A Study of Soil Stabilization by Hydrated Lime at Kampung Kedaik Asal, Rompin, Pahang, Malaysia

2014 ◽  
Vol 695 ◽  
pp. 738-741
Author(s):  
Azhani Zukri ◽  
Nadiatul Adilah Ahmad Abdul Ghani
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Optimum Moisture Content ◽  
Natural State ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Lime Content ◽  
Curing Period

This study involves the clay sample which is taken from Kampung Kedaik Asal, Rompin site and evaluation of its properties in natural state and after stabilization. The main objectives of this paper is to estimate the optimum lime content (OLC) needed to stabilize the soil by using Eades-Grim pH Test, to determine the optimum moisture content (OMC) and maximum dry density (MDD) of the treated soil by Standard Proctor Test and also the strength value of the soil specimens with different percentages of lime content corresponding with different curing period by Unconfined Compressive Strength (UCS) Test. From this study, the optimum amount to stabilize the clay soil and minimum amount of lime required to stabilize the soil pH level to 12 is 5%. The results showed that addition of lime decreased the maximum dry density (MDD) and increased the optimum moisture content (OMC). Unconfined compressive test on 48 sets of samples has been carried out for 7, 14 and 28 days of curing with different lime contents such as 5%, 7% and 9%. The highest unconfined compressive strength (UCS) achieved is 321 kN/m2 for clay stabilized with 9% lime content cured at 28 days. From the test results, it was found that the longer the immersion of curing period with higher lime content, the greater the compressive strength of the specimen.

scholarly journals Strength Improvement of Weak Subgrade Soil Using Cement and Lime

2019 ◽  
Vol 4 (1) ◽  
Author(s):  
Anigilaje B Salahudeen ◽  
Ja’afar A Sadeeq
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Optimum Moisture Content ◽  
Atterberg Limits ◽  
California Bearing Ratio ◽  
Natural Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Subgrade Soil

The study investigate the suitability of subgrade soil in Baure Local Government Area of Kastina State Nigeria for road construction. The strength properties of the  subgrade was improved using lime and cement. Several analysis including the particle size distribution, specific gravity, Atterberg limits, compaction characteristics, unconfined compressive strength and California bearing ratio tests were performed on natural and lime/cement treated soil samples in accordance with BS 1377 (1990) and BS 1924 (1990) respectively. Soil specimens were prepared by mixing the soil with lime and cement in steps of 0, 3, 6, and 9% by weight of dry soil in several percentage combinations. The Atterberg limits of the weak subgrade soils improved having a minimum plasticity index value of 5.70 % at 3%Lime/6%Cement contents. The maximum dry density (MDD) values obtained showed a significant improvement having a peak value of 1.66 kN/m3 at 9%Lime/9%Cement contents. Similarly, a minimum value of 18.50 % was observed for optimum moisture content at 9%Lime/9%Cement contents which is a desirable reduction from a value of 25.00 % for the natural soil. The unconfined compressive test value increased from 167.30 kN/m2 for the natural soil to 446.77 kN/m2 at 9%Lime/9%Cement contents 28 days curing period. Likewise, the soaked California bearing ratio values increased from 2.90 % for the natural soil to 83.90 % at 9%Lime/9%Cement contents. Generally, there were improvements in the engineering properties of the weak subgrade soil when treated with lime and cement. However, the peak UCS value of 446.77 kN/m2 fails to meet the recommended UCS value of 1710 KN/m2 specified by TRRL (1977) as a criterion for adequate stabilization using Ordinary Portland Cement.            Keywords: Weak subgrade soil, Lime, Cement, Atterberg limits, Maximum dry density, Optimum moisture content, Unconfined compressive strength, California bearing ratio

scholarly journals Engineering behaviour of stabilized laterite and kaolin using lignin

2018 ◽  
Vol 250 ◽  
pp. 01008
Author(s):  
Tuan Noor Hasanah Tuan Ismail ◽  
Siti Aimi Nadia Mohd Yusoff ◽  
Ismail Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
...  
Keyword(s):  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Laboratory Tests ◽  
Dry Weight ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Laterite Soil ◽  
Maximum Dry Density ◽  
Steady Rate

Soils at many sites do not always have enough strength to bear the structures constructed over them and some of the soil may need to be stabilized in order to improve their geotechnical properties. In this paper, routine laboratory tests were critically carried out to investigate the efficacy of lignin in improving the strength behaviour of the soils. Two different soil samples (laterite and kaolin) were studied and mixed with different proportions of lignin (2% and 5% of dry weight of soil), respectively. Unconfined Compressive Strength (UCS) characteristics evaluated in this study were done on samples at their maximum dry density and optimum moisture content (obtained from compaction tests). The UCS tests on all the specimens were carried out after 0, 7, 15, 21 and 30 days of controlled curing. The research results showed that the addition of lignin into kaolin reduced its maximum dry density while giving progressively higher optimum moisture content. Contrarily, with the laterite soil, both maximum dry density and optimum moisture content simultaneously increased when lignin was added into the soils. The UCS results showed that the the stabilized laterite with 2% lignin continued to gain strength significantly at a fairly steady rate after 7 days. Unfortunately, lignin did not show a significant effect in kaolin.

scholarly journals Using Nanomaterials in Stabilization of Soil for Oil Infrastructures

2020 ◽  
Vol 10 (3) ◽  
pp. 36-53
Author(s):  
Dr. Zaid Hameed Majeed ◽  
Eng. Kadhim Jawad Aubais ◽  
Dr. Mohd Raihan Taha
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Dry Weight ◽  
Environmental Benefits ◽  
Al2o3 Content ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Geotechnical Characteristics ◽  
Compressible Soil

The design foundations  of storage tanks for oil industry experiences significant problems due to the widespread occurrence of weak and compressible soil which resulted in foundation failure. In this study, soft soils were taken from two locations and mixed with three types of nanoparticles which were nano-alumina (nano Al2O3), nano-copper (nano CuO), and nano-magnesium (nano MgO). Nanomaterials were incorporated in small percentage (less than 1%) by dry weight of soil. The tested geotechnical characteristics included the water content, dry density, and the unconfined compressive strength. The results showed significant enhancements in the maximum dry density and unconfined compressive strength. The level of enhancement depended on the type of nanomaterials and the contents. Improved strength and hardening properties were shown with the utilization of nano CuO material in comparison to the soil samples with the other nanomaterials additions, with its optimum addition of 0.7% provided an increment rate of 662.7% while the optimum nano CuO which is about 1% showed a 532% increasing rate in the compressive strength of S1 soil. It was noted that the maximum dry density and unconfined compressive strength enhanced with the increase in the nanoparticles content until reaching a percentage in which the strength decreased. The optimum content of the nano MgO was 0.3% while the optimum nano Al2O3 content was about 0.3% for soil S1 and was about 0.1% for soil S2. The presence of nanomaterials in excessive contents caused agglomeration of particles which had negative influences on mechanical characteristics of the soils. Generally, the incorporation of finer particles like nanoparticles even with low amount would improve the geotechnical characteristics of soils with the consideration of the potential environmental benefits, these combined admixtures are intended to lower the cost and become a more sustainable and environmental alternative for soil stabilization

scholarly journals Influence of Waste Marble Dust on the Improvement of Expansive Clay Soils

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Hassan A. M. Abdelkader ◽  
Mohamed M. A. Hussein ◽  
Haiwang Ye
Keyword(s):  
Moisture Content ◽  
Soil Stabilization ◽  
Clayey Soil ◽  
Expansive Soil ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Expansive Clay ◽  
Maximum Dry Density ◽  
Marble Dust ◽  
Soil Mixtures

The marble process industry from Shaq Al-Thouban region, which is located in East Cairo, Egypt, produces a huge amount of marble wastes every day during the cutting and processing stages. Up to now, most of these wastes are dumping on open land which creates serious environmental problems. The amount of waste marble from the processing stage is about 20 to 25% of the total processed stone. Egypt also suffers from the problem of expansive soil that occupies a large area of its lands, especially in the new cities that are built on these lands. The primary purpose of this study is to use this waste material in the soil stabilization in point of view utilization of this waste as local low-cost materials and elimination of their negative environmental impacts. The waste marble dust was mixed with expansive soil samples with various percentages of 5%, 10%, 15%, 20%, and 25% by dry weight of soil. Different tests including Atterberg’s limits, standard Proctor compaction, unconfined compressive strength (UCS), California bearing ratio (CBR), swelling percentage, linear shrinkage (LS) tests, and XRF and XRD analyses were conducted for natural and marble dust stabilized soils. The soil mixtures used for UCS, CBR, and swell tests were compacted at the optimum moisture content (OMC) and maximum dry density (MDD) using the standard Proctor compaction method and cured for 7 days. The results of the tests showed that there are significant effects in enhancing the properties of expansive soils. Also, the results showed that as the percentage of the marble dust increases the plasticity index, the swelling potential of the expansive clayey soil decreases. Furthermore, the optimum moisture content decreases, and the maximum dry density increases. Also, UCS, CBR, and the calcite content of the soil mixtures increase with the increase in marble dust content.

scholarly journals A feasibility study on calcareous soil stabilization using polymers in Barka region.

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
S.V. Satyanarayana ◽  
Mohammed Al Jahwari
Keyword(s):  
Moisture Content ◽  
Bearing Capacity ◽  
Calcareous Soil ◽  
Soil Stabilization ◽  
Synthetic Polymer ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Atterberg Limit

In the Gulf region most of the soils require soil stabilization to increase soil bearing capacity for construction of safe and sustainable buildings. The soils are stabilized either by physical stabilization, chemical stabilization or by mechanical stabilization. The aim of this project is to stabilize calcareous soil in the Barka region with synthetic polymers. The soil samples from the Barka region collected by using standard soil sampling methods. The synthetic polymer was mixed with the calcareous soil in 1%, 3% and 5%. The soil samples were tested for sieve analysis, Atterberg Limit, Particle Density, Proctor test and California Bearing Ratio test before and after addition of synthetic polymer. It was observed that there is a positive impact on the geotechnical properties of soil with the addition of Polymer. The optimum moisture content of the soil reduced and the maximum dry density of the soil increased. The optimum results were found at 5% addition of polymer where the optimum moisture content was found out to be 12.6% and the maximum dry density was found out to be 1.997 Mg/m3. The Atterberg limit test to show that the plasticity index of the soil reduced with the addition of polymer and the optimum results were found out at 5% addition of polymer. Finally, the CBR test results determine that the soil bearing capacity increases with the addition of Polymer. After the addition of 5% Polymer, the CBR value was found out to be 27.465% compared to 14.19% for the fresh calcareous soil. The results are encouraging. Keywords: Atterberg Limit, Calcareous soil, CBR, polymer, stabilization.

scholarly journals Characterization and Comparison Research on Composite of Alluvial Clayey Soil Modified with Fine Aggregates of Construction Waste and Fly Ash

2021 ◽  
Vol 28 (1) ◽  
pp. 83-95
Author(s):  
Qu Jili ◽  
Wang Junfeng ◽  
Batugin Andrian ◽  
Zhu Hao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Clayey Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Construction Waste ◽  
Comparison Research ◽  
Fine Aggregates ◽  
Optimum Water Content

Abstract Fine aggregates of construction waste and fly ash were selected as additives to modify the characteristics of Shanghai clayey soil as a composite. The laboratory tests on consistency index, maximum dry density, and unconfined compressive strength were carried out mainly for the purpose of comparing the modifying effect on the composite from fine aggregates of construction waste with that from fly ash. It is mainly concluded from test results that the liquid and plastic limit of the composites increase with the content of two additives. But their maximum dry density all decreases with the additive content. However, fine aggregates of construction waste can increase the optimum water content of the composites, while fly ash on the contrary. Finally, although the two additive all can increase the unconfined compressive strength of composites, fly ash has better effect. The current conclusions are also compared with previous studies, which indicates that the current research results are not completely the same as those from other researchers.

scholarly journals Effect of Sand Percentage on the Compaction Properties and Undrained Shear Strength of Low Plasticity Clay

2021 ◽  
Vol 9 (1) ◽  
pp. 16-20
Author(s):  
Iyad Alkroosh ◽  
Ali Al-Robay ◽  
Prabir Sarker ◽  
Saif Alzabeebee
Keyword(s):  
Shear Strength ◽  
Moisture Content ◽  
Undrained Shear Strength ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Sand Content ◽  
Compression Tests ◽  
Maximum Dry Density ◽  
Sand Mixture ◽  
Undrained Shear

This paper investigates the influence of sand content on the mechanical behavior of a low plasticity clay that collected from south of Iraq (Sumer town). Samples have been prepared with sand contents of 0%, 10%, 20%, 30%, and 40% of the clay weight. Standard Proctor and unconfined compression tests have been carried out and the optimum moisture content, maximum dry density, and undrained shear strength have been determined. The results show a gradual increasing trend of the maximum dry density with the increase of the sand content up to 30%. The highest dry density reaches 1.90 g/cm3 corresponding to an optimum moisture content of 12%. In addition, this paper shows that the undrained shear strength is inversely proportional to the increase of the percentage of sand. The results of this work provide a useful addition to the literature regarding the behaviour or low plasticity clay-sand mixture.

Compaction Characteristic of Lime Modified Expansive Soil

2013 ◽  
Vol 710 ◽  
pp. 348-351
Author(s):  
Zheng Rong Zhao ◽  
Lei Wang ◽  
Hong Xia Yang
Keyword(s):  
Moisture Content ◽  
Expansive Soil ◽  
Size Composition ◽  
Optimum Moisture Content ◽  
Dry Density ◽  
Content Increase ◽  
Maximum Dry Density ◽  
Compaction Curve ◽  
Compaction Characteristic ◽  
Two Peaks

Through compaction test discussed about the compaction characteristics of expansive soil by lime modified in middle of Shandong province. The results show that the optimum moisture content is lower when the expansive soil is cured by dry compaction method, and the maximum dry density is higher. Compaction curve appeared the phenomenon of two peaks when expansive soil is cured by wet compaction method.Lime content of lime improved expansive soil, particle size composition, age and compaction function have influence on compaction curve.With the increase of the quantity of lime, the optimum moisture content increases, the maximum dry density decreases. With the age growth, the optimum moisture content increase slightly,the maximum dry density decreases slightly. The bigger the compaction work, the smaller moisture content is, the larger the maximum dry density is.

Shear Strength of BC-Soil Admixed with Lime and Bio-Enzyme

2019 ◽  
Vol 969 ◽  
pp. 327-334
Author(s):  
C. Jairaj ◽  
M.T. Prathap Kumar ◽  
H. Muralidhara
Keyword(s):  
Shear Strength ◽  
Soil Stabilization ◽  
Morphological Changes ◽  
Ground Improvement ◽  
High Strength ◽  
Sem Analysis ◽  
Dry Density ◽  
Test Results ◽  
Maximum Dry Density ◽  
Lime Content

This BC Soil are expansive in nature and are problematic because of low shear strength and high compressibility. Review of literatures have proven that addition of lime imparts high strength with a corresponding reduction in swell of BC soils. In addition, Bio-enzymes have also been found to play a key role as activators in improving the characteristics of clayey soils such as BC soil. Development and use of non-traditional ground improvement techniques such as bio-enzymes in combination with lime for soil stabilization helps to reduce the cost and the detrimental effects on the soil environment. In the present study lime and bio-enzymes were used as soil stabilizing agents. Compaction test results on BC soil admixed with different percent of lime indicated that 3% addition lime gives higher maximum dry density of 17kN/m3 with OMC of 21% compare to other addition of lime percentages. Keeping 3% of lime as optimum lime content(OLC), BC Soil was admixed with different dosages of Bio-enzymes 25ml/m3, 50ml/m3, 100 ml/m3,150ml/m3, and 200ml/m3 along with OLC was tested for compaction and unconfined compressive strength(UCC). Further UCC test was carried out for different curing period of 0, 7, 15, 30, and 60 Days to analyse the long term effect of BC soil admixed with bio-enzymes with and without lime content. Morphological and chemical analysis was done by using XRD and SEM analysis, from all the test results it was found that 3%OLC + 75ml/m3 of bio-enzymes for 7 day of curing gives higher UCC of 450 kPa. From the SEM it was found that better bond between particles found to develop in bio-enzyme+ lime admixed BC soil in comparison with lime alone admixed BC soil. XRD studies indicated morphological changes in crystallinity and structure of stabilized BC soil in comparison to BC soil alone.

scholarly journals Influence of Nanolime and Curing Period on Unconfined Compressive Strength of Soil

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Panbarasi Govindasamy ◽  
Mohd Raihan Taha ◽  
Jamal Alsharef ◽  
Kowstubaa Ramalingam
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Curing Time ◽  
Strength Gain ◽  
Treated Soil ◽  
Soil Particles ◽  
Curing Period

This paper presents the improvement of the unconfined compressive strength (UCS) of soil by mixing different percentages of nanolime and 5% lime with soil. The UCS of treated soil increased significantly over curing time with increasing percentage of nanolime. The optimum results were reached at only 0.5% nanolime admixtures which were much higher than 5% lime admixture. This may be due to higher ability of nanolime to flocculate and agglomerate the soil particles compared with the lime. In addition, the lime could fill only the micropores while nanolime could fill the micro- and nanopores as well. The strength gain is inversely proportional to the remolded moisture content and curing period. However, when the content of nanolime used is larger than 0.5%, nanolime particles are not uniformly dispersed. Therefore, a weak area in the form of voids is created, consequently the homogeneous hydrated microstructure cannot be formed, and finally the strength will decrease.

Sign in / Sign up

Export Citation Format

Share Document