Transition from Unsteady Flow Inception to Rotating Stall and Surge in a Transonic Compressor

2022 ◽  
Vol 31 (1) ◽  
pp. 120-129
Author(s):  
Dongming Cao ◽  
Caijia Yuan ◽  
Dingxi Wang ◽  
Xiuquan Huang
Keyword(s):  
Unsteady Flow ◽  
Rotating Stall ◽  
Transonic Compressor

scholarly journals Effects of Tip Leakage Flow on the Aerodynamic Performance and Stability of an Axial-Flow Transonic Compressor Stage

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4168
Author(s):  
Botao Zhang ◽  
Xiaochen Mao ◽  
Xiaoxiong Wu ◽  
Bo Liu
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Transonic Compressor

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.

The Behavior of the Casing Boundary Layer With the Presence of Tip Leakage Vortex

2018 ◽  
Author(s):  
Xi Nan ◽  
Feng Lin ◽  
Takehiro Himeno ◽  
Toshinori Watanabe
Keyword(s):  
Boundary Layer ◽  
Skin Friction ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Transonic Compressor ◽  
Flow Loss ◽  
Produce Flow

Casing boundary layer effectively places a limit on the pressure rise capability achievable by the compressor. The separation of the casing boundary layer not only produce flow loss but also closely related to the compressor rotating stall. The motivation of this paper is to present a viewpoint that the casing boundary layer should be paid attention to in parallel with other flow factors on rotating stall trigger. This paper illustrates the casing boundary layer behavior by displaying its separation phenomena with the presence of tip leakage vortex at different flow conditions. Skin friction lines and the corresponding absolute streamlines are used to demonstrate the three-dimensional flow patterns on and near the casing. The results depict a Saddle, a Node and several tufts of skin friction lines dividing the passage into four zones. The tip leakage vortex is enfolded within one of the zones by the separated flows. All the flows in each blade passage are confined within the passage as long as the compressor is stable. The casing boundary layer of a transonic compressor is also examined in the same way, which results in qualitatively similar zonal flows that enfolds the tip leakage vortex. This research develops a new way to study the casing boundary layer in rotating compressors. The results may provide a first-principle based explanation to stalling mechanisms for compressors that are casing sensitive.

Numerical Investigations on Partial Surge Initiated Inception and Stall Evolution in a Transonic Compressor

2017 ◽  
Author(s):  
Jiaguo Hu ◽  
Tianyu Pan ◽  
Wenqian Wu ◽  
Qiushi Li ◽  
Yifang Gong
Keyword(s):  
High Performance ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Rapid Decline ◽  
Second Phase ◽  
Stall Inception ◽  
Transonic Compressor ◽  
Transient Simulations ◽  
Two Factors

The instability has been the largest barrier of the high performance axial compressor in the past decades. Stall inception, which determines the route and the characteristics of instability evolution, has been extensively focused on. A new stall inception, “partial surge”, is discovered in the recent experiments. In this paper full-annulus transient simulations are performed to study the origin of partial surge initiated inception and explain the aerodynamic mechanism. The simulations show that the stall inception firstly occurs at the stator hub region, and then transfers to the rotor tip region. The compressor finally stalled by the tip region rotating stall. The stall evolution is in accord with the experiments. The stall evolution can be divided into three phases. In the first phase, the stator corner separation gradually merged with the adjacent passages, producing an annulus stall cell at the stator hub region. In the second phase, the total pressure rise of hub region emerges rapid decline due to the fast expansion of the annulus stall cell, but the tip region maintains its pressure rise. In the third phase, a new rotating stall cell appears at the rotor tip region, leading to the onset of fast drop of the tip region pressure rise. The stall cells transfer from hub region to the tip region is caused by two factors, the blockage of the hub region which transfers more load to the tip region, and the separation fluid fluctuations in stator domain which increase the circumferential non-uniformity in the rotor domain. High load and non-uniformity at the rotor tip region induce the final rotating stall.

The Present Challenge of Transonic Compressor Blade Design

2018 ◽  
Author(s):  
A. Hergt ◽  
J. Klinner ◽  
J. Wellner ◽  
C. Willert ◽  
S. Grund ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Shock Waves ◽  
Unsteady Flow ◽  
Flow Behavior ◽  
Flow Behaviour ◽  
Compressor Cascade ◽  
Transonic Compressor ◽  
Flow Phenomena ◽  
Transonic Cascade

The flow through a transonic compressor cascade shows a very complex structure due to the occuring shock waves. In addition, the interaction of these shock waves with the blade boundary layer inherently leads to a very unsteady flow behaviour. The aim of the current investigation is to quantify this behaviour and its influence on the cascade performance as well as to describe the occuring transonic flow phenomena in detail. Therefore, an extensive experimental investigation of the flow in a transonic compressor cascade has been conducted within the transonic cascade wind tunnel of DLR at Cologne. In this process, the flow phenomena were thoroughly examined for an inflow Mach number of 1.21. The experiments investigate both, the laminar as well as the turbulent shock wave boundary layer interaction within the blade passage and the resulting unsteady behaviour. The experiments show a fluctuation range of the passage shock wave of about 10 percent chord for both cases, which is directly linked with a change of the inflow angle and of the operating point of the cascade. Thereafter, RANS simulations have been performed aiming at the verification of the reproducibility of the experimentally examined flow behavior. Here it is observed that the dominant flow effects are not reproduced by a steady numerical simulation. Therefore, a further unsteady simulation has been carried out in order to capture the unsteady flow behaviour. The results from this simulation show that the fluctuation of the passage shock wave can be reproduced but not in the correct magnitude. This leads to a remaining weak point within the design process of transonic compressor blades, because the working range will be overpredicted. The resulting conclusion of the study is that the use of scale resolving methods such as LES or the application of DNS is necessary to correctly predict unsteadiness of the transonic cascade flow and its impact on the cascade performance.

Reduced-Order Modelling of Rotating Stall

2020 ◽  
Author(s):  
Dominik Schlüter ◽  
Robert P. Grewe ◽  
Fabian Wartzek ◽  
Alexander Liefke ◽  
Jan Werner ◽  
...  
Keyword(s):  
Single Cell ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Stability Limit ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Transonic Compressor ◽  
Experimental Findings

Abstract Rotating stall is a non-axisymmetric disturbance in axial compressors arising at operating conditions beyond the stability limit of a stage. Although well-known, its driving mechanisms determining the number of stall cells and their rotational speed are still marginally understood. Numerical studies applying full-wheel 3D unsteady RANS calculations require weeks per operating point. This paper quantifies the capability of a more feasible quasi-2D approach to reproduce 3D rotating stall and related sensitivities. The first part of the paper deals with the validation of a numerical baseline the simplified model is compared to in detail. Therefore, 3D computations of a state-of-the-art transonic compressor are conducted. At steady conditions the single-passage RANS CFD matches the experimental results within an error of 1% in total pressure ratio and mass flow rate. At stalled conditions, the full-wheel URANS computation shows the same spiketype disturbance as the experiment. However, the CFD underpredicts the stalling point by approximately 7% in mass flow rate. In deep stall, the computational model correctly forecasts a single-cell rotating stall. The stall cell differs by approximately 21% in rotational speed and 18% in circumferential size from the experimental findings. As the 3D model reflects the compressor behaviour sufficiently accurate, it is considered valid for physical investigations. In the second part of the paper, the validated baseline is reduced in radial direction to a quasi-2D domain only resembling the compressor tip area. Four model variations regarding span-wise location and extent are numerically investigated. As the most promising model matches the 3D flow conditions in the rotor tip region, it correctly yields a single-cell rotating stall. The cell differs by only 7% in circumferential size from the 3D results. Due to the impeded radial migration in the quasi-2D slice, however, the cell exhibits an increased axial extent. It is assumed, that the axial expansion into the adjacent rows causes the difference in cell speed by approximately 24%. Further validation of the reduced model against experimental findings reveals, that it correctly reflects the sensitivity of circumferential cell size to flow coefficient and individual cell speed to compressor shaft speed. As the approach reduced the wall clock time by 92%, it can be used to increase the physical understanding of rotating stall at much lower costs.

Unsteady Aerodynamics of Low-Pressure Steam Turbines Operating Under Low Volume Flow

2013 ◽  
Author(s):  
Benjamin Megerle ◽  
Timothy Stephen Rice ◽  
Ivan McBean ◽  
Peter Ott
Keyword(s):  
Unsteady Flow ◽  
Steam Turbine ◽  
Measurement Data ◽  
Unsteady Aerodynamics ◽  
Low Pressure ◽  
Rotating Stall ◽  
Stage Model ◽  
Steam Turbines ◽  
Multi Stage ◽  
Low Volume

Non-synchronous excitation under low volume operation is a major risk to the mechanical integrity of last stage moving blades (LSMBs) in low-pressure (LP) steam turbines. These vibrations are often induced by a rotating aerodynamic instability similar to rotating stall in compressors. Currently extensive validation of new blade designs is required to clarify whether they are subjected to the risk of not admissible blade vibration. Such tests are usually performed at the end of a blade development project. If resonance occurs a costly redesign is required, which may also lead to a reduction of performance. It is therefore of great interest to be able to predict correctly the unsteady flow phenomena and their effects. Detailed unsteady pressure measurements have been performed in a single stage model steam turbine operated with air under ventilation conditions. 3D CFD has been applied to simulate the unsteady flow in the air model turbine. It has been shown that the simulation reproduces well the characteristics of the phenomena observed in the tests. This methodology has been transferred to more realistic steam turbine multi stage environment. The numerical results have been validated with measurement data from a multi stage model LP steam turbine operated with steam. Measurement and numerical simulation show agreement with respect to the global flow field, the number of stall cells and the intensity of the rotating excitation mechanism. Furthermore, the air model turbine and model steam turbine numerical and measurement results are compared. It is demonstrated that the air model turbine is a suitable vehicle to investigate the unsteady effects found in a steam turbine.

Rotating Instability in an Annular Cascade: Detailed Analysis of the Instationary Flow Phenomena

2013 ◽  
Vol 136 (6) ◽  
Author(s):  
Benjamin Pardowitz ◽  
Ulf Tapken ◽  
Robert Sorge ◽  
Paul Uwe Thamsen ◽  
Lars Enghardt
Keyword(s):  
Unsteady Flow ◽  
High Speed ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Tip Vortex ◽  
Pressure Waves ◽  
Flow Profile ◽  
Rotating Instability ◽  
Annular Cascade

Rotating instability (RI) occurs at off-design conditions in compressors, predominantly in configurations with large tip or hub clearance ratios of s* ≥3%. RI is the source of the blade tip vortex noise and a potential indicator for critical operating conditions like rotating stall and surge. The objective of this paper is to give more physical insight into the RI phenomenon using the analysis results of combined near-field measurements with high-speed particle image velocimetry (PIV) and unsteady pressure sensors. The investigation was pursued on an annular cascade with hub clearance. Both the unsteady flow field next to the leading edge as well as the associated rotating pressure waves were captured. A special analysis method illustrates the characteristic pressure wave amplitude distribution, denoted as “modal events” of the RI. Moreover, the slightly adapted method reveals the unsteady flow structures corresponding to the RI. Correlations between the flow profile, the dominant vortex structures, and the rotating pressure waves were found. Results provide evidence to a new hypothesis, implying that shear layer instabilities constitute the basic mechanism of the RI.

Experimental investigations on instability evolution in a transonic compressor at different rotor speeds

2015 ◽  
Vol 229 (18) ◽  
pp. 3378-3391 ◽  
Author(s):  
Qiushi Li ◽  
Tianyu Pan ◽  
Tailu Sun ◽  
Zhiping Li ◽  
Yifang Gong
Keyword(s):  
Low Frequency ◽  
Axial Flow ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Rotor Speed ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
New Type ◽  
Flow Compressor

Experimental investigations are conducted to study the instability evolution in a transonic axial flow compressor at four specific rotor speeds covering both subsonic and transonic operating conditions. Two routes of evolution to final instability are observed in the test compressor: at low rotor speeds, a disturbance in the rotor tip region occurs and then leads to rotating stall, while at high rotor speeds, a low-frequency disturbance in the hub region leads the compressor into instability. Different from stall and surge, this new type of compressor instability at high rotor speed is initiated through the development of a low-frequency axisymmetric disturbance at the hub, and we name it “partial surge”. The frequency of this low-frequency disturbance is approximately the Helmholtz frequency of the system and remains constant during instability inception. Finally, a possible mechanism for the occurrence of different instability evolutions and the formation of partial surge are also discussed.

Unsteady Flow and Aeroelasticity Behaviour of Aero-Engine Core Compressors During Rotating Stall and Surge

2006 ◽  
Author(s):  
M. Vahdati ◽  
G. Simpson ◽  
M. Imregun
Keyword(s):  
Experimental Data ◽  
Unsteady Flow ◽  
Mass Flow ◽  
Rotor Blade ◽  
Rotating Stall ◽  
Flow Reversal ◽  
The Core ◽  
Single Passage ◽  
Aero Engine ◽  
Operating Points

The paper will focus on two core-compressor instabilities, namely rotating stall and surge. Using a 3D viscous time-accurate flow representation, the front bladerows of a core-compressor were modelled in a whole-annulus fashion whereas the rest of bladerows were represented in single passage fashion. The rotating stall behaviour at two different compressor operating points was studied by considering two different variable-vane scheduling conditions for which experimental data were available. Using a model with 9 whole bladerows, the unsteady flow calculations were conducted on 32-CPUs of a parallel cluster, typical run times being around 3–4 weeks for a grid with about 60 million points. The simulations were conducted over several engine rotations. As observed on the actual development engine, there was no rotating stall for the first scheduling condition while mal-scheduling of the stator vanes created a 12 band rotating stall which excited the rotor blade 1st flap mode. In a separate set of calculations, the surge behaviour was modelled using a time-accurate single-passage representation of the core compressor. It was possible to predict not only flow reversal into the low pressure compression domain, but also the expected hysteresis pattern of the surge loop in terms of its mass flow vs pressure characteristic.

Sign in / Sign up

Export Citation Format

Share Document