scholarly journals Effect of fiber amount on properties of polypropylene fiber reinforced roller compacted concrete

2021 ◽  
Vol 20 (2) ◽  
pp. 205-214
Author(s):  
Ismail Kilic ◽  
◽  
Saadet Gokce Gok ◽  
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Building Materials ◽  
Construction Material ◽  
Polypropylene Fiber ◽  
Pulse Velocity ◽  
Unit Weight ◽  
Fiber Reinforced ◽  
Freeze Thaw ◽  
Roller Compacted Concrete

Roller compacted concrete (RCC) is a relatively new alternative construction material that can be used in road and dam constructions by allowing rapid use after production and the use of conventional building materials in production. RCC, which can be produced with low water/cement ratio, is one of the rigid road pavement types and shows similarity to flexible road pavements with the production technique. Different types of fibers such as steel and polypropylene (PP) are used in concrete roads with the aim of preventing cracks, reducing the pavement thickness and increasing the permissible joint gap. In this study, flexural strength, compressive strength, unit weight, water absorption, ultrasonic pulse velocity, modulus of elasticity and freeze-thaw resistance were determined in roller compacted concretes produced by using two different polypropylene-based fibers. In RCC design, fiber addition was insufficient to improve concrete properties in terms of strength and durability. It has been observed that there was a 14.4% reduction in compressive strength with 0.20% fiber inclusion, and a 46.8% reduction in compressive strength with 0.50% fiber inclusion. Polypropylene fiber inclusion increased the water absorption percentages and decreased the specific weights of fiber reinforced roller compacted concretes. However, roller compacted concretes produced with PP-fiber exhibited a good performance under freeze-thaw attack.

scholarly journals The effects of adding waste plastic fibers on some properties of roller compacted concrete

2018 ◽  
Vol 162 ◽  
pp. 02008 ◽  
Author(s):  
Adil Abed ◽  
Abdulkader Al-Hadithi ◽  
Ahmed Salih Mohammed
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
Design Method ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Dry Density ◽  
Waste Plastic ◽  
Roller Compacted Concrete

An attempt to produce of roller compacted concrete (RCC) improved by adding waste plastic fibers (WPFs) resulting from cutting the PET beverage bottles was recorded in this study. The method which is used for production of RCC is an approved design method for ACI committee (5R-207,1980)[1]. WPF was added by volumetric percentages ranging between (0.5 to 2 %) and reference concrete mix was produced for comparison reason. Many tests were conducted on the models produced by rolling compacted concrete like compressive strength, flexural strength, modulus of elasticity, dry density, water absorption and ultrasonic pulse velocity. The analysis of the results showed that the use of plastic waste fibers (1%) had led to improvement in the properties of each of the compressive strength and flexural strength compared with reference concrete. Results also showed that the addition of these, fibers increase water absorption and reduce the speed of Ultrasonic pulse velocity.

Recycling of Crushed Clay Brick as Aggregate in Concrete

2011 ◽  
Vol 94-96 ◽  
pp. 1087-1090 ◽  
Author(s):  
Hamed Nabizadeh Rafsanjani ◽  
Morteza Chehreghani ◽  
Mohsen Nourbakhsh
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Environmental Problem ◽  
Construction Material ◽  
Construction Project ◽  
Unit Weight ◽  
Clay Brick ◽  
New Material ◽  
Compressive Strength Of Concrete

Clay brick generated from construction project sites is usually delivered to landfills for disposal and thus they can damage environment. The use of crushed clay brick can solve the environmental problem. This paper presents the possible use of crushed clay brick as a construction material. This new material gathered from some construction project sites in Iran is used as 100% aggregate in the production of concrete. The results indicated that the crushed clay brick reduced the unit weight and compressive strength of concrete, and increase the water absorption value. This new concrete can be used in non-structural products.

Testing on Building Material Using Waste Material in Fired Clay Brick

2014 ◽  
Vol 803 ◽  
pp. 330-336 ◽  
Author(s):  
A.A. Kadir ◽  
Noor Amira Sarani ◽  
A.M. Leman
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Building Materials ◽  
Construction Material ◽  
Calorific Value ◽  
Waste Material ◽  
Dry Density ◽  
Clay Brick ◽  
Heating Rates ◽  
Cigarette Butts

Clay brick is one of the building materials that have been used in the construction field for thousand years. It has been used as a major construction material because it can tolerate with severe weathering action, flexible properties and it is easy to handle. Many researchers have been incorporated waste material such as organic waste, waste treatment sludge, fly ash, cigarette butts, rice husk and processed waste tea into fired clay brick. This application gives an idea to use waste material that will give a minimum impact to the real environment. In this study, high calorific value waste such as cigarette butts (CBs) were incorporated into fired clay brick. Different percentages of CBs (0%, 2.5% and 5.0%) were added into the raw clay brick. All samples were fired up to 1050°C with different heating rates (1°C/min, 3°C/min and 5°C/min). Properties including compressive strength, dry density, firing shrinkage and water absorption are reported and discussed. The results show that the compressive strength of fired clay brick was obtained with 2.5% CBs of fired clay brick at 1°C/min heating rate compared to others. As for the density, it was reduced with higher percentages of CBs incorporated into the raw clays. From the results, water absorption was slightly increased when CBs were incorporated into clay brick. The results suggested that heating rates at 1oC/min is adequate to achieve optimum properties.

scholarly journals Cost Optimization of Mortars Containing Different Pigments and Their Freeze-Thaw Resistance Properties

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Sadık Alper Yıldızel ◽  
Gökhan Kaplan ◽  
Ali Uğur Öztürk
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Pore Structure ◽  
Water Absorption ◽  
Cost Optimization ◽  
Unit Weight ◽  
Concrete Construction ◽  
Freeze Thaw ◽  
White Cement ◽  
Architectural Mortar

Nowadays, it is common to use colored concrete or mortar in prefabricated concrete and reinforced concrete construction elements. Within the scope of this study, colored mortars were obtained with the addition of brown, yellow, black, and red pigments into the white cement. Those mixtures are examined for their compressive strength, unit weight, water absorption, and freeze-thaw resistance. Subsequent to comparison of these properties, a cost optimization has been conducted in order to compare pigment costs. The outcomes showed that the pore structure in architectural mortar applications plays an important role in terms of durability. And cost optimization results show that light colored minerals can be used instead of white cements.

scholarly journals Influence of the Fiber Volume Content on the Durability-Related Properties of Polypropylene-Fiber-Reinforced Concrete

2020 ◽  
Vol 12 (2) ◽  
pp. 549
Author(s):  
Chenfei Wang ◽  
Zixiong Guo ◽  
Ditao Niu
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Volume Content ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Freeze Thaw ◽  
Chloride Environment ◽  
Polypropylene Fiber Reinforced Concrete

Polypropylene-fiber-reinforced concrete impacts the early shrinkage during the plastic stage of concrete, and the fiber volume content influences the durability-related properties of concrete. The purpose of this paper was to investigate the influence of fiber volume content on the mechanical properties, durability, and chloride ion penetration of polypropylene-fiber-reinforced concrete in a chloride environment. Tests were carried out on cubes and cylinders of polypropylene-fiber-reinforced concrete with polypropylene fiber contents ranging from 0% to 0.5%. Extensive data from flexural strength testing, dry–wet testing, deicer frost testing, and chloride penetration testing were recorded and analyzed. The test results show that the addition of the fiber improves the failure form of the concrete specimens, and 0.1% fiber content maximizes the compactness of the concrete. The flexural strength of specimen C2 with 0.1% fiber shows the highest strength obtained herein after freeze–thaw cycling, and the water absorption of specimen C2 is also the lowest after dry–wet cycling. The results also indicate that increasing the fiber volume content improves the freeze–thaw resistance of the concrete in a chloride environment. Chlorine ions migrate with the moisture during dry–wet and freeze–thaw cycling. The chlorine ion diffusion coefficient (Dcl) increases with increasing fiber content, except for that of specimen C2 in a chloride environment. The Dcl during freeze–thaw cycling is much higher than that during dry–wet cycling.

scholarly journals OPTIMUM PERFORMANCE OF STABILIZED EDE LATERITE AS AN ALTERNATIVE CONSTRUCTION MATERIAL

2020 ◽  
Vol 3 (8) ◽  
pp. 1-8
Author(s):  
Adegbenle Bukunmi O
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Construction Material ◽  
High Water ◽  
Good Alternative ◽  
Linear Shrinkage ◽  
Absorption Capacity ◽  
Water Absorption Capacity ◽  
Optimum Performance ◽  
High Water Absorption

Laterite samples from Ede area with particle components of 19.7% clay, 32.8% silt and 47.5% sand was stabilized with combined cement, lime and bitumen and test for Compressive strength, Linear Shrinkage, Permeability and Water Absorption. The stabilizers were mixed with laterite soil in different ratios and percentage. The laterite carried 90% which is constant while the three stabilizers shared the remaining 10% in varying form. After 28 days of curing, laterite stabilizer with 90% of laterite, 8% of cement, 1% lime and 1% bitumen (LCLB1) possessed compressive strength of 2.01N/mm2. It Water Absorption Capacity was 3.05%. LCLB4 stabilizer (90% laterite, 6% cement, 2% lime and 2% bitumen) has the same compressive strength with LCLB1 stabilizer but with a high Water Absorption Capacity of 4.2%. The stabilizer of 90% laterite, 3.33% cement, 3.33% lime and 3.33% of bitumen (LCLB8) has the lowest compressive strength of 0.74N/mm2 and the highest Water Absorption Capacity of 5.39%. The results shows that LCLB1 stabilizer is a better stabilizer for strength and blocks made from laterite stabilized with it stand a good alternative to sand Crete blocks in building constructions. The combination of these stabilizers in order to determine a most economical volume combination for optimum performance is highly possible and economical.

scholarly journals The Effect of Polymer-Cement Stabilization on the Unconfined Compressive Strength of Liquefiable Soils

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Ali Ateş
Keyword(s):  
Compressive Strength ◽  
Compression Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Sandy Soils ◽  
Pulse Velocity ◽  
Unit Weight ◽  
Unconfined Compression Strength ◽  
Compression Tests ◽  
Unconfined Compression

Soil stabilization has been widely used as an alternative to substitute the lack of suitable material on site. The use of nontraditional chemical stabilizers in soil improvement is growing daily. In this study a laboratory experiment was conducted to evaluate the effects of waterborne polymer on unconfined compression strength and to study the effect of cement grout on pre-venting of liquefiable sandy soils. The laboratory tests were performed including grain size of sandy soil, unit weight, ultrasonic pulse velocity, and unconfined compressive strength test. The sand and various amounts of polymer (1%, 2%, 3%, and 4%) and cement (10%, 20%, 30%, and 40%) were mixed with all of them into dough using mechanical kneader in laboratory conditions. Grouting experiment is performed with a cylindrical mould of  mm. The samples were subjected to unconfined compression tests to determine their strength after 7 and 14 days of curing. The results of the tests indicated that the waterborne polymer significantly improved the unconfined compression strength of sandy soils which have susceptibility of liquefaction.

DURABILITY PERFORMANCE AND DIMENSIONAL STABILITY OF POLYPROPYLENE FIBER REINFORCED CONCRETE

2018 ◽  
Vol 13 (2) ◽  
pp. 20-41 ◽  
Author(s):  
Ali Mardani-Aghabaglou ◽  
Süleyman Özen ◽  
Muhammet Gökhan Altun
Keyword(s):  
Reinforced Concrete ◽  
Dimensional Stability ◽  
Polypropylene Fiber ◽  
Pulse Velocity ◽  
Fiber Reinforced Concrete ◽  
Concrete Mixture ◽  
Fiber Reinforced ◽  
Concrete Mixtures ◽  
Durability Performance ◽  
Polypropylene Fiber Reinforced Concrete

In this study, the durability performance and dimensional stability of polypropylene fiber reinforced concrete mixture were investigated. For this purpose, two series of concrete mixtures, including a 0.45 water/cement ratio was prepared both in the absence and presence of fiber. A CEMI 42.5 R type portland cement and crushed limestone aggregate with a maximum particle size of 25 mm were used. In addition to the control mixture without fiber, three different concrete mixtures were prepared by adding polypropylene fiber as 0.4%, 0.8% and 1% of total volume into the mixture. The time-dependent fresh state properties, strength, ultrasonic pulse velocity, transport properties, drying shrinkage and freeze-thaw resistance of concrete mixtures, sodium sulfate attack and abrasion were investigated comparatively. Test results demonstrated that utilization of fiber affected the fresh properties of the concrete mixtures negatively. However, the 0.8% fiber-bearing mixture showed the highest performance in terms of durability and dimensional stability. Beyond this utilization ratio, the durability performance of the concrete mixture was negatively affected. The risk of nonhomogeneous dispersion of the fiber in the mixture was relatively high in the excess fiber-bearing mixture. Consequently, with the formation of flocculation in the mixture the void ratio of concrete mixture increased.

scholarly journals Development and characterization of sustainable lightweight geopolymer composites

Cerâmica ◽  
2019 ◽  
Vol 65 (373) ◽  
pp. 153-161 ◽  
Author(s):  
H. M. Khater
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Aluminum Powder ◽  
Building Materials ◽  
Microstructural Characteristics ◽  
Imaging Results ◽  
Lightweight Composites ◽  
Sem Imaging ◽  
Geopolymer Composites

Abstract Production of lightweight building materials attract the attention of the scientists worldwide with the need for reducing the structure deadweight, provide better thermal insulation for buildings, and cost less to transport. The current work focused on the production of lightweight geopolymer composites by the incorporation of aluminum powder and aluminum slag in various ratios for water-cooled slag/kaolinite sand composite; the activators used were 6% of equal ratio from sodium hydroxide and sodium silicate. The properties of the produced lightweight geopolymer composites were studied by measurement of compressive strength, bulk density, water absorption, FTIR, XRD and SEM imaging. Results showed the enhancement for both physicomechanical and microstructural characteristics with using aluminum powder and aluminum slag forming lightweight composites with densities below 2.15 g/cm3 depending on the studied mix composition.

Sign in / Sign up

Export Citation Format

Share Document