scholarly journals New Mass Model FRDM 2012 and Symmetry Energy

2017 ◽  
Author(s):  
Hiroyuki Sagawa ◽  
Peter Möller
Keyword(s):  
Symmetry Energy ◽  
Mass Model

Study of the dynamics of ТПА 350 automatic mill working stand elements

2020 ◽  
Vol 76 (8) ◽  
pp. 830-840
Author(s):  
S. R. Rakhmanov ◽  
V. V. Povorotnii
Keyword(s):  
Mechanical System ◽  
Dynamic Model ◽  
Maximum Amplitude ◽  
Calculation Scheme ◽  
Dynamic Loads ◽  
Forced Oscillations ◽  
Mass Model ◽  
Automatic Mill ◽  
Hollow Billet ◽  
Oscillation Movement

To form a necessary geometry of a hollow billet to be rolled at a pipe rolling line, stable dynamics of the base equipment of the automatic mill working stand has a practical meaning. Among the forces, acting on its parts and elements, significant by value short-time dynamic loads are the least studied phenomena. These dynamic loads arise during transient interaction of the hollow billet, rollers, mandrel and other mill parts at the forced grip of the hollow billet. Basing of the calculation scheme and dynamic model of the mechanical system of the ТПА 350 automatic mill working stand was accomplished. A mathematical model of dynamics of the system “hollow billet (pipe) – working stand” within accepted calculation scheme and dynamic model of the mechanical system elaborated. Influence of technological load of the rolled hollow billet variation in time was accounted, as well as variation of the mechanical system mass, and rigidity of the ТПА 350 automatic mill working stand. Differential equations of oscillation movement for four-mass model of forked sub-systems of the automatic mill working stand were made up, results of their digital calculation quoted. Dynamic displacement of the stand elements in the inter-roller gap obtained, which enabled to estimate the results of amplitude and frequency characteristics of the branches of the mill rollers setting. It was defined by calculation, that the maximum amplitude of the forced oscillations of elements of the ТПА 350 automatic mill working stand within the inter-roller gap does not exceed 2 mm. It is much higher than the accepted value of adjusting parameters of the deformation center of the ТПА 350 automatic mill. A scheme of comprehensive modernization of the rollers setting in the ТПА 350 automatic mill working stand was proposed. It was shown, that increase of rigidity of rollers setting in the ТПА 350 automatic mill working stand enables to stabilize the amplitude of forced oscillations of the working stand elements within the inter-rollers gap and considerably decrease the induced nonuniform hollow billet wall thickness and increase quality of the rolled pipes at ТПА 350.

Growth Kinetics of Quantum Size ZnO Particles

1998 ◽  
Vol 536 ◽  
Author(s):  
E. M. Wong ◽  
J. E. Bonevich ◽  
P. C. Searson
Keyword(s):  
Growth Kinetics ◽  
Ostwald Ripening ◽  
Chemical Potential ◽  
Colloidal Suspensions ◽  
Green Emission ◽  
Blue Shift ◽  
Constant Current ◽  
Mass Model ◽  
Zno Particles ◽  
Kinetics Of

AbstractColloidal chemistry techniques were used to synthesize ZnO particles in the nanometer size regime. The particle aging kinetics were determined by monitoring the optical band edge absorption and using the effective mass model to approximate the particle size as a function of time. We show that the growth kinetics of the ZnO particles follow the Lifshitz, Slyozov, Wagner theory for Ostwald ripening. In this model, the higher curvature and hence chemical potential of smaller particles provides a driving force for dissolution. The larger particles continue to grow by diffusion limited transport of species dissolved in solution. Thin films were fabricated by constant current electrophoretic deposition (EPD) of the ZnO quantum particles from these colloidal suspensions. All the films exhibited a blue shift relative to the characteristic green emission associated with bulk ZnO. The optical characteristics of the particles in the colloidal suspensions were found to translate to the films.

scholarly journals Comparative Analysis of Identification Methods for Mechanical Dynamics of Large-Scale Wind Turbine

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3429 ◽  
Author(s):  
Chu ◽  
Yuan ◽  
Hu ◽  
Pan ◽  
Pan
Keyword(s):  
Mutual Information ◽  
Parameter Identification ◽  
Wind Turbines ◽  
Closed Loop ◽  
Control Design ◽  
Identification Accuracy ◽  
Mass Model ◽  
Identification Methods ◽  
Advanced Control ◽  
Mechanical Dynamics

With increasing size and flexibility of modern grid-connected wind turbines, advanced control algorithms are urgently needed, especially for multi-degree-of-freedom control of blade pitches and sizable rotor. However, complex dynamics of wind turbines are difficult to be modeled in a simplified state-space form for advanced control design considering stability. In this paper, grey-box parameter identification of critical mechanical models is systematically studied without excitation experiment, and applicabilities of different methods are compared from views of control design. Firstly, through mechanism analysis, the Hammerstein structure is adopted for mechanical-side modeling of wind turbines. Under closed-loop control across the whole wind speed range, structural identifiability of the drive-train model is analyzed in qualitation. Then, mutual information calculation among identified variables is used to quantitatively reveal the relationship between identification accuracy and variables’ relevance. Then, the methods such as subspace identification, recursive least square identification and optimal identification are compared for a two-mass model and tower model. At last, through the high-fidelity simulation demo of a 2 MW wind turbine in the GH Bladed software, multivariable datasets are produced for studying. The results show that the Hammerstein structure is effective for simplify the modeling process where closed-loop identification of a two-mass model without excitation experiment is feasible. Meanwhile, it is found that variables’ relevance has obvious influence on identification accuracy where mutual information is a good indicator. Higher mutual information often yields better accuracy. Additionally, three identification methods have diverse performance levels, showing their application potentials for different control design algorithms. In contrast, grey-box optimal parameter identification is the most promising for advanced control design considering stability, although its simplified representation of complex mechanical dynamics needs additional dynamic compensation which will be studied in future.

The nuclear symmetry energy in relativistic Brueckner-Hartree-Fock calculations

1987 ◽  
Vol 199 (4) ◽  
pp. 469-474 ◽  
Author(s):  
H. Müther ◽  
M. Prakash ◽  
T.L. Ainsworth
Keyword(s):  
Symmetry Energy ◽  
Nuclear Symmetry Energy ◽  
Hartree Fock

Simulated synchrotron emission for the Tycho’s supernova remnants: an asymmetric initial mass model

2020 ◽  
Vol 494 (2) ◽  
pp. 1531-1538
Author(s):  
A Moranchel-Basurto ◽  
P F Velázquez ◽  
G Ares de Parga ◽  
E M Reynoso ◽  
E M Schneiter ◽  
...  
Keyword(s):  
Supernova Remnants ◽  
Brightness Distribution ◽  
Radio Continuum ◽  
Initial Mass ◽  
Continuum Emission ◽  
Synchrotron Emission ◽  
Mass Model ◽  
Mhd Simulations ◽  
Tycho’S Snr ◽  
Good Agreement

ABSTRACT We have performed 3D magnetohydrodynamics (MHD) numerical simulations with the aim of exploring the scenario in which the initial mass distribution of a supernova (SN) explosion is anisotropic. The purpose is to analyse if this scenario can also explain the radio-continuum emission and the expansion observed in young supernova remnants (SNRs). To study the expansion, synthetic polarized synchrotron emission maps were computed from the MHD simulations. We found a good agreement (under a number of assumptions) between this expansion study and previous observational results applied to Tycho’s SNR, which represents a good example of asymmetric young SNRs. Additionally, both the observed morphology and the brightness distribution are qualitatively reproduced.

scholarly journals The AstroSat mass model: Imaging and flux studies of off-axis sources with CZTI

2021 ◽  
Vol 42 (2) ◽  
Author(s):  
Sujay Mate ◽  
Tanmoy Chattopadhyay ◽  
Varun Bhalerao ◽  
E. Aarthy ◽  
Arvind Balasubramanian ◽  
...  
Keyword(s):  
Mass Model

scholarly journals Fault Diagnosis of Brake Train Based on Multi-Sensor Data Fusion

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4370
Author(s):  
Yongze Jin ◽  
Guo Xie ◽  
Yankai Li ◽  
Xiaohui Zhang ◽  
Ning Han ◽  
...  
Keyword(s):  
Fault Diagnosis ◽  
Expectation Maximization ◽  
Monitoring Data ◽  
Sensor Data ◽  
Operating Environment ◽  
Mass Model ◽  
Multi Sensor Data Fusion ◽  
Diagnosis Method ◽  
Single Mass ◽  
Parameter Identifications

In this paper, a fault diagnosis method is proposed based on multi-sensor fusion information for a single fault and composite fault of train braking systems. Firstly, the single mass model of the train brake is established based on operating environment. Then, the pre-allocation and linear-weighted summation criterion are proposed to fuse the monitoring data. Finally, based on the improved expectation maximization, the braking modes and braking parameters are identified, and the braking faults are diagnosed in real time. The simulation results show that the braking parameters of systems can be effectively identified, and the braking faults can be diagnosed accurately based on the identification results. Even if the monitoring data are missing or abnormal, compared with the maximum fusion, the accuracies of parameter identifications and fault diagnoses can still meet the needs of the actual systems, and the effectiveness and robustness of the method can be verified.

Sign in / Sign up

Export Citation Format

Share Document