Narrow-Linewidth GaN-on-Si Laser Diode with Slot Gratings

This letter reports room-temperature electrically pumped narrow-linewidth GaN-on-Si laser diodes. Unlike conventional distributed Bragg feedback laser diodes with hundreds of gratings, we employed only a few precisely defined slot gratings to narrow the linewidth and mitigate the negative effects of grating fabrication on the device performance. The slot gratings were incorporated into the ridge of conventional Fabry-Pérot cavity laser diodes. A subsequent wet etching in a tetramethyl ammonium hydroxide solution not only effectively removed the damages induced by the dry etching, but also converted the rough and tilted slot sidewalls into smooth and vertical ones. As a result, the threshold current was reduced by over 20%, and the reverse leakage current was decreased by over three orders of magnitude. Therefore, the room-temperature electrically pumped narrow-linewidth GaN-on-Si laser diode has been successfully demonstrated.

The Heating Efficiency and Imaging Performance of Magnesium Iron Oxide@tetramethyl Ammonium Hydroxide Nanoparticles for Biomedical Applications

Multifunctional magnetic nanomaterials displaying high specific loss power (SLP) and high imaging sensitivity with good spatial resolution are highly desired in image-guided cancer therapy. Currently, commercial nanoparticles do not sufficiently provide such multifunctionality. For example, Resovist® has good image resolution but with a low SLP, whereas BNF® has a high SLP value with very low image resolution. In this study, hydrophilic magnesium iron oxide@tetramethyl ammonium hydroxide nanoparticles were prepared in two steps. First, hydrophobic magnesium iron oxide nanoparticles were fabricated using a thermal decomposition technique, followed by coating with tetramethyl ammonium hydroxide. The synthesized nanoparticles were characterized using XRD, DLS, TEM, zeta potential, UV-Vis spectroscopy, and VSM. The hyperthermia and imaging properties of the prepared nanoparticles were investigated and compared to the commercial nanoparticles. One-dimensional magnetic particle imaging indicated the good imaging resolution of our nanoparticles. Under the application of a magnetic field of frequency 614.4 kHz and strength 9.5 kA/m, nanoparticles generated heat with an SLP of 216.18 W/g, which is much higher than that of BNF (14 W/g). Thus, the prepared nanoparticles show promise as a novel dual-functional magnetic nanomaterial, enabling both high performance for hyperthermia and imaging functionality for diagnostic and therapeutic processes.

On the Many Applications of Nanometer-Thin Pure Boron Layers in IC and Microelectromechanical Systems Technology

An overview is given of the many applications that nm-thin pure boron (PureB) layers can have when deposited on semiconductors such as Si, Ge, and GaN. The application that has been researched in most detail is the fabrication of nm-shallow p+n-like Si diode junctions that are both electrically and chemically very robust. They are presently used commercially in photodiode detectors for extremeultraviolet (EUV) lithography and scanning-electron-microscopy (SEM) systems. By using chemicalvapor deposition (CVD) or molecular beam epitaxy (MBE) to deposit the B, PureB diodes have been fabricated at temperatures from an optimal 700 °C to as low as 50 °C, making them both front- and back-end-of-line CMOS compatible. On Ge, near-ideal p+n-like diodes were fabricated by covering a wetting layer of Ga with a PureB capping layer (PureGaB). For GaN high electron mobility transistors (HEMTs), an Al-on-PureB gate stack was developed that promises to be a robust alternative to the conventional Ni-Au gates. In MEMS processing, PureB is a resilient nm-thin masking layer for Si micromachining with tetramethyl ammonium hydroxide (TMAH) or potassium hydroxide (KOH), and low-stress PureB membranes have also been demonstrated.

Investigation of 1/f and Lorentzian Noise in TMAH-treated Normally-Off GaN MISFETs

A tetramethyl ammonium hydroxide (TMAH)-treated normally-off Gallum nitride (GaN) metal-insulator-semiconductor field-effect transistor (MISFET) was fabricated and characterized using low-frequency noise (LFN) measurements in order to find the conduction mechanism and analyze the trapping behavior into the gate insulator as well as the GaN buffer layer. At the on-state, the noise spectra in the fabricated GaN device were 1/fγ properties with γ ≈ 1, which is explained by correlated mobility fluctuations (CMF). On the other hand, the device exhibited Lorentzian or generation-recombination (g-r) noises at the off-state due to deep-level trapping/de-trapping into the GaN buffer layer. The trap time constants (τi) calculated from the g-r noises became longer when the drain voltage increased up to 5 V, which was attributed to deep-level traps rather than shallow traps. The severe drain lag was also investigated from pulsed I-V measurement, which is supported by the noise behavior observed at the off-state.

Development of Novel Method for Immobilizing TMAH-Degrading Microbe into Pellet and Characterization Tool, for Verifying Its Robustness in Electronics Wastewater Treatment

This study describes an immobilization method of enriched microorganism, for robustly degrading organic compounds, including tetramethyl ammonium hydroxide (TMAH) in electronics wastewater without an increase of total organic carbon (TOC) in effluent. The enriched TMAH degrading bacteria was entrapped inside the pellets through polymerization. Polymerization conditions were optimized in terms of long-term TOC leak tests of pellet. Among several methods, a differential scanning calorimetry (DSC) analysis was found to be effective for the hands-on evaluation of stability in pellet. Stable pellets showed less than 10 J/g of curing heat by DSC analysis. This method is suitable for the optimization of polymerization conditions and controlling the quality of pellets. The removal efficiency of TMAH was over 95% and effluent concentration of TOC was below 100 ppb. The viability test results revealed that entrapped microorganisms were actively survived after five months of operations. This immobilization method is strongly suggested as a new strategy for the wastewater reuse process in low-strength electronics wastewater.

Improved removal of methylene blue on modified hierarchical zeolite Y: Achieved by a “destructive-constructive” method

In this study removal of methylene blue (MB) from an aqueous solution by zeolite (NaY) and related modified hierarchical zeolite (MY) has been investigated. The NaY zeolite with a low ratio of Si/Al was synthesized from silica extracted rice husk ash. It was transformed to hierarchical zeolite (MY) by a “destructive-constructive” modification method using tetramethyl ammonium hydroxide (TMAOH) and a cationic surfactant (Cetyltrime-thylammonium bromide, CTAB) as a templating agent. Various characterization method like FT-IR, XRF, XRD, BET, TGA, SEM and BJH confirmed the construction of parent zeolite and also successfulness of the modification process. EDX showed a negligible change of Si/Al ratio during modification which is favorite in adsorption of cationic MB dye. In order to study the interaction between the surface of adsorbent and adsorbate, six common isotherms were used. By Langmuir isotherm, it is clarified that, the maximum adsorption capacity (qm) had improvement from 15.2 mg g-1 to 133.1 mg g-1 for NaY and MY, respectively. The kinetic studies showed that the adsorption obeys the Pseudo-second order model for both NaY and MY zeolites. Also, the usage frequency of the MY was investigated. Results showed that there was not any noticeable change in performance of adsorption after four circles.

Inductively Coupled Plasma-Mass Spectrometric Determination of Iodine in Food Using Tetramethyl Ammonium Hydroxide Extraction—Results from a U.S. Food and Drug Administration Level 3 Interlaboratory Study

Background: The performance of U.S. Food and Drug Administration (FDA) Elemental Analysis Manual (EAM) 4.13 method (Inductively Coupled Plasma-Mass Spectrometric Determination of Iodine in Food Using Tetramethyl Ammonium Hydroxide Extraction) was tested in an interlaboratory study. Objective: The aim of the study is to demonstrate that the FDA EAM method 4.13 is applicable for the analysis of food and multivitamins. Methods: Six collaborators participated in the study using four different models of inductively coupled plasma-mass spectrometry instruments. The method evaluation included determination of the limits of detection and quantification, analysis of National Institute of Standards and Technology standard reference materials (SRMs), unknown samples, blinded SRMs, and fortified analytical portions by all six collaborators. The samples were chosen to represent all sectors of the AOAC food triangle and additionally included pet food and multivitamin tablets. Results: The repeatability and reproducibility ranges were 1.8–11.4% and 3.6–13.7%, respectively; the calculated HorRat values were in the 0.17–1.18 range; and 174 of 175 SRM analyses had z-scores <2 and fortified analytical portion samples with recoveries of 102–105%, indicating acceptable method performance. Conclusions: The study supports a Level Three Multilaboratory Validation according to FDA Food and Veterinary Program Guidelines performed by six collaborators using six certified reference materials and nine unknown samples. Highlights: The method is applicable for quantification of the total extractable iodine in food and multivitamin dietary supplements.