the waste is mainly composed of quartz and calcium compounds that sensibly reduce the linear shrinkage and does not change the other properties of the ceramic.

SYNERGISTIC REINFORCEMENT OF ORGANOCLAY AND DOUBLE NETWORKING IN NATURAL RUBBER

2013 ◽  
Vol 86 (2) ◽  
pp. 205-217 ◽  
Author(s):  
Hedayatollah Sadeghi Ghari ◽  
Zahra Shakouri
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Natural Rubber ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Double Network ◽  
X Ray ◽  
Extension Ratio ◽  
Curing Characteristics ◽  
Scanning Electron

ABSTRACT Research was undertaken on natural rubber (NR) nanocomposites with organoclays. A double-network (DN) structure is formed when a partially cross-linked elastomer is further cross-linked during a state of strain. Two methods were used in the preparation of NR/organoclay nanocomposites: the ordinary method (single-network NR nanocomposite) and double-networked NR (DN-NR) nanocomposites. The single-networked NR nanocomposites were used for comparison. The effects of organoclay (5 phr) with a different extension ratio on curing characteristics, mechanical properties, hardness, swelling behavior, and morphology of single- and double-networked NR nanocomposites were studied. The results showed that double-networked NR nanocomposites exhibited higher physical and mechanical properties. The tensile strength of DN-NR nanocomposites increased up to 33 MPa (more than four times greater than that of pure NR) and then decreased with an increasing extension ratio. Modulus and hardness continuously increased with an increased extension ratio. The microstructure of the NR/organoclay systems was studied by X-ray diffraction and field emission scanning electron microscopy. The effects of different extension ratios on the dispersion of organoclay layers in the nanocomposites were investigated. Generally, results showed that the optimized extension ratio in DN nanocomposites was equal (or about or around) to α= 2.

Sign in / Sign up

Export Citation Format

Share Document