Dielectric and gas sensing properties of in situ electrochemically polymerized PPy-MgO-WO3 nanocomposite films

A polypyrrole-based ammonia-detection gas sensor was studied in this work. Under a 1.6 V electrodeposition potential, polypyrrole (PPy) was electrochemically synthesized from an aqueous solution of 0.1 M pyrrole and 0.1 M oxalic acid. An extension to the polypyrrole films was applied through electrochemical deposition on indium tin oxide (ITO), using the metal oxide nanoparticles of MgO and WO3. These films were investigated for their sensing behavior towards NH3 at different working temperatures and different weight percentages of nanoparticles .The measurements of A.C conductivity were conducted over a frequency range of 101-105 Hz and temperature range of 298-423 K . The highest electrical conductivity was equal to 3.67x10-1 Ω.cm-1 at a temperature of 323 K and frequency of 105H z. The experimental results showed that the sensitivity of the undoped and doped PPy with nanoparticle films to ammonia gas changes with the change in temperature and weight percentage.

Characteristics and corrosion protection of polypyrrole doped with salicylate anions on CT3 steel passivated by molydate

In recent years, the conducting polymers have attracted much attention in research and development because of their applications in medical and civil engineering. Here, the salicylate doped polypyrrole films were prepared on the carbon steel surface and their corrosion protection in 3 % NaCl solution were studied. Polypyrrole (Ppy) film was electrochemically synthesised with constant current techniques in a sodium salicylate solution (0.05M, 0.1M, 0.15M) and 0.1M pyrrole monomer on mild CT3 steel electrode passivated by molybdate. The morphological, structural, composition and thermal properties of salicylate doped Ppy films were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA) techniques. The anti-corrosion ability of these films was assessed by electrochemical measurements in 3 % NaCl solution. The obtained results suggested that salicylate anions contributed in corrosion protection ability of Ppy films for mild steel electrode. The concentration of sodium salicylate of 0.1M and pyrrole of 0.1M is most suitable for preparation of good protection coating. The self-healing mechanism has been also mentioned for salicylate doped Ppy films on CT3 steel substrate.

Photoelectrochemical Stability under Anodic and Cathodic Conditions of Meso-Tetra-(4-Sulfonatophenyl)-Porphyrinato Cobalt (II) Immobilized in Polypyrrole Thin Films

Cobalt porphyrins have emerged as promising catalysts for electrochemical and photoelectrochemical applications because of their good performance, low cost and the abundance of cobalt in the earth. Herein, a negatively charged porphyrin meso-tetra-(4-sulfonatophenyl)-porphin (TPPS) was immobilized in polypyrrole (PPy) during the electro-polymerization, and then it was metallized with cobalt to obtain meso-tetra-(4-sulfonatophenyl)-porphyrinato cobalt (II) (CoTPPS) as a dopant in PPy. The coatings were evaluated as photoelectrodes towards thiosulfate oxidation and oxygen reduction. For comparison purposes, the photoelectrochemical behavior of ClO4−-doped polypyrrole films was also evaluated. Characterizations by chronoamperometry, UV-Vis spectroscopy and Raman spectroscopy showed that polypyrrole is stable under anodic and cathodic conditions, but CoTPPS and TPPS immobilized in PPy are degraded during the anodic process. Thus, decreases in photocurrent of up to 87% and 97% for CoTPPS-doped PPy and TPPS-doped PPy were observed after a 30-min chronoamperometry test. On the other hand, good stability of CoTPPS and TPPS immobilized in PPy was observed during photoelectrochemical oxygen reduction, which was reflected in almost constant photocurrents obtained by chronoamperometry. These findings are relevant to understanding the role of CoTPPS as a catalyst or pre-catalyst in photoelectrochemical applications such as water splitting. In addition, these results could pave the way for further research to include CoTPPS-doped PPy in the design of novel photocathodes.

All-Dry, One-step Synthesis, Doping and Film Formation of Conductive Polypyrrole

Oxidative chemical vapor deposition (oCVD) is an extremely effective method for solvent-free deposition of highly conductive polypyrrole films, where polymer synthesis, doping, and film formation are combined in a single...

Experimental Study and Mathematical Modeling of a Glyphosate Impedimetric Microsensor Based on Molecularly Imprinted Chitosan Film

A novel impedimetric microsensor based on a double-layered imprinted polymer film has been constructed for the sensitive detection of the herbicide, glyphosate (GLY), in water. It is based on electropolymerized polypyrrole films, doped with cobaltabis(dicarbollide) ions ([3,3′-Co(1,2-C2B9H11)2]), as a solid contact layer between the gold microelectrode surface and the molecularly imprinted chitosan film (CS-MIPs/PPy/Au). Electrochemical Impedance Spectroscopy (EIS) was used for the characterization of the CS-molecular imprinted polymers (MIPs)/PPy/Au in the presence of GLY concentrations between 0.31 pg/mL and 50 ng/mL. Experimental responses of CS-MIPs/PPy/Au are modeled for the first time using an exact mathematical model based on physical theories. From the developed model, it was possible to define the optimal range of the parameters that will impact the quality of impedance spectra and then the analytical performance of the obtained microsensor. The obtained microsensor shows a low detection limit of 1 fg/mL (S/N = 3), a good selectivity, a good reproducibility, and it is regenerable.