An Embedded Half-Bridge Γ-Z-Source Inverter with Reduced Voltage Stress on Capacitors

In this paper, an embedded half-bridge Z-source inverter based on gamma structure is proposed. In contrast with the classical half-bridge inverter, the proposed inverter can generate zero voltage levels in output. High voltage gain and low voltage stress on capacitors are the main advantages of the proposed converter. The value of the boost factor in the proposed structure is increased by changing both the shoot-through (ST) duty cycle and turns ratio of the transformer. The operating principle of the proposed converter in four operating modes is presented. We also calculate the critical inductance and compare the proposed converter with conventional topologies. In addition, power loss and THD analysis are presented. Finally, PSCAD/EMTDC software is used to verify the correct operation of the proposed inverter and the experimental results.

A New Two Switched-Impedance Network for High Ratio Quasi-Z-Source Inverter

The increasing demand and widespread of renewable energy inherently compel the development of power electronics converter as an interface between consumers and the energy source/s. This paper presents a new two switched-impedance networks qZSI converter called High Ratio Two Switched-impedance quasi-Z-Source Inverter (HR2SZ-qZSI). Compared with the previous topology, this proposed HR2SZ-qZSI topology can achieve higher voltage gain with lower shoot-through duty ratio, and a higher boost factor. This paper also discusses comparative analysis between the previous topology and the proposed HR2SZ-qZSI topology. Furthermore, the simulation and experimental data are presented to prove the theoretical analysis of the proposed HR2SZ-qZSI topology. Despite the additional components needed, it accentuates that this proposed converter retains all features of qZSI: common ground point between the dc source and converter and smooth input current operation. Furthermore, almost all the devices rating including capacitor and diode voltage, and inductor current ripple are lower than the preceding relevant two switched-impedance qZSI family. Accordingly, this proposed HR2SZ-qZSI clearly a good power conditioning alternative for renewable generation system.

The Three-Carrier Quasi Switched Boost Inverter Control Technique

This paper presents a carrier modulation technique to control the three-phase, two-level quasi switched boost inverter. This PWM algorithm uses three carrier waves, the first of which is for the inverter while the others are for the booster. The boost factor depends on the short circuit interval on the DC/DC booster and the inverter. When the short circuit interval on the DC boost is twice that on the inverter, the modulation index can be enlarged. The new algorithm is analyzed, calculated, simulated, and tested. The analysis and calculation results show that the proposed technique can reduce the voltage on the DC link capacitor compared to a conventional approach. It can reach 22.16% when the ratio of the DC source voltage to the effective reference voltage is 0.5. The modulation index can extend to 29% under these conditions and the current ripple in the boost inductor can be reduced by 4.8%. The simulation and experimental results also show similarities, thereby confirming the analysis and calculation.

Enhanced Boost Factor for Three-Level Quasi-Switched Boost T-Type Inverter

A new modulation strategy has been introduced in this paper in order to enhance the boost factor for the three-level quasi-switched boost T-type inverter (3L-qSBT2I). Under this approach, the component rating of power devices is significantly decreased. Moreover, the use of a larger boost factor produces a smaller shoot-through current. This benefit leads to reducing the conduction loss significantly. Furthermore, the neutral voltage unbalance is also considered. The duty cycle of two active switches of a quasi-switched boost (qSB) network is redetermined based on actual capacitor voltages to recovery balance condition. Noted that the boost factor will not be affected by the proposed capacitor voltage balance strategy. The proposed method is taken into account to be compared with other previous studies. The operation principle and overall control strategy for this configuration are also detailed. The simulation and experiment are implemented with the help of PSIM software and laboratory prototype to demonstrate the accuracy of this strategy.

Algorithim to control output voltage and reduce the ripple of input current in quasi switched boost inverter

In recent years, the quasi -switched boost inverter uses widely in electrical systems. This paper proposes a method to control the AC output voltage and reduce the current ripple of the booster inductor in the quasi-switched boost inverter (QSBI). The proposed technique base on carrier pulse width modulation with two triangles with phase shifts 90◦. This technique uses the offset function to expand the modulation index and the algorithm for output voltage stabilization based on the adjustment of the boost ratio. The modulation index expansion will reduce the stress voltage on the switches by an average of 16.5% under the simulated conditions. The boost factor base on the short circuit time on the DC / DC booster and the inverter on the zero vectors. So, the duty ratio (of the boost DC / DC) can reduce by the short-circuit pulses that insert in the position of zero vectors, so the inverter is responsible for both boosting and inverting. The combination helps to reduce the current ripple on the boost inductor. Besides that, reducing the short-circuit ratio of DC / DC booster will also reduce the capacity of the booster switch and thereby reduce the production cost. The analysis clarifies the proposed technique. Simulations and experiments evaluate the proposed method.

A High Step-Up Switched Z-Source Converter (HS-SZC) with Minimal Components Count for Enhancing Voltage Gain

Some applications such as fuel cells or photovoltaic panels offer low output voltage, and it is essential to boost this voltage before connecting to the grid through an inverter. The Z-network converter can be used for the DC-DC conversion to enhance the output voltage of renewable energy sources. However, boosting capabilities of traditional Z-network boost converters are limited, and the utilization of higher parts count makes it bulky and expensive. In this paper, an efficient, high step-up, switched Z-source DC-DC boost converter (HS-SZC) is presented, which offers a higher boost factor at a smaller duty ratio and avoids the instability due to the saturation of inductors. In the proposed converter, the higher voltage gain is achieved by using one inductor and switch at the back end of the conventional Z-source DC-DC converter (ZSC). The idea is to utilize the output capacitor for filtering and charging and discharging loops. Moreover, the proposed converter offers a wider range of load capacity, thus minimizing the power losses and enhancing efficiency. This study simplifies the structure of conventional Z-source converters through the deployment of fewer components, and hence making it more cost-effective and highly efficient, compared to other DC-DC boost converters. Furthermore, a comparison based on the boosting capability and number of components is provided, and the performance of the proposed design is analyzed with non-ideal elements. Finally, simulation and experimental studies are carried out to evaluate and validate the performance of the proposed converter.