Poverty in the Dolnośląskie Voivodship

2016 ◽  
Vol 61 (6) ◽  
pp. 70-85
Author(s):  
Agata Girul

The article presents selected aspects of economic poverty in the Dolnośląskie Voivodship on the background of the country and other voivodships, as well as in the cross-section of the Dolnośląskie powiats in 2013, as compared to 2010. The comparative analysis of poverty level by powiats was presented by means of taxonomic synthetic measure based on a set of three selected diagnostic indicators. A complement to the objective assessment of poverty in the Dolnośląskie Voivodship was a presentation of results of subjective assessment of material situation of households in the voivodships’ cross-section.

Author(s):  
A. Yu. Kapustsinski ◽  
S. N. Kаnstantsinava

The paper deals with the problem of increasing the efficiency of the functioning of electric networks up to 1 kV, namely, the possibility of increasing the sensitivity of protections in networks up to 1 kV, which helps to reduce the protection response currents and, accordingly, reduce the cross-section of cable and wire products. The topicality of this problem is shown and the research tasks are defined. Much attention is paid to the concept of selectivity; attention is also paid to the concepts of full and partial selectivity. “Which protective devices can be considered selective?” is a question that is considered and worked out in sufficient depth in the paper. The negative phenomena that occur when ensuring the selectivity of protections in networks up to 1 kV are systematized and described in detail. Based on a comparative analysis of the parameters of circuit breakers with release tripping devices of various types, a solution to this problem is proposed by using circuit breakers with microprocessor and semiconductor release tripping devices. Additional advantages of microprocessor-based circuit breakers are considered and indicated, as well as their disadvantages are indicated, too. The main expected positive effects from the use of circuit breakers with microprocessor release tripping devices are listed, taking into account the fact that this type of circuit breakers is considered as a complex of devices replaced by it. The article can be recommended to employees of electric power specialties working with networks up to 1 kV.


Author(s):  
Andrii Bidakov ◽  
Evhenyi Raspopov ◽  
Oksana Pustovoitova

Design of joints of LVL elements with glued-in steel rods and metal connectors is considered as semi-rigid connection and requires taking of account the compliance. A comparative analysis of the test results of the beams with a metal connector and glued-in steel rods as well as solid beams is made in the paper. Design method of glued-in rods in LVL is proposed and taken into account failure mode. It allows reducing the distance between the axes of the rods as well as the distance from the rod axіs to the edges in the cross section of the beam and increasing the joint strength.


Hand Surgery ◽  
2011 ◽  
Vol 16 (01) ◽  
pp. 49-54 ◽  
Author(s):  
T. J. Colegate-Stone ◽  
S. Garg ◽  
A. Subramanian ◽  
G. V. Mani

We performed a prospective cohort comparative analysis of simple trapezectomy and trapezectomy with pyrocarbon interposition in 38 consecutive patients with trapeziometacarpal joint osteoarthrosis. Patients were assessed preoperatively, at six and 12 months postoperatively using subjective and objective tools. Subjective assessment was performed using the Quick Disabilities of the Arm, Shoulder, and Hand questionnaire and the visual analogue score. Objective assessment was performed with grip strength measurements. At each time interval, statistical differences were sought between the two subgroups. No significant difference between the two subgroups was noted at any time interval on subjective or objective assessment. A significant difference (p < 0.05) was found on comparing the respective preoperative and 12-month subjective scores in both subgroups. Of the pyrocarbon subgroup seven had related complications. We suggest that pyrocarbon interposition does not significantly improve postoperative function, requires a longer operation with a high postoperative risk of pyrocarbon displacement and need for revision surgery.


Author(s):  
V. Mizuhira ◽  
Y. Futaesaku

Previously we reported that tannic acid is a very effective fixative for proteins including polypeptides. Especially, in the cross section of microtubules, thirteen submits in A-tubule and eleven in B-tubule could be observed very clearly. An elastic fiber could be demonstrated very clearly, as an electron opaque, homogeneous fiber. However, tannic acid did not penetrate into the deep portion of the tissue-block. So we tried Catechin. This shows almost the same chemical natures as that of proteins, as tannic acid. Moreover, we thought that catechin should have two active-reaction sites, one is phenol,and the other is catechole. Catechole site should react with osmium, to make Os- black. Phenol-site should react with peroxidase existing perhydroxide.


Author(s):  
Tamotsu Ohno

The energy distribution in an electron; beam from an electron gun provided with a biased Wehnelt cylinder was measured by a retarding potential analyser. All the measurements were carried out with a beam of small angular divergence (<3xl0-4 rad) to eliminate the apparent increase of energy width as pointed out by Ichinokawa.The cross section of the beam from a gun with a tungsten hairpin cathode varies as shown in Fig.1a with the bias voltage Vg. The central part of the beam was analysed. An example of the integral curve as well as the energy spectrum is shown in Fig.2. The integral width of the spectrum ΔEi varies with Vg as shown in Fig.1b The width ΔEi is smaller than the Maxwellian width near the cut-off. As |Vg| is decreased, ΔEi increases beyond the Maxwellian width, reaches a maximum and then decreases. Note that the cross section of the beam enlarges with decreasing |Vg|.


2009 ◽  
Author(s):  
Marci Culley ◽  
Holly Angelique ◽  
Courte Voorhees ◽  
Brian John Bishop ◽  
Peta Louise Dzidic ◽  
...  

The work of multilayer glass structures for central and eccentric compression and bending are considered. The substantiation of the chosen research topic is made. The description and features of laminated glass for the structures investigated, their characteristics are presented. The analysis of the results obtained when testing for compression, compression with bending, simple bending of models of columns, beams, samples of laminated glass was made. Overview of the types and nature of destruction of the models are presented, diagrams of material operation are constructed, average values of the resistance of the cross-sections of samples are obtained, the table of destructive loads is generated. The need for development of a set of rules and guidelines for the design of glass structures, including laminated glass, for bearing elements, as well as standards for testing, rules for assessing the strength, stiffness, crack resistance and methods for determining the strength of control samples is emphasized. It is established that the strength properties of glass depend on the type of applied load and vary widely, and significantly lower than the corresponding normative values of the strength of heat-strengthened glass. The effect of the connecting polymeric material and manufacturing technology of laminated glass on the strength of the structure is also shown. The experimental values of the elastic modulus are different in different directions of the cross section and in the direction perpendicular to the glass layers are two times less than along the glass layers.


Sign in / Sign up

Export Citation Format

Share Document