Impact modification of hybrid polypropylene composites with poly(vinyl alcohol) fibers

Polypropylene (PP) hybrid composites were prepared by the combination of three reinforcing (carbon, glass, and wood) and a synthetic (PVA) fiber. Tensile and impact testing, acoustic emission measurements, and scanning electron microscopy (SEM) were used for the characterization of the composites as well as to follow deformation and failure processes. The results obtained prove that the novel concept of using synthetic fibers for impact modification can be applied successfully also with PVA fibers. The extent of improvement in impact strength depends on fiber type and content, but also on interfacial adhesion which strongly influences the local deformation processes occurring around the fibers during fracture. Both the reinforcing and the synthetic fibers take part in these processes and contribute to energy consumption. Debonding and the subsequent plastic deformation of the matrix consumes energy the most efficiently, but the fracture of the PVA fibers also requires energy; thus, PVA fibers improve impact resistance both at poor and good adhesion. This approach allows the design of materials for structural applications; the combination of a stiffness of 4–6 GPa and an impact resistance of 20–25 kJ/m2 exceeds the properties of most PP composites available on the market.

Morphometric Study of Craters on Saturn’s Moon Rhea

Morphometric studies of impact craters on icy moons can be used to understand modification of crater topography. Several processes (e.g., viscous relaxation, ejecta deposition, repeated and overlapping impacts) act to shallow crater depth and relax the crater wall slope to similar or varying extents. Resolving these processes can help constrain the interior structure and surface properties of icy moons. Here, using morphometric measurements of craters on Rhea, we aim to constrain the processes that led to the observed crater population. We measured crater diameter, depth, and wall slope, as well as overall crater morphology (e.g., simple versus complex craters). Our results indicate that there exists a linear correlation between impact crater depth-to-diameter ratio and crater wall slope. This may suggest that the dominant modification process on Rhea is one that affects both properties simultaneously, which supports past heating events as the primary post-impact modification process. Additionally, the simple-to-complex crater transition for Rhea was found to be 12 ± 2 km, which is consistent with reported transition diameters for comparably sized icy bodies, indicating similar surface properties. A transition to shallower crater depths for large complex craters was not documented, indicating the absence of a rheological transition at depth in Rhea’s icy lithosphere, which may support the interpretation that Rhea is not fully differentiated.

Phase morphology, mechanical, and thermal properties of fiber-reinforced thermoplastic elastomer: Effects of blend composition and compatibilization

In this work, recycled high density polyethylene (rHDPE) was compounded with regenerated tire rubber (RR) (35–80 wt.%) and reinforced with recycled tire textile fiber (RTF) (20 wt.%) as a first step. The materials were compounded by melt extrusion, injection molded, and characterized in terms of morphological, mechanical, physical, and thermal properties. Although, replacement of the rubber phase with RTF compensated for tensile/flexural moduli losses of rHDPE/RR/RTF blends because of the more rigid nature of fibers increasing the composites stiffness, the impact strength substantially decreased. So, a new approach is proposed for impact modification by adding a blend of maleic anhydride grafted polyethylene (MAPE)/RR (70/30) into a fiber-reinforced rubberized composite. As in this case, a more homogeneous distribution of the fillers was observed due to better compatibility between MAPE, rHDPE, and RR. The tensile properties were improved as the elongation at break increased up to 173% because of better interfacial adhesion. Impact modification of the resulting thermoplastic elastomer (TPE) composites based on rHDPE/(RR/MAPE)/RTF was successfully performed (improved toughness by 60%) via encapsulation of the rubber phase by MAPE forming a thick/soft interphase decreasing interfacial stress concentration slowing down fracture. Finally, the thermal stability of rubberized fiber-reinforced TPE also revealed the positive effect of MAPE addition on molecular entanglements and strong bonding yielding lower weight loss, while the microstructure and crystallinity degree did not significantly change up to 60 wt.% RR/MAPE (70/30).