An Engineer’s Introduction to PERT Scheduling and Control

1966 ◽  
Vol 3 (02) ◽  
pp. 225-229
Author(s):  
Vernon C. Honsinger
Keyword(s):  
Program Evaluation ◽  
Engineering Project ◽  
Expected Time ◽  
Time Estimates ◽  
Complex Engineering ◽  
And Control

Program Evaluation and Review Technique (PERT) is a method of planning work, comparing status with schedule, and evaluating progress at all levels of management in order to better control a major, complex, engineering project. PERT/COST adds control of manpower and funds. Three time estimates—optimistic, most likely, and pessimistic—are combined to obtain an expected time for completing each activity. The PERT network shows interdependencies of activities. An important result of the PERT calculations is the determination of the critical and slack paths of the network.

Ultrastructural changes in sciatic nerve tissue: Effects of passive maternal smoking

1983 ◽  
Vol 41 ◽  
pp. 650-651
Author(s):  
Amankwah K.S. ◽  
A.D. Weberg ◽  
R.C. Kaufmann
Keyword(s):  
Sciatic Nerve ◽  
Maternal Smoking ◽  
Ultrastructural Level ◽  
Uranyl Acetate ◽  
Nerve Tissue ◽  
Ultrastructural Changes ◽  
Cacodylate Buffer ◽  
And Control ◽  
Spontaneous Delivery

Previous research has revealed that passive (involuntary inhalation) tobacco smoking during gestation can have adverse effects upon the developing fetus. These prior investigations did not concentrate on changes in fetal morphology. This study was undertaken to delineate fetal neural abnormalities at the ultrastructural level in mice pups exposed in utero to passive maternal smoking.Pregnant study animals, housed in a special chamber, were subjected to cigarette smoke daily from conception until delivery. Blood tests for determination of carbon monoxide levels were run at 15-18 days gestation. Sciatic nerve tissue from experimental and control animals were obtained following spontaneous delivery and fixed in 2.5% gluteraldehyde in 0.1M cacodylate buffer pH 7.3. The samples were post-fixed in osmium ferrocyanide (1:1 mixture of 1.5% aqueous OSO4 and 2.5% K4 Fe(CN)6). Following dehydration, the tissues were infiltrated with and embedded in Spurr. Sections were stained with uranyl acetate and lead citrate.

Application of EDS Technique for OSP Film Thickness Measurement

2006 ◽  
Author(s):  
Prong Kongsubto ◽  
Sirarat Kongwudthiti
Keyword(s):  
Thin Film ◽  
Quantitative Analysis ◽  
Joint Strength ◽  
Critical Factor ◽  
Thickness Measurement ◽  
Ic Manufacturing ◽  
And Control ◽  
Film Thickness Measurement ◽  
Non Destructive

Abstract Organic solderability preservatives (OSPs) pad is one of the pad finishing technologies where Cu pad is coated with a thin film of an organic material to protect Cu from oxidation during storage and many processes in IC manufacturing. Thickness of OSP film is a critical factor that we have to consider and control in order to achieve desirable joint strength. Until now, no non-destructive technique has been proposed to measure OSP thickness on substrate. This paper reports about the development of EDS technique for estimating OSP thickness, starting with determination of the EDS parameter followed by establishing the correlation between C/Cu ratio and OSP thickness and, finally, evaluating the accuracy of the EDS technique for OSP thickness measurement. EDS quantitative analysis was proved that it can be utilized for OSP thickness estimation.

scholarly journals Biodegradation of Poly(Lactic Acid) Biocomposites under Controlled Composting Conditions and Freshwater Biotope

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 594
Author(s):  
Pavel Brdlík ◽  
Martin Borůvka ◽  
Luboš Běhálek ◽  
Petr Lenfeld
Keyword(s):  
Degradation Rate ◽  
Poly Lactic Acid ◽  
Screw Extruder ◽  
Flat Film ◽  
Twin Screw ◽  
Acetyl Tributyl Citrate ◽  
And Control ◽  
Aerobic Biodegradability ◽  
Qualitative Analyses

The influence of additives such as natural-based plasticiser acetyl tributyl citrate (ATBC), CaCO3 and lignin-coated cellulose nanocrystals (L-CNC) on the biodegradation of polylactic acid (PLA) biocomposites was studied by monitoring microbial metabolic activity through respirometry. Ternary biocomposites and control samples were processed by a twin-screw extruder equipped with a flat film die. Commonly available compost was used for the determination of the ultimate aerobic biodegradability of PLA biocomposites under controlled composting conditions (ISO 14855-1). In addition, the hydro-degradability of prepared films in a freshwater biotope was analysed. To determine the efficiency of hydro-degradation, qualitative analyses (SEM, DSC, TGA and FTIR) were conducted. The results showed obvious differences in the degradation rate of PLA biocomposites. The application of ATBC at 10 wt.% loading increased the biodegradation rate of PLA. The addition of 10 wt.% of CaCO3 into the plasticised PLA matrix ensured an even higher degradation rate at aerobic thermophilic composting conditions. In such samples (PLA/ATBC/CaCO3), 94% biodegradation in 60 days was observed. In contrast, neat PLA exposed to the same conditions achieved only 16% biodegradation. Slightly inhibited microorganism activity was also observed for ternary PLA biocomposites containing L-CNC (1 wt.% loading). The results of qualitative analyses of degradation in a freshwater biotope confirmed increased biodegradation potential of ternary biocomposites containing both CaCO3 and ATBC. Significant differences in the chemical and structural compositions of PLA biocomposites were found in the evaluated period of three months.

Investigation of Impact Profile and Isolation Effect in Automated Impact Device Design and Control for Operational Modal Analysis

2015 ◽  
Vol 137 (9) ◽  
Author(s):  
Z. C. Ong ◽  
C. C. Lee
Keyword(s):  
Modal Analysis ◽  
Isolation Effect ◽  
Time Averaging ◽  
Impact Device ◽  
Lack Of Information ◽  
Analysis Technique ◽  
And Control ◽  
Phase Angles ◽  
Synchronous Time

A novel modal analysis technique called impact-synchronous modal analysis (ISMA) was introduced in previous research. With the utilization of impact-synchronous time averaging (ISTA), this modal analysis can be performed in presence of ambient forces whereas the conventional analysis method requires machines to be totally shut down. However, lack of information of phase angles with respect to impact in ISMA has caused it to be labor-intensive and time-consuming. An automated impact device (AID) is introduced in this study in the effort to replace the manually operated impact hammer and prepare it to be used in the current practice of ISMA on the purpose of enhancing its effectiveness and practicability. Impact profile and isolation effect are noted to be the contributing parameters in this study. This paper devoted on calibrating and controlling of the AID which gives the desired impact profiles as compared to the manual impact hammer. The AID is found effective in the determination of dynamic characteristics when the device is isolated from the boundary condition of the test structure.

Characterization and Control of Copper CMP with Optoacoustic Metrology

2001 ◽  
Vol 671 ◽  
Author(s):  
Michael Gostein ◽  
Paul Lefevre ◽  
Alex A. Maznev ◽  
Michael Joffe
Keyword(s):  
Film Thickness ◽  
Spatial Resolution ◽  
Chemical Mechanical Polishing ◽  
High Spatial Resolution ◽  
Mechanical Polishing ◽  
Length Measurement ◽  
And Control ◽  
Non Destructive

ABSTRACTWe discuss applications of optoacoustic film thickness metrology for characterization of copper chemical-mechanical polishing (CMP). We highlight areas where the use of optoacoustics for CMP characterization provides data complementary to that obtained by other techniques because of its ability to directly measure film thickness with high spatial resolution in a rapid, non-destructive manner. Examples considered include determination of planarization length, measurement of film thickness at intermediate stages of polish, and measurement of arrays of metal lines.

The Construction of Engineering Projects Environmental Performance Auditing

2013 ◽  
Vol 834-836 ◽  
pp. 2045-2048
Author(s):  
Xiao Ning Qu
Keyword(s):  
Environmental Performance ◽  
Internal Audit ◽  
Engineering Project ◽  
Whole Process ◽  
Social Audit ◽  
Multi Level ◽  
Performance Auditing ◽  
And Control ◽  
The Impact ◽  
Engineering Projects

The Environmental performance auditing is one professional audit that auditing the environmental performance of engineering project. We construct a multi-level auditing network in the whole process of project. That network can be divided into government audit, social audit and internal audit. And with which we predict, evaluate and control the impact on environmental effectively.

scholarly journals Superconductor qubits hamiltonian approximations effect on quantum state evolution and control

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Javad Sharifi
Keyword(s):  
Quantum State ◽  
Charge Qubit ◽  
Gate Operation ◽  
Goal State ◽  
Expected Time ◽  
State Evolution ◽  
Angle Of Deviation ◽  
Hadamard Gate ◽  
Phase Qubit ◽  
And Control

AbstractMicrowave IQ-mixer controllers are designed for the three approximated Hamiltonians of charge, phase and flux qubits and the controllers are exerted both on approximate and precise quantum system models. The controlled qubits are for the implementation of the two quantum-gates with these three fundamental types of qubits, Quantum NOT-gate and Hadamard-gate. In the charge-qubit, for implementation of both gates, in the approximated and precise model, we observed different controlled trajectories. But fortunately, applying the controller designed for the approximated system over the precise system leads to the passing of the quantum state from the desired state sooner that the expected time. Phase-qubit and flux qubit have similar behaviour under the control system action. In both of them, the implementation of NOT-gate operation led to same trajectories which arrive at final goal state at different times. But in both of those two qubits for implementation of Hadamard-gate, desired trajectory and precise trajectory have some angle of deviation, then by exerting the approximated design controller to precise system, it caused the quantum state to approach the goal state for Hadamard gate implementation, and since the quantum state does not completely reach the goal state, we can not obtain very high gate fidelity.

Sign in / Sign up

Export Citation Format

Share Document