scholarly journals Optimization of Lift-Curve Slope for Wing-Fuselage Combination

Aerodynamics ◽  
2021 ◽  
Author(s):  
Vladimir Frolov
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Circular Cross Section ◽  
Cross Flow ◽  
Theoretical Data ◽  
Vortex Method ◽  
Relative Width ◽  
Elliptical Cross ◽  
Proposed Model ◽  
Lift Curve

The paper presents results obtained by the author for wing-body interference. The lift-curve slopes of the wing-body combinations are considered. A 2D potential model for cross-flow around the fuselage and a discrete vortex method (DVM) are used. Flat wings of various forms and the circular and elliptical cross sections of the fuselage are considered. It was found that the value of the lift-curve slopes of the wing-body combinations may exceed the same value for an isolated wing. An experimental and theoretical data obtained by other authors earlier confirm this result. Investigations to optimize the wing-body combination were carried within the framework of the proposed model. It was revealed that the maximums of the lift-curve slopes for the optimal midwing configuration with elliptical cross-section body had a sufficiently large relative width (more than 30% of the span wing). The advantage of the wing-fuselage combination with a circular cross section over an isolated wing for wing aspect ratio greater than 6 can reach 7.5% at the relative diameter of fuselage equal to approximately 0.2.

Numerical Study of Incomplete Stent Apposition Caused by Deploying Undersized Stent in Arteries With Elliptical Cross Sections

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Bo Jiang ◽  
Vikas Thondapu ◽  
Eric K. W. Poon ◽  
Peter Barlis ◽  
Andrew S. H. Ooi
Keyword(s):  
Shear Rate ◽  
Cross Section ◽  
Cross Sections ◽  
Numerical Study ◽  
Circular Cross Section ◽  
Blood Stream ◽  
Cfd Simulations ◽  
Elliptical Cross ◽  
Incomplete Stent Apposition ◽  
Computational Fluid Dynamics Cfd

Incomplete stent apposition (ISA) is one of the causes leading to poststent complications, which can be found when an undersized or an underexpanded stent is deployed at lesions. The previous research efforts have focused on ISA in idealized coronary arterial geometry with circular cross section. However, arterial cross section eccentricity plays an important role in both location and severity of ISA. Computational fluid dynamics (CFD) simulations are carried out to systematically study the effects of ISA in arteries with elliptical cross section, as such stents are partially embedded on the minor axis sides of the ellipse and malapposed elsewhere. Overall, ISA leads to high time-averaged wall shear stress (TAWSS) at the proximal end of the stent and low TAWSS at the ISA transition region and the distal end. Shear rate depends on both malapposition distance and blood stream locations, which is found to be significantly higher at the inner stent surface than the outer surface. The proximal high shear rate signifies increasing possibility in platelet activation, when coupled with low TAWSS at the transition and distal regions which may indicate a nidus for in-stent thrombosis.

scholarly journals Computational Study of Zigzag Spacer Design with Elliptical Cross-Section Filaments

2020 ◽  
Vol 307 ◽  
pp. 01047
Author(s):  
Gohar Shoukat ◽  
Farhan Ellahi ◽  
Muhammad Sajid ◽  
Emad Uddin
Keyword(s):  
Mass Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Computational Study ◽  
Flow Direction ◽  
Three Dimensional ◽  
Circular Cross Section ◽  
Two Dimensional ◽  
Permeate Flux ◽  
Elliptical Cross

The large energy consumption of membrane desalination process has encouraged researchers to explore different spacer designs using Computational Fluid Dynamics (CFD) for maximizing permeate per unit of energy consumed. In previous studies of zigzag spacer designs, the filaments are modeled as circular cross sections in a two-dimensional geometry under the assumption that the flow is oriented normal to the filaments. In this work, we consider the 45° orientation of the flow towards the three-dimensional zigzag spacer unit, which projects the circular cross section of the filament as elliptical in a simplified two-dimensional domain. OpenFOAM was used to simulate the mass transfer enhancement in a reverse-osmosis desalination unit employing spiral wound membranes lined with zigzag spacer filaments. Properties that impact the concentration polarization and hence permeate flux were analyzed in the domain with elliptical filaments as well as a domain with circular filaments to draw suitable comparisons. The range of variation in characteristic parameters across the domain between the two different configurations is determined. It was concluded that ignoring the elliptical projection of circular filaments to the flow direction, can introduce significant margin of error in the estimation of mass transfer coefficient.

On the Choice of Initial Geometric Imperfections in Externally Pressurized Shells

1999 ◽  
Vol 121 (1) ◽  
pp. 71-76 ◽  
Author(s):  
J. Błachut ◽  
O. R. Jaiswal
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Carrying Capacity ◽  
Circular Cross Section ◽  
Load Carrying Capacity ◽  
Geometric Imperfections ◽  
Elliptical Cross ◽  
Buckling Strength ◽  
Load Carrying ◽  
Initial Geometric Imperfections

Localized and global, of eigenmode type, initial geometric imperfections were superimposed on perfect torispherical, ellipsoidal, and toroidal shells of circular and elliptical cross section. Reduction of the load-carrying capacity was then calculated numerically for various geometries and the yield point of material which was assumed to be mild steel. Results show that the buckling strength of torispheres and ellipsoids could be strongly affected by imperfections, but reduction of its magnitude was dependent on the choice of imperfection shape and, more importantly, on the imperfection’s location. Calculations carried out for closed toroids of circular cross section show that these shells are not sensitive to eigenmode-type imperfections, while toroids with elliptical cross sections are sensitive to eigen-imperfections.

Analytical and Experimental Characterization of Flow in Slowly-Varying Cross-Section Microchannels

2010 ◽  
Author(s):  
M. Akbari ◽  
M. Bahrami ◽  
D. Sinton
Keyword(s):  
Pressure Drop ◽  
Cross Section ◽  
Cross Sections ◽  
Rectangular Cross Section ◽  
Arbitrary Cross Section ◽  
Geometrical Parameters ◽  
Elliptical Cross ◽  
Proposed Model ◽  
Hyperbolic Contraction ◽  
Asymmetric Microchannel

This paper outlines a novel approximate solution for determining the pressure drop of laminar, single-phase flow in slowly-varying microchannels of arbitrary cross-section. The proposed analysis is general and applicable to symmetric and asymmetric microchannel cross-sections, as examples compact relationships are reported for elliptical and rectangular shapes for three common wall profiles of linear, sinusoidal and hyperbolic. An experimental setup is designed and pressure drop measurements are conducted to validate the proposed model for streamwised periodic microchannels with rectangular cross-section and linear wall with a range of channel geometrical parameters such as aspect ratio and channel slope. The model is also compared against the numerical and experimental data of hyperbolic contraction with rectangular cross-section collected by others. It is observed that although the proposed model is based on the solution of the elliptical cross-section, it can accurately predict the pressure drop in microchannels of rectangular cross-section.

scholarly journals Effect of shaping on turbulent dynamics in reversed-field pinch simulations

2021 ◽  
Vol 87 (6) ◽  
Author(s):  
Robert Chahine ◽  
Kai Schneider ◽  
Wouter J.T. Bos
Keyword(s):  
Magnetic Field ◽  
Cross Section ◽  
Cross Sections ◽  
Circular Cross Section ◽  
Hydrodynamic Pressure ◽  
Magnetic Pressure ◽  
Reversed Field Pinch ◽  
Plasma Dynamics ◽  
Elliptical Cross ◽  
Reversed Field

We study the influence of the shape of the plasma container on the dynamics of the reversed-field pinch (RFP). The geometries we consider are periodic cylinders with elliptical and circular-shaped cross-sections. Numerical simulations of fully nonlinear viscoresistive magnetohydrodynamics are carried out to illustrate how the plasma dynamics is affected by shaping. It is shown that independent of the plasma shape, the quantity $\beta$ , comparing the hydrodynamic pressure to the magnetic pressure, decreases for increasing values of the Lundquist number, but the pressure gradient fluctuations remain roughly constant, when compared to the Lorentz force. Different elliptical shapes of the cross-section of the domain lead to the excitation of different toroidal (or axial) magnetic and dynamic modes. Furthermore, it is found that in a geometry with circular cross-section, a significant local poloidal angular momentum is observed, absent in the geometries with elliptical cross-section. Because the confinement is dominantly determined by plasma movement, and the dynamics of the velocity and magnetic field are modified by the modification of the geometry, shaping can thus affect the performance of RFP devices.

scholarly journals Asymptotic Behavior of Stable Structures Made of Beams

2021 ◽  
Author(s):  
Georges Griso ◽  
Larysa Khilkova ◽  
Julia Orlik ◽  
Olena Sivak
Keyword(s):  
Asymptotic Behavior ◽  
Cross Section ◽  
Cross Sections ◽  
Linear Elasticity ◽  
Circular Cross Section ◽  
Linear Elasticity Theory ◽  
Linear Elastic ◽  
The Cross ◽  
Small Rotation ◽  
Stable Structures

AbstractIn this paper, we study the asymptotic behavior of an $\varepsilon $ ε -periodic 3D stable structure made of beams of circular cross-section of radius $r$ r when the periodicity parameter $\varepsilon $ ε and the ratio ${r/\varepsilon }$ r / ε simultaneously tend to 0. The analysis is performed within the frame of linear elasticity theory and it is based on the known decomposition of the beam displacements into a beam centerline displacement, a small rotation of the cross-sections and a warping (the deformation of the cross-sections). This decomposition allows to obtain Korn type inequalities. We introduce two unfolding operators, one for the homogenization of the set of beam centerlines and another for the dimension reduction of the beams. The limit homogenized problem is still a linear elastic, second order PDE.

scholarly journals Effect of liquid cooling on PCR performance with the parametric study of cross-section shapes of microchannels

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yousef Alihosseini ◽  
Mohammad Reza Azaddel ◽  
Sahel Moslemi ◽  
Mehdi Mohammadi ◽  
Ali Pormohammad ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Heat Sink ◽  
Evaluation Criteria ◽  
Circular Cross Section ◽  
Microchannel Heat Sink ◽  
Liquid Cooling ◽  
Maximum Heat ◽  
Maximum Heat Transfer

AbstractIn recent years, PCR-based methods as a rapid and high accurate technique in the industry and medical fields have been expanded rapidly. Where we are faced with the COVID-19 pandemic, the necessity of a rapid diagnosis has felt more than ever. In the current interdisciplinary study, we have proposed, developed, and characterized a state-of-the-art liquid cooling design to accelerate the PCR procedure. A numerical simulation approach is utilized to evaluate 15 different cross-sections of the microchannel heat sink and select the best shape to achieve this goal. Also, crucial heat sink parameters are characterized, e.g., heat transfer coefficient, pressure drop, performance evaluation criteria, and fluid flow. The achieved result showed that the circular cross-section is the most efficient shape for the microchannel heat sink, which has a maximum heat transfer enhancement of 25% compared to the square shape at the Reynolds number of 1150. In the next phase of the study, the circular cross-section microchannel is located below the PCR device to evaluate the cooling rate of the PCR. Also, the results demonstrate that it takes 16.5 s to cool saliva samples in the PCR well, which saves up to 157.5 s for the whole amplification procedure compared to the conventional air fans. Another advantage of using the microchannel heat sink is that it takes up a little space compared to other common cooling methods.

Numerical Investigation of Cross-Section on Aluminum A6063 Thin-Walled Structures under Low-Velocity Impact Loading

2014 ◽  
Vol 1019 ◽  
pp. 96-102
Author(s):  
Ali Taherkhani ◽  
Ali Alavi Nia
Keyword(s):  
Energy Absorption ◽  
Cross Section ◽  
Cross Sections ◽  
Peak Load ◽  
Circular Cross Section ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Crush Strength

In this study, the energy absorption capacity and crush strength of cylindrical thin-walled structures is investigated using nonlinear Finite Elements code LS-DYNA. For the thin-walled structure, Aluminum A6063 is used and its behaviour is modeled using power-law equation. In order to better investigate the performance of tubes, the simulation was also carried out on structures with other types of cross-sections such as triangle, square, rectangle, and hexagonal, and their results, namely, energy absorption, crush strength, peak load, and the displacement at the end of tubes was compared to each other. It was seen that the circular cross-section has the highest energy absorption capacity and crush strength, while they are the lowest for the triangular cross-section. It was concluded that increasing the number of sides increases the energy absorption capacity and the crush strength. On the other hand, by comparing the results between the square and rectangular cross-sections, it can be found out that eliminating the symmetry of the cross-section decreases the energy absorption capacity and the crush strength. The crush behaviour of the structure was also studied by changing the mass and the velocity of the striker, simultaneously while its total kinetic energy is kept constant. It was seen that the energy absorption of the structure is more sensitive to the striker velocity than its mass.

Stresses and Deformations of Toroidal Shells of Elliptical Cross Section: With Applications to the Problems of Bending of Curved Tubes and of the Bourdon Gage

1952 ◽  
Vol 19 (1) ◽  
pp. 37-48
Author(s):  
R. A. Clark ◽  
T. I. Gilroy ◽  
E. Reissner
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Practical Interest ◽  
Closed Shell ◽  
Open Shell ◽  
Elliptical Cross Section ◽  
Axially Symmetric ◽  
Elliptical Cross ◽  
Two Parameters ◽  
Toroidal Shells

Abstract This paper is concerned with the application of the theory of thin shells to several problems for toroidal shells with elliptical cross section. These problems are as follows: (a) Closed shell subjected to uniform normal wall pressure. (b) Open shell subjected to end bending moments. (c) Combination of the results for the first and second problems in such a way as to obtain results for the stresses and deformations in Bourdon tubes. In all three problems the distribution of stresses is axially symmetric but only in the first problem are the displacements axially symmetric. The magnitude of stresses and deformations for given loads depends in all three problems on the magnitude of the two parameters bc/ah and b/c where b and c are the semiaxes of the elliptical section, a is the distance of the center of the section from the axis of revolution, and h is the thickness of the wall of the shell. For sufficiently small values of bc/ah trigonometric series solutions are obtained. For sufficiently large values of bc/ah asymptotic solutions are obtained. Numerical results are given for various quantities of practical interest as a function of bc/ah for the values 2, 1, 1/2, 1/4 of the semiaxes ratio b/c. It is suggested that the analysis be extended to still smaller values of b/c and to cross sections other than elliptical.

scholarly journals Particle separation of a modified feed nozzle hydrocyclone under different operating parameters

2021 ◽  
Vol 11 (5) ◽  
pp. 159-170
Author(s):  
Zsolt Hegyes ◽  
Máté Petrik ◽  
L. Gábor Szepesi
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Rectangular Cross Section ◽  
Circular Cross Section ◽  
Particle Separation ◽  
Baffle Plate ◽  
Important Data ◽  
Preliminary Research ◽  
All Speeds ◽  
Plate Solution

During the operation of the hydrocyclone the cut size diameter is the most important data. This is connected to feed rate, which is closely related to the feed cross section. Preliminary research has revealed that square cross-section is more effective than circular cross-section. The research compared 2 types of feed cross sections at 5 different feed rates. One is a standard rectangular cross-section and the other is a square cross-section that narrows with a baffle plate. Preliminary calculations for cut size diameter have shown that better particle separation at all speeds can be achieved with the baffle plate solution. In both types, the increased velocity created decreased cut size diameter. During the simulation, the baffle plate did not cause any abnormalities in the internal pressure and velocity distributions. The simulation revealed that the particles did not behave as previously calculated.

Sign in / Sign up

Export Citation Format

Share Document