Comparing the Physico-Chemical Characteristics of Formulated and Marketed Yashada Bhasma

2021 ◽  
pp. 6392-6398
Author(s):  
Nitu Bhatnagar ◽  
Avani Pareek
Keyword(s):  
Inductively Coupled Plasma ◽  
Thermo Gravimetric Analysis ◽  
Human Consumption ◽  
Chemical Characteristics ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Physico Chemical ◽  
The Difference

The present study is aimed to observe the difference in the Physico-Chemical characteristics of the marketed and formulated bhasma samples through X-Ray Diffraction analysis (XRD), Dynamic Light Scattering (DLS), Zeta potential, Thermo-Gravimetric analysis (TGA), Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray analysis (EDAX), apart from organoleptic methods. Inductively Coupled Plasma Mass Spectroscopy (ICPMS) analysis was also done to observe the presence of trace and heavy metals so that the safety of all these samples could be ensured. XRD shows variation in oxide nature of zinc as well crystallite size in all bhasma samples. DLS and SEM results show difference in particle size of marketed bhasma samples as compared to formulated Yashada bhasma. EDAX and ICPMS also confirm the alteration in elemental composition of all these bhasma samples. Thus, it can be concluded that these ayurvedic medicines should be prepared strictly using the formulation methods as mentioned in the Ayurvedic texts. This will help the prepared products to adopt the inherent quality of the ancient system of medicine, which shall be useful and devoid of any side effects for human consumption.

Gemmological investigation of a synthetic blue beryl: a multi-methodological study

2008 ◽  
Vol 72 (3) ◽  
pp. 799-808 ◽  
Author(s):  
I. Adamo ◽  
G. D. Gatta ◽  
N. Rotiroti ◽  
V. Diella ◽  
A. Pavese
Keyword(s):  
Crystal Structure ◽  
Inductively Coupled Plasma ◽  
Tetrahedral Site ◽  
X Ray Diffraction ◽  
Thermo Gravimetric ◽  
X Ray ◽  
Cell Parameters ◽  
Inductively Coupled ◽  
The Difference ◽  
Difference Fourier

AbstractA multi-methodological investigation of a synthetic Cu/Fe-bearing blue beryl [IV(Be2.86Cu0.14)∑=3.00VI(Al1.83Fe3+0.14Mn2+0.03Mg0.03)∑=2.03IV(Si5.97Al0.03∑=6.00O18.(Li0.12Na0.04.0.40H2O)] has been performed by means of gemmological standard testing, electron microprobe chemical analyses, laser ablation inductively coupled plasma mass spectroscopy, thermo-gravimetric analyses, infrared spectroscopy and single-crystal X-ray diffraction in order to determine the gemmological properties, crystal structure and crystal-chemistry of this material. The increasing production of marketable hydrothermal synthetic beryls with 'exotic' colours and the small number of studies on the accurate location of chromophores in the crystal structure inspired this multi-methodological investigation. The X-ray structural refinements confirm that the space group of the Cu/Fe-bearing blue beryl is P6/mcc, with unit-cell parameters: 9.2483 ≤ a ≤ 9.2502 Å and 9.2184 ≤ c ≤ 9.2211 Å. The analysis of the difference Fourier maps of the electron density suggests that Cu is located at the tetrahedral site (Wyckoff 6fposition) along with Be, whereas Fe shares the octahedral site with Al (4c position). No evidence of extra-framework Cu/Fe-sites (i.e. channel sites) has been found. The Li is probably located at the extra-framework 2b site. Infrared spectra show that the H2O molecules are present with two configurations: one with the H···H vector oriented ‖[0001] and the other with H···H vector oriented ⊥[0001].

Synthesis and Characterization of Fe2+-CTS/CA-CNTs Composite and its Magnetic Properties

2013 ◽  
Vol 680 ◽  
pp. 49-53
Author(s):  
Chang Yu ◽  
Xu Zhang ◽  
Kan He ◽  
Yue Liu ◽  
Jie Shan Qiu
Keyword(s):  
Electron Microscopy ◽  
Magnetic Properties ◽  
Inductively Coupled Plasma ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Transmission Electron ◽  
Superparamagnetic State

A novel biocompatible Fe2+-chitosan (CTS)/citric acid modified carbon nanotube (CA-CNTs) composite (Fe2+-CTS/CA-CNTs) has been successfully synthesized by covalent bonding and crosslinking chemistry, followed by the reduction. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-Vis spectrum, X-ray diffraction (XRD), inductively coupled plasma (ICP), thermal gravimetric analysis (TGA), and vibrating sample magnetometer (VSM) techniques. The results show that the CTS has been successfully grafted to the CA-CNTs carrier and Fe2+ ions are absorbed on the CTS by coordination bond mode. It was found that the Fe2+-CTS/CA-CNTs composite shows good magnetic properties with a low ratio of remanence to saturation magnetization and is in a superparamagnetic state at room temperature. It is believed that the Fe2+-CTS/CA-CNTs composite will be potential for application in MRI.

scholarly journals Study of physico-chemical characteristics of nickel insertion in phosphogypsum

2016 ◽  
Vol 12 (6) ◽  
pp. 4134-4138
Author(s):  
H. Nafai ◽  
G. Lamzougui ◽  
A. Bouhaouss ◽  
R. Bchitou
Keyword(s):  
Inductively Coupled Plasma ◽  
Calcium Sulfate ◽  
Atomic Emission ◽  
X Ray Diffraction ◽  
Plasma Atomic Emission ◽  
Acid Attack ◽  
X Ray ◽  
Inductively Coupled ◽  
Physico Chemical ◽  
Maximum Content

The main purpose of this work is study the influence of the insertion metal ions Ni (II) in the phosphogypsum produced by sulfuric acid attack of tricalcium phosphate. Indeed, the maximum content of heavy metals calcium sulfate that can absorb was determined. The added ions are (NiCl2, 6H2O) with mass concentrations ranging from 5% to 50%. The samples prepared were characterized by various methods, such as X-ray diffraction (XRD), infrared spectroscopy and inductively coupled plasma atomic emission spectroscopy (ICP-AES). The results of this study showed that the limit of insertion of metal cations in calcium sulfate is limited to 30% for nickel.

scholarly journals Rapid four-component synthesis of dihydropyrano[2,3-c]pyrazoles using nano-eggshell/Ti(IV) as a highly compatible natural based catalyst

BMC Chemistry ◽  
2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Arefeh Dehghani Tafti ◽  
Bi Bi Fatemeh Mirjalili ◽  
Abdolhamid Bamoniri ◽  
Naeimeh Salehi
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Reaction Times ◽  
Diffraction Field ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solvent Free Conditions ◽  
High Yields ◽  
Work Up

AbstractNano-eggshell/Ti(IV) as a novel naturally based catalyst was prepared, characterized and applied for the synthesis of dihydropyrano[2,3-c]pyrazole derivatives. The characterization of nano-eggshell/Ti(IV) was performed using Fourier Transform Infrared spectroscopy, X-ray Diffraction, Field Emission Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy, and Thermo Gravimetric Analysis. Dihydropyrano[2,3-c]pyrazoles were synthesized in the presence of nano-eggshell/Ti(IV) via a four component reaction of aldehydes, ethyl acetoacetate, malononitrile and hydrazine hydrate at room temperature under solvent free conditions. The principal affairs of this procedure are mild condition, short reaction times, easy work-up, high yields, reusability of the catalyst and the absence of toxic organic solvents.

scholarly journals Enhanced Photocatalytic Activity of Cu2O Cabbage/RGO Nanocomposites under Visible Light Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1712
Author(s):  
Appusamy Muthukrishnaraj ◽  
Salma Ahmed Al-Zahrani ◽  
Ahmed Al Otaibi ◽  
Semmedu Selvaraj Kalaivani ◽  
Ayyar Manikandan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermo Gravimetric Analysis ◽  
Visible Region ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Pollutants ◽  
Transmission Electron

Towards the utilization of Cu2O nanomaterial for the degradation of industrial dye pollutants such as methylene blue and methyl orange, the graphene-incorporated Cu2O nanocomposites (GCC) were developed via a precipitation method. Using Hummers method, the grapheme oxide (GO) was initially synthesized. The varying weight percentages (1–4 wt %) of GO was incorporated along with the precipitation of Cu2O catalyst. Various characterization techniques such as Fourier-transform infra-red (FT-IR), X-ray diffraction (XRD), UV–visible diffused reflectance (UV-DRS), Raman spectroscopy, thermo gravimetric analysis (TGA), energy-dispersive X-ray analysis (EDX), and electro chemical impedance (EIS) were followed for characterization. The cabbage-like morphology of the developed Cu2O and its composites were ascertained from field-emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HR-TEM). In addition, the growth mechanism was also proposed. The results infer that 2 wt % GO-incorporated Cu2O composites shows the highest value of degradation efficiency (97.9% and 96.1%) for MB and MO at 160 and 220 min, respectively. Further, its catalytic performance over visible region (red shift) was also enhanced to an appreciable extent, when compared with that of other samples.

The Characteristic Evaluation of Hydroxyapatite Powders Synthesized from CaCO3 Refined from Oyster Shell and H3PO4

2006 ◽  
Vol 118 ◽  
pp. 639-644
Author(s):  
Hye Sung Kim ◽  
Su Chak Ryu
Keyword(s):  
Bone Density ◽  
Inductively Coupled Plasma ◽  
Oyster Shell ◽  
Atomic Emission ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Infra Red ◽  
Ft Ir

Hydroxyapatite (Ca10(PO4)6(OH)2, HAp) powders is synthesized using the mixed powders of CaCO3 refined from oyster shells and phosphoric acid (H3PO4-98%, Daejung) as starting materials. The characteristic evaluation and chemical analysis of the synthesized powders is performed by X-ray diffraction (XRD), Fourier-transformed infra-red spectroscopy (FT-IR), and inductively-coupled plasma atomic emission spectroscopy (ICPAES). XRD analysis of synthetic powder by heat treatment at 1300°C for 2hrs shows only HAp peaks corresponding to stoichiometric HAp. It is confirmed by ICP-AES test that impurities such as Zn, In, Ti, Ba, Cd, Pb, and Mn, is not detected at all, but small amounts of Ti and Be is observed (0.099ppm Ti and 0.002ppm Ba). Variation of bone density is measured by giving medication of HAp powder with drinking water into human body continuously for three month. After the medication, the bone density is higher than the medication before. This means that HAp powder made from this process can be used as improver of bone density.

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

scholarly journals Characterization of Fly Ash Generated from Matla Power Station in Mpumalanga, South Africa

2012 ◽  
Vol 9 (4) ◽  
pp. 1788-1795 ◽  
Author(s):  
Olushola S. Ayanda ◽  
Olalekan S. Fatoki ◽  
Folahan A. Adekola ◽  
Bhekumusa J. Ximba
Keyword(s):  
Fly Ash ◽  
Inductively Coupled Plasma ◽  
Coal Fly Ash ◽  
Harmful Effect ◽  
Point Of Zero Charge ◽  
X Ray Diffraction ◽  
Power Station ◽  
X Ray ◽  
Inductively Coupled ◽  
Plasma Mass Spectrometry

In this study, fly ash was obtained from Matla power station and the physicochemical properties investigated. The fly ash was characterized by x-ray fluorescence, x-ray diffraction, scanning electron microscopy, and inductively coupled plasma mass spectrometry. Surface area, particle size, ash and carbon contents, pH, and point of zero charge were also measured. The results showed that the fly ash is alkaline and consists mainly of mullite (Al6Si2O13) and quartz (SiO2). Highly toxic metals As, Sb, Cd, Cr, and Pb as well as metals that are essential to health in trace amounts were also present. The storage and disposal of coal fly ash can thus lead to the release of leached metals into soils, surface and ground waters, find way into the ecological systems and then cause harmful effect to man and its environments.

scholarly journals A study concerning the pretreatment of CNTs and its influence on the performance of NIB/CNTs amorphous catalyst

2006 ◽  
Vol 71 (11) ◽  
pp. 1153-1160 ◽  
Author(s):  
Chang Hu-Yuan ◽  
Feng Li ◽  
Li. Hua ◽  
Bin Zhang
Keyword(s):  
Selective Hydrogenation ◽  
Inductively Coupled Plasma ◽  
Acid Treatment ◽  
Chemical Reduction ◽  
X Ray Diffraction ◽  
Chemical Reduction Method ◽  
X Ray ◽  
Inductively Coupled ◽  
Selective Hydrogenation Of Acetylene ◽  
Transmission Electron

As prepared carbon nanotubes were pretreated with nitric acid (CNTs-HNO3) or ammonia (CNTs-NH3). Fourier transform infrared spectroscopy (FTIR) measurements showed that the surface of the nanotubes was functionalized with carboxylic and hydroxyl functional groups after the acid treatment and that basic groups containing nitrogen, such as N-H and C-N, were introduced to the surface of the nanotubes after the ammonia treatment. X-Ray diffraction analysis implied that the nickel residue in the CNTs was effectively removed by acid treatment. However, the nickel residue was only partially eliminated by ammonia pretreatment. NiB amorphous catalysts supported on CNTs-HNO3 and CNTs-NH3 were prepared by the impregnation-chemical reduction method and characterized by transmission electron microscopy (TEM), as well as inductively coupled plasma (ICP) spectroscopy and studied in the selective hydrogenation of acetylene. TEM measurements showed that a high density NiB particles of about 9 nm were homogeneously dispersed on the CNTs-NH3. However, NiB particles (13-23 nm)with amean size of 16 nm were scattered on the CNTs-HNO3.As a result, the activity and selectivity of NiB/CNTs-NH3 were higher than those of NiB/CNTs-HNO3 in the selective hydrogenation of acetylene.

Investigations on Cu2+-substituted Ni–Zn ferrite nanoparticles

2016 ◽  
Vol 30 (32n33) ◽  
pp. 1650347
Author(s):  
Amarjeet ◽  
Vinod Kumar
Keyword(s):  
Spinel Phase ◽  
Thermo Gravimetric Analysis ◽  
Peak Position ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Zn Ferrite

[Formula: see text] ([Formula: see text] = 0.1, 0.3 and 0.5) nanoparticles were prepared by chemical co-precipitation method. The developed nanoparticles were characterized for structural properties by powder X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. Peak position in the X-ray diffraction pattern confirmed the single spinel phase of the developed particles. Infrared (IR) spectroscopy in mid-IR range showed the presence of characteristic absorption bands corresponding to octahedral and tetrahedral bonds in the spinel structure of prepared samples. Thermo-gravimetric analysis (TGA) measurements showed a considerable weight loss in the developed samples above 700[Formula: see text]C. Frequency dependence of the electrical properties of the developed material pellets was studied in the frequency range of 1 kHz–5 MHz. Temperature dependence of the dielectric constant of [Formula: see text] was studied at different temperatures, i.e. at 425, 450 and 475 K, in the frequency range of 1 kHz–5 MHz. It was found that the electrical conductivity decreases with increasing Cu[Formula: see text] ion content while it increases with the increase in temperature.

Sign in / Sign up

Export Citation Format

Share Document