scholarly journals A feasibility study on calcareous soil stabilization using polymers in Barka region.

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
S.V. Satyanarayana ◽  
Mohammed Al Jahwari
Keyword(s):  
Moisture Content ◽  
Bearing Capacity ◽  
Calcareous Soil ◽  
Soil Stabilization ◽  
Synthetic Polymer ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Atterberg Limit

In the Gulf region most of the soils require soil stabilization to increase soil bearing capacity for construction of safe and sustainable buildings. The soils are stabilized either by physical stabilization, chemical stabilization or by mechanical stabilization. The aim of this project is to stabilize calcareous soil in the Barka region with synthetic polymers. The soil samples from the Barka region collected by using standard soil sampling methods. The synthetic polymer was mixed with the calcareous soil in 1%, 3% and 5%. The soil samples were tested for sieve analysis, Atterberg Limit, Particle Density, Proctor test and California Bearing Ratio test before and after addition of synthetic polymer. It was observed that there is a positive impact on the geotechnical properties of soil with the addition of Polymer. The optimum moisture content of the soil reduced and the maximum dry density of the soil increased. The optimum results were found at 5% addition of polymer where the optimum moisture content was found out to be 12.6% and the maximum dry density was found out to be 1.997 Mg/m3. The Atterberg limit test to show that the plasticity index of the soil reduced with the addition of polymer and the optimum results were found out at 5% addition of polymer. Finally, the CBR test results determine that the soil bearing capacity increases with the addition of Polymer. After the addition of 5% Polymer, the CBR value was found out to be 27.465% compared to 14.19% for the fresh calcareous soil. The results are encouraging. Keywords: Atterberg Limit, Calcareous soil, CBR, polymer, stabilization.

scholarly journals Engineering behaviour of stabilized laterite and kaolin using lignin

2018 ◽  
Vol 250 ◽  
pp. 01008
Author(s):  
Tuan Noor Hasanah Tuan Ismail ◽  
Siti Aimi Nadia Mohd Yusoff ◽  
Ismail Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
...  
Keyword(s):  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Laboratory Tests ◽  
Dry Weight ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Laterite Soil ◽  
Maximum Dry Density ◽  
Steady Rate

Soils at many sites do not always have enough strength to bear the structures constructed over them and some of the soil may need to be stabilized in order to improve their geotechnical properties. In this paper, routine laboratory tests were critically carried out to investigate the efficacy of lignin in improving the strength behaviour of the soils. Two different soil samples (laterite and kaolin) were studied and mixed with different proportions of lignin (2% and 5% of dry weight of soil), respectively. Unconfined Compressive Strength (UCS) characteristics evaluated in this study were done on samples at their maximum dry density and optimum moisture content (obtained from compaction tests). The UCS tests on all the specimens were carried out after 0, 7, 15, 21 and 30 days of controlled curing. The research results showed that the addition of lignin into kaolin reduced its maximum dry density while giving progressively higher optimum moisture content. Contrarily, with the laterite soil, both maximum dry density and optimum moisture content simultaneously increased when lignin was added into the soils. The UCS results showed that the the stabilized laterite with 2% lignin continued to gain strength significantly at a fairly steady rate after 7 days. Unfortunately, lignin did not show a significant effect in kaolin.

Assessment of Gneiss-Derived Residual Soils as Materials Used in Road Pavement Structures

2020 ◽  
Vol 3 ◽  
pp. 12-25
Author(s):  
Olaoluwa Oluwaniyi ◽  
Imoleayo Fatoyinbo ◽  
Akinola Bello ◽  
Joshua Owoseni
Keyword(s):  
Moisture Content ◽  
Linear Shrinkage ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Residual Soils ◽  
Maximum Dry Density ◽  
Road Pavement ◽  
Natural Moisture Content ◽  
Pavement Structures

Failure of highway pavement and collapse of building in basement complex of Nigeria is often related to the instability of the residual. This study evaluated the strength characteristics of gneiss-derived residual Soils as materials usable for road pavement structures. A total of eleven soil samples derived from granite gneiss were subjected to laboratory geotechnical analyses based on standard practices. The geotechnical analyses reveal the soils’ natural moisture content, specific gravity, grain sizes, consistency limits, shearing strengths, maximum dry density, and optimum moisture content. Based on AASHTO classification, the soil samples are classified as A-7-6, A-6, and A-7-5. The results of the laboratory analyses revealed that the natural moisture content and specific gravity ranged from 8.30 to 22.70% and 2.6 to 2.8 respectively. Particle size analysis reveals that the coarse contents of the soils ranged from 28.8% to 59.8% and amount of fines ranged from 40.2 to 71.2%. The liquid limit ranged from 31.3% to 68.3%, plastic limit ranged from 20% to 28.0%, plasticity index ranged from 4.8% to 38.90% and linear shrinkage ranged from 5.7 to 13.6%. The maximum dry density ranged from 1481 kg/m3 to 1921 kg/m3 and optimum moisture content ranged from 15.2% to 27.6%. Undrained triaxial shear strength (Cu) ranged from 43.0 Kpa to 250.3Kpa, angle of friction ranges from 11.7 to 29.30, and unconfined compressive strength ranged from 153 to 356.5Kpa. The results indicate that the residual soils are poor sub-grade and foundation materials due to their high amount of fines, linear shrinkage values, plasticity, and swelling potential, as well as low maximum dry density.

scholarly journals Evaluation of Bentonite Mixed Indigenous Clays for Development of Clay Liners

2020 ◽  
Vol 6 ◽  
pp. 24-32
Author(s):  
Muhammad Israil ◽  
Muhammad Ashraf ◽  
Muhammad Fahim ◽  
Rashid Rehan ◽  
Sajjad Wali Khan ◽  
...  
Keyword(s):  
Hydraulic Conductivity ◽  
Specific Gravity ◽  
Moisture Content ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Atterberg Limits ◽  
Dry Density ◽  
Clay Liners ◽  
Maximum Dry Density ◽  
Free Swell

This study presents experimental investigation of indigenous clays mixed with Bentonite to assess their suitability in potential use as clay liners. Soil samples with 0, 4, 8, and 12% Bentonite content from three different sites in Peshawar region were tested for various geotechnical properties. Grain size distribution, specific gravity, Atterberg limits and free swell were found through laboratory tests using appropriate ASTM procedures. Maximum dry density and optimum moisture content were calculated using Atterberg limits in available relationships. Finally, one dimensional consolidation tests were conducted to find relevant parameters for calculating hydraulic conductivity. A decrease in specific gravity, increase in free swell, and in optimum moisture content, decline in maximum dry density and hydraulic conductivity was observed with increase in Bentonite content across all three soil samples. During free swell, the soil clusters become larger leading to formation of floccules resulting in the narrowing of inter-particle space and thus blocking of permeable paths. It is concluded that 8% Bentonite content by weight yields a suitable mixture for a clay liner that has hydraulic conductivity in the range of recommended limits.

A Study of Soil Stabilization by Hydrated Lime at Kampung Kedaik Asal, Rompin, Pahang, Malaysia

2014 ◽  
Vol 695 ◽  
pp. 738-741
Author(s):  
Azhani Zukri ◽  
Nadiatul Adilah Ahmad Abdul Ghani
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Optimum Moisture Content ◽  
Natural State ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Lime Content ◽  
Curing Period

This study involves the clay sample which is taken from Kampung Kedaik Asal, Rompin site and evaluation of its properties in natural state and after stabilization. The main objectives of this paper is to estimate the optimum lime content (OLC) needed to stabilize the soil by using Eades-Grim pH Test, to determine the optimum moisture content (OMC) and maximum dry density (MDD) of the treated soil by Standard Proctor Test and also the strength value of the soil specimens with different percentages of lime content corresponding with different curing period by Unconfined Compressive Strength (UCS) Test. From this study, the optimum amount to stabilize the clay soil and minimum amount of lime required to stabilize the soil pH level to 12 is 5%. The results showed that addition of lime decreased the maximum dry density (MDD) and increased the optimum moisture content (OMC). Unconfined compressive test on 48 sets of samples has been carried out for 7, 14 and 28 days of curing with different lime contents such as 5%, 7% and 9%. The highest unconfined compressive strength (UCS) achieved is 321 kN/m2 for clay stabilized with 9% lime content cured at 28 days. From the test results, it was found that the longer the immersion of curing period with higher lime content, the greater the compressive strength of the specimen.

scholarly journals Influence of Waste Marble Dust on the Improvement of Expansive Clay Soils

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Hassan A. M. Abdelkader ◽  
Mohamed M. A. Hussein ◽  
Haiwang Ye
Keyword(s):  
Moisture Content ◽  
Soil Stabilization ◽  
Clayey Soil ◽  
Expansive Soil ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Expansive Clay ◽  
Maximum Dry Density ◽  
Marble Dust ◽  
Soil Mixtures

The marble process industry from Shaq Al-Thouban region, which is located in East Cairo, Egypt, produces a huge amount of marble wastes every day during the cutting and processing stages. Up to now, most of these wastes are dumping on open land which creates serious environmental problems. The amount of waste marble from the processing stage is about 20 to 25% of the total processed stone. Egypt also suffers from the problem of expansive soil that occupies a large area of its lands, especially in the new cities that are built on these lands. The primary purpose of this study is to use this waste material in the soil stabilization in point of view utilization of this waste as local low-cost materials and elimination of their negative environmental impacts. The waste marble dust was mixed with expansive soil samples with various percentages of 5%, 10%, 15%, 20%, and 25% by dry weight of soil. Different tests including Atterberg’s limits, standard Proctor compaction, unconfined compressive strength (UCS), California bearing ratio (CBR), swelling percentage, linear shrinkage (LS) tests, and XRF and XRD analyses were conducted for natural and marble dust stabilized soils. The soil mixtures used for UCS, CBR, and swell tests were compacted at the optimum moisture content (OMC) and maximum dry density (MDD) using the standard Proctor compaction method and cured for 7 days. The results of the tests showed that there are significant effects in enhancing the properties of expansive soils. Also, the results showed that as the percentage of the marble dust increases the plasticity index, the swelling potential of the expansive clayey soil decreases. Furthermore, the optimum moisture content decreases, and the maximum dry density increases. Also, UCS, CBR, and the calcite content of the soil mixtures increase with the increase in marble dust content.

scholarly journals A study on the correlation potential of compaction characteristics and atterberg limits of selected lateritic soils

2020 ◽  
Vol 8 (1) ◽  
pp. 22
Author(s):  
G.O Adunoye ◽  
A.A Ojo ◽  
A.F Alasia ◽  
M.O Olarewaju
Keyword(s):  
Moisture Content ◽  
Liquid Limit ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Atterberg Limits ◽  
Dry Density ◽  
Plastic Limit ◽  
Maximum Dry Density ◽  
Compaction Characteristics ◽  
Correlation Potential

The importance of soil compaction for civil engineering construction and application cannot be over-emphasised. To perform soil compaction, numerous number of samples are required, with considerable time and laborious laboratory activities. This has necessitated the need to find models for the prediction of compaction characteristics, using easily determined soil properties. This work therefore undertook a study of the correlation potential of compaction characteristics and Atterberg limits of soils, with a view to modelling compaction characteristics, using Atterberg limits. To achieve this aim, soil samples were obtained from selected locations within Obafemi Awolowo University campus, Ile-Ife, Nigeria. Preliminary, Atterberg limits and compaction tests were conducted on the soil samples, using standard procedure. Using Microsoft Excel and Xuru’s Regression tool, the laboratory test results were used to develop relationships between compaction characteristics (optimum moisture content and maximum dry density) and Atterberg limits (liquid limit and plastic limit). Results showed that the natural moisture content of soil samples ranged between 4.97 % and 19.72 %; liquid limit ranged between 27 % and 68 %; plastic limit ranged between 18.92 % and 63.01 %; and plasticity index ranged between 0.94 % and 14.63 %. The optimum moisture content ranged between 6.7 % and 27 %, while the maximum dry density ranged between 1560 kN/m3 and 2260 kN/m3. The results of regression analysis showed that the combination of liquid limit and plastic limit has a strong correlation with optimum moisture content (R2 = 0.870); while the combination (of liquid limit and plastic limit) showed a weak correlation with maximum dry density (R2 = 0.150). The study concluded that liquid limit and plastic limit could be used to estimate the optimum moisture content of the soils, by applying the developed relationship/equation.  

scholarly journals Effect of Sand Percentage on the Compaction Properties and Undrained Shear Strength of Low Plasticity Clay

2021 ◽  
Vol 9 (1) ◽  
pp. 16-20
Author(s):  
Iyad Alkroosh ◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Sand Mixture ◽  
Undrained Shear

This paper investigates the influence of sand content on the mechanical behavior of a low plasticity clay that collected from south of Iraq (Sumer town). Samples have been prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the clay weight. Standard Proctor and unconfined compression tests have been carried out and the optimum moisture content, maximum dry density, and undrained shear strength have been determined. The results show a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reaches 1.90 g/cm3 corresponding to an optimum moisture content of 12%. In addition, this paper shows that the undrained shear strength is inversely proportional to the increase of the percentage of sand. The results of this work provide a useful addition to the literature regarding the behaviour or low plasticity clay-sand mixture.

Compaction Characteristic of Lime Modified Expansive Soil

2013 ◽  
Vol 710 ◽  
pp. 348-351
Author(s):  
Zheng Rong Zhao ◽  
Lei Wang ◽  
Hong Xia Yang
Keyword(s):  
Moisture Content ◽  
Expansive Soil ◽  
Size Composition ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Content Increase ◽  
Maximum Dry Density ◽  
Compaction Curve ◽  
Compaction Characteristic ◽  
Two Peaks

Through compaction test discussed about the compaction characteristics of expansive soil by lime modified in middle of Shandong province. The results show that the optimum moisture content is lower when the expansive soil is cured by dry compaction method, and the maximum dry density is higher. Compaction curve appeared the phenomenon of two peaks when expansive soil is cured by wet compaction method.Lime content of lime improved expansive soil, particle size composition, age and compaction function have influence on compaction curve.With the increase of the quantity of lime, the optimum moisture content increases, the maximum dry density decreases. With the age growth, the optimum moisture content increase slightly,the maximum dry density decreases slightly. The bigger the compaction work, the smaller moisture content is, the larger the maximum dry density is.

scholarly journals COMPACTION ASSESSMENT OF RECYCLED AGGREGATES FOR USE IN UNBOUND SUBBASE APPLICATION

2014 ◽  
Vol 20 (2) ◽  
pp. 169-174 ◽  
Author(s):  
Vahid Ayan ◽  
Mukesh C. Limbachiya ◽  
Joshua R. Omer ◽  
Seyyed Masoud Nasr Azadani
Keyword(s):  
Moisture Content ◽  
Asphalt Pavement ◽  
Optimum Moisture Content ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Dry Density ◽  
Reclaimed Asphalt Pavement ◽  
Maximum Dry Density ◽  
Reclaimed Asphalt ◽  
Natural Aggregates

Study was recently conducted at Kingston University to assess the suitability of using recycled concrete aggregate (RCA) and reclaimed asphalt pavement (RAP) in unbound subbase mixtures. The results showed that the use of 100% recycled aggregates increased the optimum moisture content and decreased the maximum dry density of the sub-base materials in comparison with natural aggregates. Moreover, the replacement of RCA by reclaimed asphalt pavement by 50% decreased the optimum moisture content and increased the maximum dry density in proportion to 100% RCA. The effects of physical properties on 0% air void and compaction curve were discussed for each type of subbase. The CBR values of the subbase materials prepared with 100%RCA is lower than subbase mixture with 100% natural aggregates. The CBR further decreased for replaced subbase with RAP so that 50%RCA + 50%RAP is not suitable for unbound subbase from the point of CBR view. In each mix the trend of CBR value was investigated in terms of water content. This research found some significant practical points to use in site works.

Sign in / Sign up

Export Citation Format

Share Document